AZ725-1C-60D

AZ725 MINIATURE POWER RELAY FEATURES • • • • • • • Dielectric strength 5000 Vrms 20 Amp switching — single pole contacts Isolation spacing greater than 8mm Molded materials: all 94 V–0 VDE 6010 - unsealed version only Sealed version available UL, CUR file E43203 CONTACTS Arrangement Ratings SPST (1 Form A) SPDT (1 Form C) Resistive load: Max. switched power: 480 W or 5000 VA Max. switched current: 20 A Max. switched voltage: 150* VDC or 400 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 2 x 107 1 x 105 at 16 A 240 VAC Res. 7 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) Rated Load UL Material Resistance 20 A at 250 VAC resistive Silver cadmium oxide < 30 milliohms initially Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance Dropout Ambient Temperature Operating Storage Vibration 1000 megohms min. at 20°C, 500 VDC, 50% RH Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 130°C (266°F) 0.062" DA at 10–55 Hz 10 g P.B.T. polyester Tinned copper alloy 270°C (518°F) 5 seconds 30 seconds 80°C (176°F) 19 grams COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 270 mW 2.6 W at 20°C (68°F) ambient 2.0 W at 40°C (104°F) ambient 32°C (58°F) nominal coil voltage Max. 130°C (266°F) Shock Enclosure Terminals Max. Solder Temp. Max. Solder Time Max. Immersion Time Max. Solvent Temp Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 5/16/05W AZ725 RELAY ORDERING DATA COIL SPECIFICATIONS — DC Coil Nominal Coil VDC 5 6 12 24 48 60 Must Operate VDC 3.5 4.2 8.4 16.8 33.6 42.0 Max. Continuous VDC 11.3 13.3 26.0 53.5 107.0 135.0 Nominal mA ± 10% 102.0 88.21 46.2 21.8 10.9 8.6 Coil Resistance ±10% 49 68 260 1,100 4,400 7,000 ORDER NUMBER* Form A (SPST) AZ725–1A–5D AZ725–1A–6D AZ725–1A–12D AZ725–1A–24D AZ725–1A–48D AZ725–1A–60D Form C (SPDT) AZ725–1C–5D AZ725–1C–6D AZ725–1C–12D AZ725–1C–24D AZ725–1C–48D AZ725–1C–60D *Add suffix “E” for epoxy sealed version . HARDWARE ORDERING DATA DESCRIPTION Socket Retaining Clip ORDER NUMBER ST484–U1 ST482–2 MECHANICAL DATA .045 (1.1) TYP .493 (12.5) .197 (5) .197 (5) .051 DIA (1.3) (8 HOLES) 1.14 MAX (29) .016 (0.4) TYP .115 (2.9) .295 (7.5) 1.10 MAX (27.9) .197 (5) .590 (15) .414 (10.5) 1.22 (30.9) 1.28 (32.5) .366 (9.3) HARDWARE PC BOARD LAYOUT .500 (12.7) .177 (4.5) MAX .354 (9.0) .125 DIA (0.5) PC BOARD LAYOUT Viewed toward terminals .295 (7.5) .197 (5.0) RETAINING CLIP 1.217 (30.9) .158 (4.0) WIRING DIAGRAMS 1 FORM A (SPST-NO) 8 7 5 4 1 FORM C (SPDT) 8 7 6 5 4 3 .118 (3.0) .197 (5.0) .590 (15) .059 DIA (1.5) 1.044 (26.5) .138 (3.5) Viewed toward terminals 1 2 1 2 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 5/16/05W