AZ8462-9

AZ8462 AZ MICROMINIATURE POLARIZED RELAY FEATURES • SMT and DIP mounting available • Microminiature size: up to 50% less board area than previous generation telecom relays • High dielectric and surge voltage: 2.5 KV surge (per Bellcore TA–NWT–001089) 1.5 KV surge (per FCC Part 68) 1,000 Vrms, open contacts • Monostable and bistable (latching) versions available • Low power consumption: 79 mW pickup • Stable contact resistance for low level signal switching • Epoxy sealed for automatic wave soldering and cleaning • UL, CUR file E43203 • All plastics meet UL94 V–0, 30 min. oxygen index GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (max) Release Time (max) Dielectric Strength (at sea level) Minimum operations 1 x 108 at 3Hz 1 x 105 at 0.5 A, 125 VAC, Res. 1 x 105 at 2.0 A, 30 VDC, Res. 4 ms at nominal coil voltage 4 ms at nominal coil voltage (with no coil suppression) See table Greater than 10% of nominal coil voltage 109 ohms min. at 25°C, 500 VDC, 50% RH At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 115°C (239°F) Operational, 3.3 mm DA, 10–55 Hz Non-destructive, 5.5 mm DA, 10–55 Hz Operational, 75 g min., 11 ms Non-destructive, 100 g min., 11 ms 260°C (500°F) for 5 seconds 80°C (176°F) 30 seconds 2 grams P.B.T. polyester Tinned copper alloy, P.C. CONTACTS Arrangement Ratings DPDT (2 Form C) Bifurcated crossbar contacts Resistive load: Max. switched power: 60 W or 62.5 VA Max. switched current: 2.0 A Max. switched voltage: 220 VDC or 250 VAC Rated Load UL/CUR Material Resistance 0.5 A at 125 VAC general use 2.0 A at 30 VDC Silver nickel, gold plated < 50 milliohms initially at 6 V, 1 A Dropout Insulation Resistance Ambient Temperature Operating Storage Vibration Shock Max. Solder Temp. Max. Solvent Temp. Max. Immersion Time Weight COIL (Polarized) Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 79 mW (3–24 VDC) 152 mW (48 VDC) Enclosure Terminals 0.32 W at 20°C (68°F) At 30° C (54°F) nominal coil voltage Max. 115°C (239°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Relay has fixed coil polarity. 4. Specifications subject to change without notice. 4/16/09W AZ8462 AZ RELAY ORDERING DATA STANDARD VERSION Nominal Coil VDC 1.5 3 4.5 5 6 9 12 24 48 Nominal Coil VDC 1.5 3 4.5 5 6 9 12 24 Nominal Coil VDC 1.5 3 4.5 5 6 9 12 24 Must Operate VDC 1.13 2.25 3.38 3.75 4.50 6.75 9.00 18.00 36.0 Set/Reset Voltage 1.13 2.25 3.38 3.75 4.50 6.75 9.00 18.00 Set/Reset Voltage 1.13 2.25 3.38 3.75 4.50 6.75 9.00 18.00 Max. Continuous VDC 2.2 4.5 6.7 7.5 9 13.5 18 36 57.6 Max. Continuous VDC 2.7 5.4 8.1 9.0 10.8 16.2 21.6 43.2 Max. Continuous VDC 2.2 4.5 6.7 7.5 9.0 13.5 18.0 36.0 Coil Resistance ± 10% 16.1 64.3 145 178 257 579 1028 4114 8533 Coil Resistance ± 10% 22.5 90 203 250 360 810 1440 5760 Coil Resistance ± 10% 11.2 45 101 125 180 405 720 2280 ORDER NUMBER (Through Hole) THT SMT* AZ8462S–1.5 AZ8462S–3 AZ8462S–4.5 AZ8462S–5 AZ8462S–6 AZ8462S–9 AZ8462S–12 AZ8462S–24 AZ8462S–48 AZ8462–1.5 AZ8462–3 AZ8462–4.5 AZ8462–5 AZ8462–6 AZ8462–9 AZ8462–12 AZ8462–24 AZ8462-48 SINGLE COIL LATCHING VERSION (Through Hole) THT SMT* AZ8462P1S–1.5 AZ8462P1S–3 AZ8462P1S–4.5 AZ8462P1S–5 AZ8462P1S–6 AZ8462P1S–9 AZ8462P1S–12 AZ8462P1S–24 AZ8462P1–1.5 AZ8462P1–3 AZ8462P1–4.5 AZ8462P1–5 AZ8462P1–6 AZ8462P1–9 AZ8462P1–12 AZ8462P1–24 DUAL COIL LATCHING VERSION (Through Hole) THT SMT* AZ8462P2S–1.5 AZ8462P2S–3 AZ8462P2S–4.5 AZ8462P2S–5 AZ8462P2S–6 AZ8462P2S–9 AZ8462P2S–12 AZ8462P2S–24 AZ8462P2–1.5 AZ8462P2–3 AZ8462P2–4.5 AZ8462P2–5 AZ8462P2–6 AZ8462P2–9 AZ8462P2–12 AZ8462P2–24 *For Tape and Reel add suffix “TR.” For SMT short leg add “1” after S. INITIAL DIELECTRIC STRENGTH (minimum) VRMS, 1 min. 1,000 1,000 1,500 Peak (V) 1,500 2,500 SURGE Rise Time (µS) 10 2 Decay Time* (9µS) (1/2 peak) 160 10 Between open contacts Between contact sets Between coil and contacts * Decay time measured from beginning of surge. 4/16/09W AZ8462 Outline Dimensions(DIP type) SINGLE SIDE STABLE & 1 COIL LATCHING .598MAX [15.20] .303MAX [7.70] Viewed Toward Terminals 2 COIL LATCHING .598MAX [15.20] .303MAX [7.70] PC Board Layout (DIP type) .200 [5.08] .100 [2.54] .362MAX [9.20] .362MAX [9.20] .024 [0.60] .045 [1.15] .200 [5.08] .024 [0.60] .045 [1.15] .200 .100 [5.08] [2.54] .130 [3.30] .130 [3.30] .100 .200 [5.08] [2.54] 8-Ø0.039 [Ø1.00] SINGLE SIDE STABLE & 1 COIL LATCHING .200 [5.08] .100 [2.54] .200 [5.08] .200 [5.08] .200 [5.08] Outline Dimensions(SMT Type ) 2 COIL LATCHING 10-Ø0.039 [Ø1.00] SINGLE SIDE STABLE & 1 COIL LATCHING .598MAX [15.20] .303MAX [7.70] 2 COIL LATCHING PC Board Layout (SMT type) .598MAX [15.20] .303MAX [7.70] .039 [1.00] .200 [5.08] .100 [2.54] .362MAX [9.20] .024 [0.60] .045 [1.15] .382MAX [9.70] .024 [0.60] .045 [1.15] .362MAX [9.20] .122 [3.11] .382MAX [9.70] .283 [7.19] .020 [0.50] .200 .100 [5.08] [2.54] .200 [5.08] .374MAX [9.50] .200 .100 [5.08] [2.54] .200 [5.08] .374MAX [9.50] SINGLE SIDE STABLE & 1 COIL LATCHING .039 [1.00] .200 [5.08] .100 [2.54] 0.122 [3.11] Outline Dimensions(S1 type: Short SMT) SINGLE SIDE STABLE & 1 COIL LATCHING .598MAX [15.20] .303MAX [7.70] .283 [7.19] 2 COIL LATCHING 2 COIL LATCHING .598MAX [15.20] .303MAX [7.70] PC Board Layout (Type S : Short SMT) .362MAX [9.20] .024 [0.60] .045 [1.15] .382MAX [9.70] .024 [0.60] .045 [1.15] .362MAX [9.20] .039 [1.00] .200 [5.08] .100 [2.54] .382MAX [9.70] .122 [2.21] .020 [0.50] .200 .100 [5.08] [2.54] .200 [5.08] .374MAX [7.50] .200 .100 [5.08] [2.54] .200 [5.08] .374MAX [7.50] .247 [6.29] SINGLE SIDE STABLE & 1 COIL LATCHING .039 [1.00] .200 [5.08] .100 [2.54] Wiring Diagram +1 Viewed Toward Terminals 0.122 [2.21] 5 SET 3 4 + 1RESET 3 4 5 SET +1 3 4 5 6+ RESET .247 [6.29] - 12 10 9 8 - + 12 10 9 8 - 12 10 9 8 7 - SINGLE SIDE STABLE 1 COIL LATCHING 2 COIL LATCHING 2 COIL LATCHING Dimensions in inch with millimeters in brackets below. Tolerance: ± .010” 4/16/09W