AZ100EP16FET

ARIZONA MICROTEK, INC. AZ100EP16FE ECL/PECL High Speed VCSEL Driver with Variable Output Swing or Limiting Amplifier FEATURES • • • • Silicon-Germanium for High Speed Operation 6 Max Min 0° C Typ >6 Max Min 25° C Typ >6 Max Min 85° C Typ >6 Max Unit GHz 100 150 155 4 240 20 VCC 100 150 155 4 240 15 VCC 100 150 155 4 240 15 VCC 120 170 175 4 280 15 VCC ps ps mV V 150 VEE + 2.0 150 VEE + 2.0 150 VEE + 2.0 150 VEE + 2.0 Small Signal Gain 28 dB Output Rise/Fall Times Q 130 130 130 130 ps (20% - 80%) Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(min) and 1V. The lower end of the VCMR range varies 1:1 with VEE and is equal to VEE + 2V. Differential input, differential output. 180Ω to VEE on Q/Q outputs with 50Ω AC coupled load. ¯ See Figure 2. July 2007 * REV - 8 www.azmicrotek.com 2 AZ100EP16FE Typical AZ100EP16FE Voltage Output Swing at +25C, VEE Nom (see Figure 1) 100 VSWING (% pk-pk differential) 1.240 V (100K ECL) 75 %OUT 100K ECL 50 25 0 0.0 0.4 0.8 1.2 1.6 VCTRL (V) Figure 1: Typical Application 5K V CTRL 1 8 V CC D 2 7 Q Q D 3 6 180 VREF 4 5 VEE 180 50 50 - 3.3V Figure 2: Large Signal Performance* 900 800 700 600 VOUTpp (mV) 500 400 300 VCTRL=VCC-0.5V VCTRL=VCC-1.0V VCTRL=VCC-1.5V VCTRL=VCC-2.0V 200 100 0 0 1000 2000 3000 FREQUENCY (MHz) 4000 5000 6000 VCTRL=VCC *Measured using a 750mV differential input source at 50% duty cycle. July 2007 * REV - 8 www.azmicrotek.com 3 AZ100EP16FE PACKAGE DIAGRAM TSSOP 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z θ MILLIMETERS MIN MAX 1.10 0.05 0.15 0.75 0.95 0.25 0.22 0.40 0.13 0.23 2.90 3.10 2.90 3.10 0.65 4.75 5.05 0.95 0.40 0.70 0.10 0.08 0.10 0.38 0.64 6O 0O July 2007 * REV - 8 www.azmicrotek.com 4 AZ100EP16FE Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part. July 2007 * REV - 8 www.azmicrotek.com 5