AZ10EL32D

ARIZONA MICROTEK, INC. AZ10EL32 AZ100EL32 FEATURES • • • • • PACKAGE 510ps Propagation Delay 3.0GHz Toggle Frequency High Bandwidth Output Transitions 75kΩ Internal Input Pulldown Resistors Direct Replacement for ON Semiconductor MC10EL32 & MC100EL32 SOIC 8 SOIC 8 SOIC 8 RoHS Compliant / Lead (Pb) Free TSSOP 8 TSSOP 8 1 2 ECL/PECL ÷ 2 Divider PACKAGE AVAILABILITY PART NUMBER AZ10EL32D AZ100EL32D AZ100EL32D+ AZ10EL32T AZ100LVEL32T MARKING AZM10 EL32 AZM100 EL32 AZM100+ EL32 AZT EL32 AZH EL32 NOTES 1,2 1,2 1,2 1,2 1,2 Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date code format: “Y” or “YY” for year followed by “WW” for week on underside of part. DESCRIPTION The AZ10/100EL32 is an integrated ÷2 divider. The reset pin is asynchronous and is asserted on the rising edge. Upon power-up, the internal flip-flop will attain a random logic state; the reset allows for the synchronization of multiple EL32’s in a system. The EL32 provides a VBB output for single-ended use or a DC bias reference for AC coupling to the device. For single-ended input applications, the VBB reference should be connected to one side of the CLK/CLK differential input ¯¯¯¯ pair. The input signal is then fed to the other CLK/CLK input. The VBB pin should be used only as a bias for the ¯¯¯¯ EL32 as its sink/source capability is limited. When used, the VBB pin should be bypassed to ground via a 0.01μF capacitor. NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established. LOGIC DIAGRAM AND PINOUT ASSIGNMENT RESET 1 8 VCC PIN DESCRIPTION PIN CLK, CLK ¯¯¯ RESET VBB Q, Q ¯ VCC VEE FUNCTION Clock Inputs Asynchronous Reset Reference Voltage Output Data Outputs Positive Supply Negative Supply R CLK 2 ÷2 CLK 3 6 Q 7 Q VBB 4 5 VEE 1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541 www.azmicrotek.com AZ10EL32 AZ100EL32 Absolute Maximum Ratings are those values beyond which device life may be impaired. Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA °C °C 10K ECL DC Characteristics (VEE = -4.75V to -5.5V, VCC = GND) Symbol VOH VOL VIH VIL IIH IIL VBB IEE 1. Characteristic 1 Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current 0.5 0.5 Output Reference -1430 -1300 -1380 Voltage Power Supply Current 25 30 Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1080 -1950 -1230 -1950 -40°C Typ Max -890 -1650 -890 -1500 150 Min -1020 -1950 -1170 -1950 0° C Typ Max -840 -1630 -840 -1480 150 -1270 Min -980 -1950 -1130 -1950 0.5 -1350 25° C Typ Max -810 -1630 -810 -1480 150 -1250 Min -910 -1950 -1060 -1950 0.5 -1310 85° C Typ Max -720 -1595 -720 -1445 150 -1190 Unit mV mV mV mV μA μA mV mA 25 30 25 30 25 30 10K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol VOH VOL VIH VIL IIH IIL VBB IEE 1. 2. Characteristic 1,2 Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current Input LOW Current 0.5 0.5 0.5 Output Reference 3570 3700 3620 3730 3650 Voltage Power Supply Current 25 30 25 30 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50Ω resistor to VCC – 2V. Min 3920 3050 3770 3050 -40°C Typ Max 4110 3350 4110 3500 150 Min 3980 3050 3830 3050 0° C Typ Max 4160 3370 4160 3520 150 Min 4020 3050 3870 3050 25°C Typ Max 4190 3370 4190 3520 150 3750 Min 4090 3050 3940 3050 0.5 3690 85°C Typ Max 4280 3405 4280 3555 150 3810 Unit mV mV mV mV μA μA mV mA 25 30 25 30 100K ECL DC Characteristics (VEE = -4.2V to -5.5V, VCC = GND) Symbol VOH VOL VIH VIL IIH IIL VBB IEE 1. Characteristic 1 Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current 0.5 0.5 Output Reference -1380 -1260 -1380 Voltage Power Supply Current 25 30 Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1085 -1830 -1165 -1810 -40°C Typ -1005 -1695 Max -880 -1555 -880 -1475 150 Min -1025 -1810 -1165 -1810 0° C Typ -955 -1705 Max -880 -1620 -880 -1475 150 -1260 Min -1025 -1810 -1165 -1810 0.5 -1380 25° C Typ -955 -1705 Max -880 -1620 -880 -1475 150 -1260 Min -1025 -1810 -1165 -1810 0.5 -1380 85° C Typ -955 -1705 Max -880 -1620 -880 -1475 150 -1260 Unit mV mV mV mV μA μA mV mA 25 30 25 30 29 35 November 2006 * REV - 4 www.azmicrotek.com 2 AZ10EL32 AZ100EL32 100K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol VOH VOL VIH VIL IIH IIL VBB IEE 1. 2. Characteristic 1,2 Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current Input LOW Current 0.5 0.5 0.5 Output Reference 3620 3740 3620 3740 3620 Voltage Power Supply Current 25 30 25 30 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50Ω resistor to VCC – 2V. Min 3915 3170 3835 3190 -40°C Typ 3995 3305 Max 4120 3445 4120 3525 150 Min 3975 3190 3835 3190 0° C Typ 4045 3295 Max 4120 3380 4120 3525 150 Min 3975 3190 3835 3190 25°C Typ 4045 3295 Max 4120 3380 4120 3525 150 3740 Min 3975 3190 3835 3190 0.5 3620 85°C Typ 4045 3295 Max 4120 3380 4120 3525 150 3740 Unit mV mV mV mV μA μA mV mA 25 30 29 35 AC Characteristics (VEE =10E(-4.75V to -5.5V), 100E(-4.2V to -5.5V); VCC =GND or VEE =GND, VCC =10E(+4.75V to +5.5V), 100E(+4.2V to +5.5V)) Symbol fmax tPLH/tPHL VPP (AC) VCMR tr / t f 1. 2. Characteristic Maximum Toggle Frequency Propagation Delay CLK to Q Reset to Q Minimum Input Swing1 Common Mode Range 2 Min 2.2 360 390 150 VCC 2.5 -40°C Typ 3.0 500 540 Max Min 2.6 0° C Typ 3.0 500 540 Max Min 2.6 25° C Typ 3.0 510 540 Max Min 2.6 85° C Typ 3.0 540 550 Max Unit GHz 640 690 VCC 0.4 410 440 150 VCC 2.5 590 640 VCC 0.4 420 440 150 VCC 2.5 600 640 VCC 0.4 450 450 150 VCC 2.5 630 650 VCC 0.4 ps mV V Output Rise/Fall Times Q 100 350 100 350 100 350 100 350 ps (20% - 80%) VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. VCMR is defined as the range within which the VIH level may vary, with the device still meeting the propagation delay specification. The VIL level must be such that the peak-to-peak voltage is less than 1.0V and greater than or equal to VPP(min). Figure 1: Timing Diagram D RESET Q November 2006 * REV - 4 www.azmicrotek.com 3 AZ10EL32 AZ100EL32 PACKAGE DIAGRAM SOIC 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z θ MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O November 2006 * REV - 4 www.azmicrotek.com 4 AZ10EL32 AZ100EL32 PACKAGE DIAGRAM TSSOP 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z θ MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O November 2006 * REV - 4 www.azmicrotek.com 5 AZ10EL32 AZ100EL32 Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part. November 2006 * REV - 4 www.azmicrotek.com 6