SG-24FD38Z15P

SG-24F THREE PHASE SOLID STATE RELAY 10 THRU 25 AMPS 36 TO 440 VRMS FEATURES • • • • • • • • Photo isolation LED status indicator Up to 800V blocking voltage Both “Zero Voltage” and phase controllable “Random” Switching versions High surge capability Built-in snubber Triac Output Circuitry UL, CUR approval pending INPUT Type Control Voltage Range Turn On Voltage Turn Off Voltage Max. Input Current Max. Reverse Voltage D38 X Z10 D38 X Z15 3 to 32 VDC 3 VDC max. 1 VDC min. 35 mA at 32 VDC -32 VDC D38 X Z25 OUTPUT Operating Voltage Range Blocking Voltage 36 to 440 Vrms 800 Vpk Type Load Current Range (A) Max. Surge Current (1/2 Cycle) Max. Leakage Current Voltage On-state Drop (max.) Max. Turn-on Time Max. Turn-off Time Min. Off-state Dv/Dt at Maximum Rated Voltage Min. Power Factor Allowable D38 X Z10 0.1 to 10 100 Apk 3 mA D38 X Z15 0.1 to 15 150 Apk 5 mA 1.5 Vrms 1/2 1/2 D38 X Z25 0.1 to 25 250 Apk 10 mA cycle plus 1 ms cycle plus 1 ms 200 V/us 0.5 GENERAL Dielectric Strength Insulation Resistance Max. Capacitance (in/out) Ambient Temperature Mounting Termination Weight 4000 Vrms min. (at 50/60 Hz, 1 min.) 1000 megohms min. (at 500 VDC) 8 pf Operating: -30°C (-22°F) to 80°C (176°F) Storage: -30°C (-22°F) to 100°C (212°F) Panel Mount Screw 315 g 7/16/08W SG-24F RELAY ORDERING DATA SG-24F MODEL D INPUT VOLTAGE D: 3VDC TO 32VDC 38 LOAD VOLTAGE 36 TO 440 VAC Z ZERO CROSS FUNCTION Z: Zero cross turn-on P: Non-zero cross turn-on 25 LOAD CURRENT 10: 10 Amp 15: 15 Amp 25: 25 Amp P PHASE LOSS PROTECTION P- With NIL- Without MECHANICAL DATA Outline Dimensions 6-M4 2-M3 .827 [21] SG-24F/ 1.181 [30] Max Wiring Diagram 4-R.104 [R2.65] 2.953 [75] Max 1.874 [47.6] 2.126 [54] U LOAD 3.614 [91.8] 4.134 [105] Max V LOAD W LOAD + INPUT L1 L2 L3 - Outline Dimensions .827 [21] 6-M4 3-M3 SG-24F/ P 4-R.104 [R2.65] 1.874 [47.6] 2.953 [75] 2.126 [54] 1.181 [30] Max Wiring Diagram U LOAD 3.614 [91.8] 4.134 [105] Max V LOAD W LOAD + INPUT N L1 L2 L3 - Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" INSTALLATION 1. When mounting the relays side by side, provide a space equivalent to the width of a single SSR between two adjacent SSRs. Otherwise, reduce the load current flow to 1/2 to 1/3 of the rated current. When mounting relays on heat sink surface, first apply a heat conductive grease to the metal back surface of the SSR. Press the SSR firmly onto the heat sink to ensure a good seal. Screw the SSR down to the heat sink. Next, wire the screw terminals and securely tighten the screws. PRECAUTIONS 1. Before connecting a load that generates a high surge current, such as a lamp load to the SSR, make sure that the SSR can withstand the surge current of the load. The product data sheet shows the non-repetitive peak value of the surge current that flows through the SSR. Normally, use 1/2 of the non-repetitive peak surge current as the standard value. If a surge current exceeding that value is expected, connect a quick-blowing fuse to protect the SSR. 2. 2. 3. 7/16/08W SG-24F HEAT SINK SF92B-150 4-M5 1.874 [ [47.6] ] 5.157 [131] 4.72 [120] 5.59 [142] 3.15 [80] 3.614 [91.8] .118 [3] .157 [4] 2.165 [55] 4.72 [120] 5.906 [150] HARDWARE ORDERING DATA DESCRIPTION Heat Sink ORDER NUMBER SF92B-150 CHARACTERISTICS CURVE 7/16/08W