AZ697-1C-12D

AZ697 10 AMP MINIATURE POWER RELAY FEATURES • • • • • • • • Dielectric strength 5000 Vrms Low cost Epoxy sealed version available 10 Amp switching — single pole contacts UL TV-5 Isolation spacing greater than 8mm UL Class B insulation system, Class F available UL, CUR file E44211; TÜV file R50129288 CONTACTS Arrangement Ratings SPST (1 Form A) SPDT (1 Form C) Resistive load: Max. switched power: 300 W or 2770 VA Max. switched current: 10 A Max. switched voltage: 150* VDC or 380 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 1 x 107 1 x 105 at 10 A 240 VAC Res. 8 ms at nominal coil voltage 5 ms at nominal coil voltage (with no coil suppression) Rated Load UL, CUR TV-5 at 120 VAC [1][2][3] 10 A at 277 VAC, General Use [1] 10 A 30 VDC, Resistive [1] 1/3 HP at 250 VAC [1] 1/4 HP at 125 VAC N.O. [1] 10 A at 277 VAC, General Use, 100k cycles [2][3] 10 A at 30 VDC, Resistive, 100k cycles [2][3] 1/3 HP at 250 VAC, 100k cycles [2][3] 1/4 HP at 125 VAC, 100k cycles [2][3] 10 A at 250 VAC, 30 VDC Resistive 100k cycles [1][2] 10 A at 250 VAC, 30 VDC Resistive 50k cycles [3] Silver cadmium oxide [1], silver nickel [2], silver tin oxide [3], Gold plating available < 50 milliohms initially (24 V, 1 A voltage drop method) Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance Dropout Ambient Temperature Operating Storage 1000 megohms min. at 20°C, 500 VDC 50% RH Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 90°C (194°F) Class B -40°C (-40°F) to 110°C (230°F) Class F -40°C (-40°F) to 130°C (266°F) Class B -40°C (-40°F) to 155°C (311°F) Class F 0.062" DA at 10–55 Hz 10 g P.B.T. polyester Tinned copper alloy, P. C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 18 grams TÜV Vibration Shock Enclosure Material Resistance Terminals Max. Solder Temp. COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 257 mW 1.9 W at 20°C (68°F) ambient (Class B) 2.5 W at 20°C (68°F) ambient (Class F) 34° C (61°F) at nominal voltage Max. 130°C (266°F) Class B Max. 155° C (311° F) Class F Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 4/9/09W AZ697 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 3 5 6 9 12 18 24 48 60 110 Must Operate VDC 2.1 3.5 4.2 6.3 8.4 12.6 16.8 33.6 42.0 79.3 Max. Continuous VDC 5.7 9.4 11.4 17.4 22.8 27.9 45.7 89.0 115.3 170.5 Coil Resistance 17 47 68 160 275 650 1100 4170 7000 22900 ±10% ±10% ±10% ±10% ±10% ±10% ±15% ±15% ±15% ±15% ORDER NUMBER* Form A (SPST) AZ697–1A–3D AZ697–1A–5D AZ697–1A–6D AZ697–1A–9D AZ697–1A–12D AZ697–1A–18D AZ697–1A–24D AZ697–1A–48D AZ697–1A–60D AZ697–1A–110D Form C (SPDT) AZ697–1C–3D AZ697–1C–5D AZ697–1C–6D AZ697–1C–9D AZ697–1C–12D AZ697–1C–18D AZ697–1C–24D AZ697–1C–48D AZ697–1C–60D AZ697–1C–110D *For silver nickel contacts change “-1A” or “-1C” to “-1AB” or “-1CB”. For silver tin oxide contacts change “-1A” or “-1C” to “-1AE” or “-1CE”. For epoxy seal change “D” to “DE”. For gold plating change “D” or “DE” to “DA” or “DEA”. For Class F insulation add suffix “F” to part number. HARDWARE ORDERING DATA DESCRIPTION Socket ORDER NUMBER ST482–U1 DESCRIPTION Retainer ORDER NUMBER ST482–2 MECHANICAL DATA Form A and C 1.14 (29) .160 ± .015 (4.2 ± .4) .51 (13) PC BOARD LAYOUT Viewed toward terminals .138 .138 .649 (3.5) (3.5) (16.5) .015 (0.38) 1.02 (25.9) .295 (7.5) .08 (2.1) .05 DIA. (1.3) (Form C only) (4 places Form A) (5 places Form C) Terminal No. Dimensions Tol.: ± 0.005 (0.13) 1,2,3,5 0.018 (0.457) x 0.038 (0.965) 4 0.011 (0.279) x 0.038 (0.965) WIRING DIAGRAM ST482-U1 HARDWARE .500 (12.7) .177 MAX. (4.5) .354 (9.0) Form A 1 5 4 3 1 5 Form C 2 4 3 1.22 (30.9) .414 (10.5) .295 (7.5) 1.28 (32.5) .366 (9.3) .125 DIA (3.2) 1.217 (30.9) .158 (4.0) Viewed toward terminals .276 (7.0) .792 (20.1) .059 DIA (1.5) .118 (3.0) 1.004 (26.5) RETAINING CLIP .138 (3.5) ST482-2 Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 4/9/0 W