AZ853PS-12

AZ853 AZ MICROMINIATURE POLARIZED RELAY FEATURES • Conforms to IEC60950/UL1950/EN60950 spacing and high breakdown voltage Clearance: 1.0 mm (between coil and contacts) Creepage: 1.6 mm (between coil and contacts) Basic Insulation: 150 V Working Voltage, Pollution Degree 2 • Monostable and bistable (latching) versions available • High dielectric and surge voltage: 2.5 KV surge (per Bellcore TA–NWT–001089) 1.5 KV surge (per FCC Part 68) 1,000 Vrms, open contacts • Low power consumption: 79 mW pickup • Stable contact resistance for low level signal switching • Epoxy sealed for automatic wave soldering and cleaning • UL file E43203; CSA file 212940 • All plastics meet UL94 V–0, 30 min. oxygen index CONTACTS Arrangement Ratings DPDT (2 Form C) Bifurcated crossbar contacts Resistive load: Max. switched power: 60 W or 62.5 VA Max. switched current: 2.0 A Max. switched voltage: 220 VDC or 250 VAC Rated Load UL/CSA 0.5 A at 125 VAC 2.0 A at 30 VDC 0.3 A at 110 VDC Silver alloy; gold clad < 75 milliohms initially at 6 V, 1 A Ambient Temperature Operating Storage 79 mW (3–12 VDC) 130 mW (24 VDC) 1.0 W at 20°C (68°F) 0.78 W at 40°C (104°F) At nominal coil voltage 18°C (32°F) (3–12 VDC) 25°C (45°F) (24 VDC) Max. 115°C (239°F) Vibration Shock Max. Solder Temp. Temp./Time Max. Solvent Temp. Max. Immersion Time Weight Enclosure Terminals GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Bounce (typical) Capacitance Dielectric Strength (at sea level) Dropout Insulation Resistance Minimum operations 1 x 108 at 3Hz 1 x 105 at 0.5 A, 125 VAC, Res. 2 x 105 at 1.0 A, 30 VDC, Res. 3 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) At 10 mA contact current 1 ms at operate or release < 1 pF at 10 KHz—open contacts < 1 pF at 10 KHz—adjacent contact sets See table Greater than 10% of nominal coil voltage 109 ohms min. at 25°C, 500 VDC, 50% RH At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 115°C (239°F) Operational, 20 g, 10–55 Hz Non-destructive, 30 g, 10–55 Hz Operational, 50 g min., 11 ms Non-destructive, 100 g min., 11 ms 350°C (662°F) for 3 seconds 260°C (500°F) for 10 seconds 80°C (176°F) 30 seconds 1.0 grams P.B.T. polyester Tinned copper alloy, P.C. Material Resistance COIL (Polarized) Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Relay has fixed coil polarity. 4. Specifications subject to change without notice. 6/23/04W AZ853 AZ RELAY ORDERING DATA NON-LATCHING VERSION Nominal Coil VDC 1.5 3 4.5 6 9 12 24 Max. Continuous VDC 2.25 4.5 6.75 9 13.5 18 36 Coil Resistance ± 10% 16.1 64.3 145 257 579 1028 2504 Must Operate VDC 1.13 2.25 3.38 4.5 6.75 9.00 18.00 THT AZ853–1.5 AZ853–3 AZ853–4.5 AZ853–6 AZ853–9 AZ853–12 AZ853–24 ORDER NUMBER SMT* AZ853S–1.5 AZ853S–3 AZ853S–4.5 AZ853S–6 AZ853S–9 AZ853S–12 AZ853S–24 SMTss* AZ853S1–1.5 AZ853S1–3 AZ853S1–4.5 AZ853S1–6 AZ853S1–9 AZ853S1–12 AZ853S1–24 LATCHING VERSION Nominal Coil VDC 1.5 3 4.5 6 9 12 24 Max. Continuous VDC 2.25 4.5 6.75 9 13.5 18 36 Coil Resistance ± 10% 22.5 90 203 360 810 1440 4800 Must Operate VDC 1.13 2.25 3.38 4.50 6.75 9.00 18.00 THT AZ853P–1.5 AZ853P–3 AZ853P–4.5 AZ853P–6 AZ853P–9 AZ853P–12 AZ853P–24 ORDER NUMBER SMT* AZ853PS–1.5 AZ853PS–3 AZ853PS–4.5 AZ853PS–6 AZ853PS–9 AZ853PS–12 AZ853PS–24 SMTss* AZ853PS1–1.5 AZ853PS1–3 AZ853PS1–4.5 AZ853PS1–6 AZ853PS1–9 AZ853PS1–12 AZ853PS1–24 *Tape and reel available (1K pcs/reel minimum) INITIAL DIELECTRIC STRENGTH (minimum) VRMS, 1 min. 1,000 1,000 1,500 Peak (V) 1,500 1,500 2,500 SURGE Rise Time (µS) 10 2 2 Decay Time* (9µS) (1/2 peak) 160 160 10 Between open contacts Between contact sets Between coil and contacts * Decay time measured from beginning of surge. Temperature Profile Packaging Specifications Packaging TEMPERATURE (˚C) SOLDERING Orientation mark side Feeding 250 220 Reel dimensions Tape Dimensions PREHEATING COOLING Top cover tape 170 130 90 - 120 SEC MAX Embossed carrier tape 120 SEC MAX 30 SEC MAX Unit: mm General tolerance is ± 0.2 6/23/04W AZ853 Mechanical Data THT .22 [5.7] .42 42 [10.6] PC Board Layout Viewed toward terminals Wiring Diagram Viewed toward terminals (+) 8- Ø .03 [Ø0.85] .3 [7.6] .125 [3.2] .09 [2.2] 1 2 3 4 .35 .020 [9.0] [0.5] .14 06 [1.5] .016 .126 [3.2] .008 [0.2] .125 [3.2] 8 (-) PC Board Layout Viewed toward terminals .22 [5.7] .3 [7.6] 7 6 5 SMT .42 [10.6] Wiring Diagram Viewed toward terminals (+) .125 [3.2] .09 [2.2] 1 2 3 4 .35 [9.0] 8-.124 [3.1] .06 [1.5] .126 [3.2] .09 .09 [2.2] [2.2] .38 [9.7] .020 [0.5] .21 [5.3] 8 (-) 8-.031 [0.8] 7 6 5 .008 [0.2] .126 [3.2] .29 [7.4] .05 [1.2] SMTss .22 [5.7] .38 [9.7] .35 [9.0] .42 [10.6] .06 [1.5] .126 [3.2] .09 [2.2] .09 [2.2] .016 [0.4] .020 [0.5] .008 [0.2] .126 [3.2] .22 [5.7] .05 [1.2] PC Board Layout Viewed toward terminals .3 [7.6] Wiring Diagram Viewed toward terminals (+) 1 8-.09 [2.25] .175 [4.45] 2 3 4 8-.03 [0.8] 8 (-) 7 6 5 6/23/04W