AZ695-5G

AZ695 SENSITIVE SUBMINIATURE RELAY FEATURES • Extremely small footprint utilizing only 0.18 square inch of PCB area • Thin vertical profile only 0.256" wide • 1 Form A contact with up to 5 Amp switching capability • High sensitivity, 100 mW pickup • Dielectric strength 3000 Vrms contact to coil • Coils to 24 VDC • Epoxy sealed for automatic wave soldering and cleaning • UL file E44211; CSA file 74461 CONTACTS Arrangement Ratings SPST (1 Form A) Resistive load: Max. switched power: 150 W or 1250 VA Max. switched current: 5 A Max. switched voltage: 150* VDC or 250 VAC Inductive load (p.f. = 0.40, L/R = 7 ms) 2 A at 250 VAC, 30 VDC UL/CSA Ratings 5 A at 30 VDC resistive 5 A at 250 VAC general use 1/10 HP 120 VAC Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 20 million operations 1 X 105 at 5 A, 30 VDC or 250 VAC Res. 6 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 750 Vrms between open contacts (at sea level for 1 min.) 3000 Vrms contact to coil Insulation Resistance Dropout Ambient Temperature Operating Storage Vibration Shock Enclosure 100 megohms min. at 20°C, 500 VDC, 50% RH Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) 0.062" DA at 10–55 Hz 10 g P.B.T. polyester Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 3 grams Material Options: Silver cadmium oxide Silver cadmium oxide with gold plating < 30 milliohms initially (6 V, 1 A, voltage drop method) Resistance COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 100 mW 550 mW at 20°C (68°F) ambient 420 mW at 40°C (104°F) ambient 25°C (45°F) at nominal coil voltage Max. 105°C (221°F) Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Minimum permissible contact load: SCO contact: 100 mA at 5 VDC SCO contact with gold plating: 10 mA at 5 VDC 4. Specifications subject to change without notice. 7/12/01W AZ695 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 6 9 12 18 24 Max. Continuous VDC 8.4 10.1 15.2 20.2 29.5 40.5 Coil Resistance ± 10% 125 180 405 720 1,620 2,880 Must Operate VDC 3.5 4.2 6.3 8.4 12.6 16.8 ORDER NUMBER SCO Contact AZ695–5 AZ695–6 AZ695–9 AZ695–12 AZ695–18 AZ695–24 SCO with Gold Plating Contact AZ695–5G AZ695–6G AZ695–9G AZ695–12G AZ695–18G AZ695–24G MECHANICAL DATA .012 (0.3) .690 (17.5) .012 (0.3) .256 (6.5) .492 (12.5) 0.13 (3.3) .032 (0.8) 0.2 (5.08) .020 (0.5) 0.3 (7.62) 0.1 (2.54) .012 (0.3) .035 (0.9) 0.2 (5.08) PC BOARD LAYOUT .043 (1.1) DIA 0.2 (5.08) WIRING DIAGRAM 13 0.2 (5.08) 0.3 (7.62) 0.1 (2.54) 7 5 Viewed toward terminals 1 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 7/12/01W