AZ881-1AB-3D

AZ881 8 A SPST / 5 A DPST POLARIZED SUBMINIATURE POWER RELAY SINGLE SIDE STABLE (NON-LATCHING) AND BISTABLE (LATCHING) FEATURES • • • • • • • Dielectric strength 3000 Vrms Single and dual coil latching versions available Epoxy sealed version available 8 Amp switching Class B (130°C) insulation standard Class F (155°C) insulation available UL, CUR file E44211 GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Set Time (typical) Minimum operations 1 x 107 1 x 105 at 8 A 250 VAC resistive (SPST) 5 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) 5 ms at nominal coil voltage 4 ms at nominal coil voltage 4000 Vrms contact to coil 1000 Vrms between open contacts 2000 Vrms between contact sets 1000 megohms min. at 20°C 500 Vdc 50% RH Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 130°C (266°F) 0.078” DA at 10 to 55 Hz 20 g functional 100 g destructive P.B.T. polyester Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 4.7 grams CONTACTS Arrangement Ratings SPST (1 Form A), DPST (2 Form A) DPST (1 Form A and 1 Form B) Resistive load: Max. switched power: 150 W or 2000 VA (SPST) 150 W or 1250 VA (DPST) Max. switched current: 8 A (SPST) 5 A (DPST) Max. switched voltage:150 VDC or 380 VAC* Reset Time (typical) Dielectric Strength (at sea level) Insulation Resistance Dropout Ambient Temperature Operating Storage Vibration Shock Enclosure Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR SPST 8 A at 250 VAC resistive, 100k cycles 5 A at 30 VDC resistive, 100k cycles 1/6 HP at 250 VAC DPST 5 A at 250 VAC resistive, 100k cycles 5 A at 30 VDC resistive, 100k cycles 1/6 HP at 250 VAC Material Resistance Silver nickel, gold plating optional < 50 milliohms initially (6 V 1 A voltage drop method) COIL Power At Pickup Voltage (typical) 192 mW (single side stable, 2 coil latching) 96 mW (1 coil latching) Weight NOTES 1. 2. 3. 4. All values at 20°C (68°F). Relay may pull in with less than “Must Operate” value. Relay has fixed coil polarity. For complete isolation between the relay’s magnetic fields, it is recommended that a .197" (5.0 mm) space be provided between adjacent relays. 5. Relay adjustment may be affected if undue pressure is exerted on relay case. 6. Specifications subject to change without notice. Max. Continuous Dissipation Temperature Rise Max. Temperature 0.75 W at 20°C (68°F) ambient 30°C (54°F) at nominal coil voltage 130°C (266°F) Class B, 155°C (311°F) Class F 1/29/07W AZ881 RELAY ORDERING DATA AZ881 COIL SPECIFICATIONS - SINGLE SIDE STABLE Nominal Coil VDC 3 5 6 9 12 24 Must. Operate VDC 2.4 4.0 4.8 7.2 9.6 19.2 Max. Continuous VDC 4.7 7.9 9.6 14.4 19.2 37.9 Coil Resistance ± 10% 30 83 120 270 480 1920 1 Form A AZ881-1A-3D AZ881-1A-5D AZ881-1A-6D AZ881-1A-9D AZ881-1A-12D AZ881-1A-24D ORDER NUMBER* 2 Form A AZ881-2A-3D AZ881-2A-5D AZ881-2A-6D AZ881-2A-9D AZ881-2A-12D AZ881-2A-24D 1 Form A 1 Form B AZ881-1AB-3D AZ881-1AB-5D AZ881-1AB-6D AZ881-1AB-9D AZ881-1AB-12D AZ881-1AB-24D *Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated contacts. Add suffix “R” for reversed polarity coil. Add suffix “F” for class F insulation. AZ881P1 COIL SPECIFICATIONS - SINGLE COIL LATCHING Nominal Coil VDC 3 5 6 9 12 Must. Operate VDC 2.4 4.0 4.8 7.2 9.6 Max. Continuous VDC 6.7 11.2 13.4 20.1 26.8 Coil Resistance ± 10% 60 167 240 540 960 1 Form A AZ881P1-1A-3D AZ881P1-1A-5D AZ881P1-1A-6D AZ881P1-1A-9D AZ881P1-1A-12D ORDER NUMBER* 2 Form A AZ881P1-2A-3D AZ881P1-2A-5D AZ881P1-2A-6D AZ881P1-2A-9D AZ881P1-2A-12D 1 Form A 1 Form B AZ881P1-1AB-3D AZ881P1-1AB-5D AZ881P1-1AB-6D AZ881P1-1AB-9D AZ881P1-1AB-12D *Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated contacts. Add suffix “R” for reversed polarity coil. Add suffix “F” for class F insulation. AZ881P2 COIL SPECIFICATIONS - DUAL COIL LATCHING Nominal Coil VDC 3 5 6 9 12 24 Must. Operate VDC 2.4 4.0 4.8 7.2 9.6 19.2 Max. Continuous VDC 4.7 7.9 9.5 14.2 19.0 37.9 Coil Resistance ± 10% 30 83 120 270 480 1920 1 Form A AZ881P2-1A-3D AZ881P2-1A-5D AZ881P2-1A-6D AZ881P2-1A-9D AZ881P2-1A-12D AZ881P2-1A-24D ORDER NUMBER* 2 Form A AZ881P2-2A-3D AZ881P2-2A-5D AZ881P2-2A-6D AZ881P2-2A-9D AZ881P2-2A-12D AZ881P2-2A-24D 1 Form A 1 Form B AZ881P2-1AB-3D AZ881P2-1AB-5D AZ881P2-1AB-6D AZ881P2-1AB-9D AZ881P2-1AB-12D AZ881P2-1AB-24D *Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated contacts. Add suffix “R” for reversed polarity coil. Add suffix “F” for class F insulation. 1/29/07W AZ881 AZ MECHANICAL DATA Single side stable &1 coil latching Outline Dimensions 0.795MAX [20.2] -1A 0.433MAX [11.0] .795MAX [20.2] -2A, -1AB .433MAX [11.0] .394MAX [10.00] .394MAX [10.00] .134 [3.40] .048 [1.22] .400 [10.16] .300 [7.62] .031 [0.80] .016 [0.40] .300 [7.62] .016 [0.40] .134 [3.40] .048 [1.22] .400 [10.16] .300 [7.62] .031 [0.80] .016 [0.40] .300 [7.62] .016 [0.40] 2 coil latching -1A .795MAX [20.2] .433MAX [11.0] .795MAX [20.2] -1A, -1AB .433MAX [11.0] .394MAX [10.00] .394MAX [10.00] .134 [3.40] .048 [1.22] .100 [2.54] .400 [10.16] .300 [7.62] .031 [0.80] .016 [0.40] .300 [7.62] .016 [0.40] .134 [3.40] .048 [1.22] .100 [2.54] .400 [10.16] .300 [7.62] .031 [0.80] .016 [0.40] .300 [7.62] .016 [0.40] PC Board Layout -1A .400 [10.16] Single side stable & 1 coil latching -1 AB .300 [7.62] .400 [10.16] .300 [7.62] Wiring Diagram Single side stable (Deenergized condition) -1 A + + -2 A + -1 AB .300 [7.62] .300 [7.62] - - - 4-Ø.047 [Ø1.20] 6-Ø.047 [Ø1.20] 1 coil latching(Reset condition) -1 A -2 A + set reset + set reset + -1 AB -1 A 2 coil latching .100 [25.4] .300 [7.62] .300 [7.62] .100 [25.4] -2A, -1 AB + set reset + - - + - .300 [7.62] .300 [7.62] 2 coil latching(Reset condition) .300 [7.62] -1 A -2 A + set + reset + set + reset - -1 AB .300 [7.62] + set + reset - 6-[Ø.047] [Ø1.20] 8-[Ø.047] [Ø1.20] - - - - Viewed Toward Terminals Viewed Toward Terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 1/29/07W