AZ2703-2A-240A

AZ2703 30 AMP POWER RELAY FEATURES • • • • • • Low cost 30 Amp switching Class B insulation system standard, Class F available PCB Terminals 4 kV dielectric Standard (2.4 mm) and wide contact gap (3.0 mm) available • Epoxy sealed version available • UL, CUR file E44211 • TÜV R50031999 CONTACTS Arrangement Ratings SPST (1 Form X) DPST (2 Form X) Resistive load: Max. switched power: 840 W or 8310 VA Max. switched current: 30 A Max. switched voltage: 150* VDC or 400 VAC *Note: If switching voltage is greater than 30 VDC, special GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (max) Release Time (max) Minimum operations 1 x 106 1 x 105 at 30 A 120 VAC Res. 30 ms at nominal coil voltage 30 ms at nominal coil voltage (with no coil suppression) precautions must be taken. Please contact the factory. Rated Load UL, CUR 30 A at 277 VAC res. 30k cycles [1] 1.5 HP at 120 VAC [1] 3 HP at 240 VAC [1] TV-10 at 120 VAC [1] 30 A at 277 VAC res. 70k cycles [2] 3 HP at 240 VAC 100k cycles [2] 10 A at 120 VAC tungsten load, 10k cycles [2] 27 A at 240 VAC, cos phi = .8, 100k cycles [1] [1] silver cadmium oxide, [2] silver tin oxide (1 Form X only) Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 2000 Vrms between open contacts Insulation Resistance Dropout Ambient Temperature Operating Storage 1000 megohms min. at 20°C, 500 VDC, 50% RH Greater than 5% of nominal coil voltage (DC) Greater than 15% of nominal coil voltage (AC) At nominal coil voltage -40°C (-40°F) to 85°C (185°F) - Class B -40°C (-40°F) to 105°C (221°F) - Class F -40°C (-40°F) to 130°C (266°F) - Class B -40°C (-40°F) to 155°C (311°F) - Class F 0.062" DA at 10–55 Hz TÜV Material Resistance Silver cadmium oxide, silver tin oxide < 100 milliohms initially (24 V, 1 A voltage drop method) Vibration Shock Operating 10 g, 11 ms, 1/2 sine (no false operation) Non-Operating 100 g, 11 ms, 1/2 sine (no damage) Enclosure P.B.T. polyester Tinned copper alloy, PC mount 270°C (518°F) 5 seconds 120 grams COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 1.08 W (DC) 1.2 VA (AC) 3.8 W at 20°C (68°F) ambient 50°C (90°F) at nominal coil voltage Max. 130°C (266°F) - Class B Max. 155°C (311°F) - Class F Terminals Max. Solder Temp. Max. Solder Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 8/31/05W AZ2703 RELAY ORDERING DATA COIL SPECIFICATIONS – DC COIL Nominal Coil VDC 3 6 12 24 48 100 110 200 Must Operate VDC 2.25 4.50 9.00 18.00 36.0 75.0 82.5 150.0 Max. Continuous VDC 4.2 8.4 16.8 33.7 67.5 140.5 154.7 282.4 Coil Resistance ± 10% 4.7 18.8 75 300 1200 5200 6300 21000 ORDER NUMBER* 1 Form X AZ2703–1A–3D AZ2703–1A–6D AZ2703–1A–12D AZ2703–1A–24D AZ2703–1A–48D AZ2703–1A–100D AZ2703–1A–110D AZ2703–1A–200D 2 Form X AZ2703–2A–3D AZ2703–2A–6D AZ2703–2A–12D AZ2703–2A–24D AZ2703–2A–48D AZ2703–2A–100D AZ2703–2A–110D AZ2703–2A–200D COIL SPECIFICATIONS – AC COIL ORDER NUMBER* Nominal Coil Must Operate Max. Continuous Coil Current 1 Form X 2 Form X VAC VAC VAC mA ± 10% 6 4.80 6.6 319 AZ2703–1A–6A AZ2703–2A–6A 12 9.60 13.2 160 AZ2703–1A–12A AZ2703–2A–12A 24 19.2 26.4 80 AZ2703–1A–24A AZ2703–2A–24A 48 38.4 52.8 40 AZ2703–1A–48A AZ2703–2A–48A 120 96.0 132.0 23 AZ2703–1A–120A AZ2703–2A–120A 220 176.0 242.0 10 AZ2703–1A–220A AZ2703–2A–220A 240 192.0 264.0 9.2 AZ2703–1A–240A AZ2703–2A–240A *For epoxy sealed version add suffix “E”. For silver tin oxide add suffix “T” (UL approved for 1 Form X version only). For wide contact gap add suffix “W”. For Class F add suffix “F”. MECHANICAL DATA MOUNTING HOLE LAYOUT .031 [0.8] .274 [6.9] .437 [11.1] .567 [14.4] .437 [11.1] .321 [8.1] .043 [1.1] .504 [12.8] .567 [14.4] 1.418 [36.0] .067 [1.7] .236 [6.0] .432 [11.0] 1.575 [40.0] .207 [5.2] 1.575 [40.0] .748 [19.0] .250 [6.3] .130 [3.3] .748 [19.0] .110 x .032 [2.8 x 0.81] VIEWED TOWARD TERMINALS 1 ø.177 [ø4.5] 2 3 4 WIRING DIAGRAMS 1.374 [34.9] 1 2 3 4 2 3 6 5 2.028 [51.5] 6 2 FORM X 5 6 1 FORM X 5 Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 8/31/05W