AZ762H-1CB-6DSE

AZ762H AZ 16 A SPDT MINIATURE HIGH TEMPERATURE POWER RELAY FEATURES • • • • • • • • High ambient operating temperature (105°C) Dielectric strength 5000 Vrms Low cost Epoxy sealed versions available 16 Amp switching (standard coil only) Class B (130°C) standard Isolation spacing greater than 10 mm UL, CUR file E44211, VDE40006031 CONTACTS Arrangement Ratings SPDT (1 Form C) SPST (1 Form A) Resistive load: Max. switched power: 480 W or 4432 VA Max. switched current: 16 A Max. switched voltage: 150* VDC or 440 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. GENERAL DATA Life Expectancy Mechanical Electrical OperateTime (typical) ReleaseTime (typical) Dielectric Strength (at sea level for1min.) Insulation Resistance Dropout Ambient Temperature Operating Storage Vibration Shock Enclosure Minimum operations 1 x 107 1 x 105 at 16 A 277 VAC general use 7 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) 5000 Vrms coil to contact 1000 Vrms between open contacts 1000 megohms min. at 20°C 500 VDC 50% RH Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 105°C (221°F) -40°C (-40°F) to 130°C (266°F) 0.062" DA at 10–55 Hz 10 g P.B.T. polyester Tinned copper alloy, P. C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 14 grams Rated Load UL, CUR VDE 16 A at 277 VAC general use, 100k cycles 105°C (10A sensitive coil) 16 A at 250 VAC resistive, 105°C (10A sensitive coil) 6 A at 400 VAC resistive, 105°C Silver nickel. Gold plating available < 50 milliohms initially (using 6 V 1 A method) Material Resistance COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Max. Temperature 196 mW Standard 141 mW Sensitive 1.7 W at 20°C (68°F) ambient 26°C (47°F) at nominal coil voltage 130°C (266°F) Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 11/13/08W AZ762H AZ RELAY ORDERING DATA COIL SPECIFICATIONS - STANDARD RELAYS Nominal Coil VDC 5 6 9 12 18 24 48 60 Must Operate VDC 3.5 4.2 6.3 8.4 12.6 16.8 33.6 42.0 Max. Continuous VDC 10.2 12.3 18.5 24.7 37.0 49.4 98.0 112.9 Coil Resistance ±10% 62 90 202 360 810 1440 5760 7500 ORDER NUMBER* Unsealed AZ762H–1CB–5D AZ762H–1CB–6D AZ762H–1CB–5D AZ762H–1CB–12D AZ762H–1CB–18D AZ762H–1CB–24D AZ762H–1CB–48D AZ762H–1CB–60D Sealed AZ762H–1CB–5DE AZ762H–1CB–6DE AZ762H–1CB–19DE AZ762H–1CB–12DE AZ762H–1CB–18DE AZ762H–1CB–24DE AZ762H–1CB–48DE AZ762H–1CB–60DE COIL SPECIFICATIONS - SENSITIVE RELAYS Nominal Coil VDC 5 6 9 12 18 24 48 60 Must Operate VDC 3.75 4.50 6.75 9.0 13.5 18.0 36.0 45.0 Max. Continuous VDC 10.2 12.3 18.5 24.7 37.0 49.4 98.0 112.9 Coil Resistance ± 10% 100 144 324 576 1296 2304 9216 12857 ORDER NUMBER* Unsealed AZ762H–1CB–5DS AZ762H–1CB–6DS AZ762H–1CB–9DS AZ762H–1CB–12DS AZ762H–1CB–18DS AZ762H–1CB–24DS AZ762H–1CB–48DS AZ762H–1CB–60DS Sealed AZ762H–1CB–5DSE AZ762H–1CB–6DSE AZ762H–1CB–9DSE AZ762H–1CB–12DSE AZ762H–1CB–18DSE AZ762H–1CB–24DSE AZ762H–1CB–48DSE AZ762H–1CB–60DSE * For 1 form A contacts substitute “-1AB” for “-1CB.” For gold plated contacts add suffix “A.” 11/13/08W AZ762H HARDWARE ORDERING DATA DESCRIPTION Socket ORDER NUMBER ST484–U1 DESCRIPTION Retainer ORDER NUMBER ST482–3 MECHANICAL DATA 1 .1 6 1 M a x . [2 9 .5 ] .5 2 0 M a x . [1 3 .2 ] V IE W E D T O W A R D S T E R M IN A L S .1 9 7 [5 .0 ] PC B O A R D LA YO U T .619 Max. [15.7] .2 9 5 [7 .5 ] .1 5 4 [3 .9 ] 6 X .0 2 0 [0 .5 ] 2 Xø.0 2 4 [ø0 .6 ] .2 9 5 [7 .5 ] .1 9 7 [5 .0 ] .597 [15.16] .0 9 8 [2 .5 ] .0 9 8 [2 .5 ] 6 Xø.0 5 0 [ø1 .3 ] 2 Xø.0 3 2 [ø0 .8 ] 6 X .0 3 5 [0 .9 ] .2 9 5 [7 .5 ] ST484-U1 .1 9 7 [5 .0 ] .1 9 7 [5 .0 ] HARDWARE .5 0 0 (1 2 .7 ) .1 7 7 (4 .5 ) M AX 1 .2 8 (3 2 .5 ) .1 2 5 D IA (0 .5 ) .3 6 6 (9 .3 ) .3 5 4 (9 .0 ) .597 [15.16] .0 9 8 [2 .5 ] 1 .2 2 (3 0 .9 ) WIRING DIAGRAMS VIEWED TOWARDS TERMINALS .4 1 4 (1 0 .5 ) 5 * 4 3 * 2 R E A IN IN G C L IP T .2 9 5 (7 .5 ) .1 9 7 (5 .0 ) 1 .3 8 5 [3 5 .1 9 ] * 8 7 * 6 1 .5 9 0 (1 5 ) .1 9 7 (5 .0 ) .0 5 9 D IA (1 .5 ) .8 9 5 [2 2 .7 3 ] .6 6 1 [1 6 .7 9 ] * Terminals 3 & 6 not used on form A .1 1 8 (3 .0 ) ST482-3 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 11/13/08W