AZ765-1A-48D

AZ765 SPST SUBMINIATURE POWER RELAY FEATURES • • • • • Small footprint Low cost Epoxy sealed version available 10 Amp switching UL, CUR file E44211 CONTACTS Arrangement Ratings SPST (1 Form A) Resistive load: Max. switched power: 150 W or 1250 VA Max. switched current: 10 A Max. switched voltage: 30* VDC or 250 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 1 x 107 1 x 105 at 10 A 120 VAC Res. 8 ms at nominal coil voltage 5 ms at nominal coil voltage (with no coil suppression) Rated Load UL, CUR Material Resistance Dielectric Strength 2500 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance Dropout Ambient Temperature Operating Storage Vibration Shock 1000 megohms min. at 20°C 500 VDC 50% RH Greater than 5% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 65°C (149°F) -40°C (-40°F) to 105°C (221°F) 0.040" DA at 10–50 Hz 10 g operating, 100 g damage P.B.T. polyester Tinned copper alloy, P. C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 6 grams 10 A at 125 VAC, 5A at 250 VAC 5 A at 30 VDC Silver cadmium oxide < 50 milliohms initially (24 V, 1 A voltage drop method) COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 253 mW Enclosure Terminals Max. Solder Temp. Max. Solder Time 1.1 W at 20°C (68°F) ambient 42°C (76°F) at nominal coil voltage Max. 105°C (221°F) Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 12/11/08W AZ765 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 3 5 6 9 12 18 24 48 Must Operate VDC 2.25 3.75 4.5 6.75 9.0 13.5 18.0 36.0 Max. Continuous VDC 4.7 7.7 9.4 14.0 18.7 28.1 37.5 62.4 Coil Resistance ± 10% 20 55 80 180 320 720 1,280 5,120 ORDER NUMBER* 1 Form A AZ765–1A–3D AZ765–1A–5D AZ765–1A–6D AZ765–1A–9D AZ765–1A–12D AZ765–1A–18D AZ765–1A–24D AZ765–1A–48D *Add suffix “E” for epoxy sealed version. MECHANICAL DATA PC BOARD LAYOUT .717 [18.2] .402 [10.2] .058 [1.48] .500 [12.7] .100 [2.54] .585 [14.85] .300 [7.6] 4 x ø.051 [ø1.3] FORM A .150 [3.8] 2 x .018 SQR. [0.45] VIEWED TOWARD TERMINALS .012 TYP. [0.3] WIRING DIAGRAM 5 4 .039 TYP. [1.0] 1 FORM A 3 VIEWED TOWARD TERMINALS Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 12/11/08W