AZ100EP16T

ARIZONA MICROTEK, INC. AZ10EP16 AZ100EP16 ECL/PECL Differential Receiver FEATURES PACKAGE AVAILABILITY • • • • Silicon-Germanium for High Speed Operation 150ps Typical Propagation Delay Internal Input Pulldown Resistors Functionally Equivalent to ON Semi MC10EP16 & MC100EP16 PACKAGE SOIC 8 SOIC 8 TSSOP 8 TSSOP 8 1 2 PART NUMBER AZ10EP16D AZ100EP16D AZ10EP16T AZ100EP16T MARKING AZM10EP16 AZM100EP16 AZTEP16 AZHEP16 NOTES 1,2 1,2 1,2 1,2 Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date Code “YWW” on underside of part. DESCRIPTION The AZ10/100EP16 is a Silicon–Germanium (SiGe) differential receiver. The device is functionally equivalent to the AZ10/100EL16 device with higher performance capabilities. With output transition times significantly faster than the AZ10/100EL16, the EP16 is ideally suited for interfacing with high frequency sources. The EP16 provides a VBB output for single-ended use or a DC bias reference for AC coupling to the device. For single-ended input applications, the VBB reference should be connected to one side of the D/D differential input pair. ¯ The input signal is then fed to the other D/D input. The VBB pin can support 1.5mA sink/source current. When ¯ used, the VBB pin should be bypassed to ground via a 0.01μF capacitor. Under open input conditions internal input clamps will force the Q output LOW. NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established. PIN DESCRIPTION PIN D, D ¯ Q, Q ¯ VBB VCC VEE NC FUNCTION Data Inputs Data Outputs Reference Voltage Output Positive Supply Negative Supply No Connect LOGIC DIAGRAM AND PINOUT ASSIGNMENT NC 1 8 VCC D 2 7 Q D 3 6 Q VBB 4 5 VEE 1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541 www.azmicrotek.com AZ10EP16 AZ100EP16 Absolute Maximum Ratings are those values beyond which device life may be impaired. Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +4.5 0 to +4.5 -4.5 to 0 -4.5 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA °C °C 10K ECL DC Characteristics (VEE = -3.0V to -3.6V, VCC = GND) Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. Characteristic Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Reference Voltage Input HIGH Current Input LOW Current 1 Min -1135 -1935 -1200 -1935 -1430 -40°C Typ Max -885 -1685 -885 -1530 -1300 175 Min 0° C Typ Max -1380 -1270 175 Min -1070 -1870 -1150 -1870 -1350 25° C Typ -945 -1745 Max -820 -1620 -820 -1450 -1250 175 Min -1010 -1810 -1090 -1810 -1310 85° C Typ Max -760 -1560 -760 -1410 -1190 175 Unit mV mV mV mV mV μA μA 0.5 -150 Power Supply Current 20 25 33 Each output is terminated through a 50Ω resistor to VCC – 2V. D D ¯ 0.5 -150 21 26 34 0.5 -150 21 27 35 0.5 -150 23 29 37 mA 10K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V) Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. 2. Characteristic 1,2 Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Reference Voltage1 1920 2030 Input HIGH Current 175 Input LOW Current D 0.5 0.5 0.5 D ¯ -150 -150 -150 Power Supply Current 20 25 33 21 26 34 21 For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50Ω resistor to VCC – 2V. Min 2165 1365 2100 1365 1870 -40°C Typ Max 2415 1615 2415 1770 2000 175 Min 0° C Typ Max Min 2230 1430 2035 1430 1950 25°C Typ 2355 1555 Max 2480 1680 2480 1850 2050 175 Min 2290 1490 2210 1490 1990 85°C Typ Max 2540 1740 2540 1890 2110 175 Unit mV mV mV mV mV μA μA 27 35 0.5 -150 23 29 37 mA 100K ECL DC Characteristics (VEE = -3.0V to -3.6V, VCC = GND) Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. Characteristic Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Reference Voltage Input HIGH Current Input LOW Current 1 Min -1085 -1830 -1220 -1830 -1440 -40°C Typ Max -880 -1555 -880 -1540 -1320 175 Min -1025 -1810 -1160 -1810 -1380 0° C Typ Max -880 -1620 -880 -1480 -1260 175 Min -1025 -1810 -1160 -1810 -1380 25° C Typ -955 -1705 Max -880 -1620 -880 -1480 -1260 175 Min -1025 -1810 -1160 -1810 -1380 85° C Typ Max -880 -1620 -880 -1480 -1260 175 Unit mV mV mV mV mV μA μA 0.5 -150 Power Supply Current 19 24 32 Each output is terminated through a 50Ω resistor to VCC – 2V. D D ¯ 0.5 -150 20 25 33 0.5 -150 21 26 35 0.5 -150 23 29 38 mA November 2006 * REV - 5 www.azmicrotek.com 2 AZ10EP16 AZ100EP16 100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V) Symbol VOH VOL VIH VIL VBB IIH IIL IEE 1. 2. Characteristic Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Reference Voltage1 Input HIGH Current Input LOW Current 1,2 Min 2215 1470 2080 1470 1860 -40°C Typ Max 2420 1745 2420 1760 1980 175 Min 2275 1490 2140 1490 1920 0° C Typ Max 2420 1680 2420 1820 2040 175 Min 2275 1490 2140 1490 1920 25°C Typ 2345 1595 Max 2420 1680 2420 1820 2040 175 Min 2275 1490 2140 1490 1920 85°C Typ Max 2420 1680 2420 1820 2040 175 Unit mV mV mV mV mV μA μA 0.5 0.5 0.5 -150 -150 -150 Power Supply Current 19 24 32 20 25 33 21 For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50Ω resistor to VCC – 2V. D D ¯ 26 35 0.5 -150 23 29 38 mA AC Characteristics (VEE = -3.0 to -3.6V, VCC = GND or VEE = GND, VCC = +3.0V to +3.6V) Symbol fmax tPLH / tPHL tSKEW VPP (AC) VCMR tr / t f 1. 2. 3. 4. Characteristic Maximum Toggle Frequency4 Input to (DIFF) Output Delay 1 Duty Cycle Skew (Diff) Minimum Input Swing2 Common Mode Range3 Min -40°C Typ >4 100 150 VEE + 2.0 160 5 VCC 150 VEE + 2.0 240 100 Max Min 0° C Typ >4 160 5 240 20 VCC 150 VEE + 2.0 100 Max Min 25° C Typ >4 160 5 240 20 VCC 150 VEE + 2.0 120 Max Min 85° C Typ >4 190 5 280 20 VCC Max Unit GHz ps ps mV V ps Output Rise/Fall Times Q 120 170 130 180 130 180 150 200 (20% - 80%) Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(min) and 1V. See Graph Below. Large Signal Performance* 900 800 700 600 VOUTpp (mV) 500 400 300 200 100 0 0 1000 2000 3000 FREQUENCY (MHz) 4000 5000 6000 *Measured using a 750mV differential input source at 50% duty cycle. November 2006 * REV - 5 www.azmicrotek.com 3 AZ10EP16 AZ100EP16 PACKAGE DIAGRAM SOIC 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z θ MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O November 2006 * REV - 5 www.azmicrotek.com 4 AZ10EP16 AZ100EP16 PACKAGE DIAGRAM TSSOP 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z θ MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O November 2006 * REV - 5 www.azmicrotek.com 5 AZ10EP16 AZ100EP16 Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part. November 2006 * REV - 5 www.azmicrotek.com 6