ARIZONA MICROTEK, INC.
AZ12010
Multiply by 16, 32 Phase-Locked Loop Clock Generator FEATURES
• • • • • •
Differential Inputs/Outputs for External Voltage Controlled SAW Oscillator Optional Internal Crystal Oscillator Driver Internal Edge-Matching Phase/Frequency Detector Internal Charge-Pump/Integrator Amplifier RF Bipolar Design for Low Phase Noise Available in a 3x3 mm MLP Package PACKAGE
MLP 16 (3x3) MLP 16 (3x3) RoHS Compliant / Lead (Pb) Free MLP 16 (3x3) MLP 16 (3x3) RoHS Compliant / Lead (Pb) Free DIE
1 2 3
PACKAGE AVAILABILITY PART NO.
AZ12010AL AZ12010AL+ AZ12010BL AZ12010BL+ AZ12010XP
MARKING
AZ12010A AZ12010A+ AZ12010B AZ12010B+ N/A
NOTES
1,2 1,2 1,2 1,2 3
DESCRIPTION
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date code format: “YY” for year followed by “WW” for week. Waffle Pack
The AZ12010 contains all of the functional elements necessary to implement a Phase-Locked Loop for clock multiplication at frequencies up to 800 MHz. A fixed 32 times multiplication allows the use of low cost crystals or a low frequency reference signal. The output can be divided by two for 16 times net multiplication. The VCSO is differentially or single-ended driven using the chip CML SAW outputs. The dynamic properties of the PLL are under the control of the user through selection of the desired external components. 1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541 www.azmicrotek.com
AZ12010
3X3 MLP 16 PACKAGE AZM12010A: CPPOL pulled High AZM12010B: CPPOL pulled Low
November 2006 * REV - 5
www.azmicrotek.com 2
AZ12010
DIE MAP Pad Center Locations Signal Name SAWIN ¯¯¯¯¯¯¯ SAWIN TEST ENABLE VEE REFIN ¯¯¯¯¯¯¯¯ REFOUT CPOUT CPREF INTREF INTSUM VEE INTOUT CPPOL VBB VEEP Q ¯ Q VCC VCC SAWOUT ¯¯¯¯¯¯¯¯ SAWOUT DIV_SEL VEE November 2006 * REV - 5 X coordinate (μ) -522.0 -522.0 -522.0 -522.0 -522.0 -522.0 -365.0 -213.0 -61.0 91.0 243.0 395.0 552.0 552.0 552.0 552.0 552.0 552.0 395.0 243.0 91.0 -61.0 -219.0 -377.0 www.azmicrotek.com 3 Y coordinate (μ) 372.3 220.3 68.3 -83.7 -235.7 -387.7 -515.8 -515.8 -515.8 -515.8 -515.8 -515.8 -387.7 -235.7 -83.7 68.3 220.3 372.3 509.9 509.9 509.9 509.9 509.9 509.9
AZ12010
AZ12010 FUNCTIONAL PIN/PAD DESCRIPTIONS Functional Description Reference Frequency Input This pin/pad includes an on-chip 470 Ω pull down resistor to VBB. The input from the reference circuit should be AC coupled. Reference Frequency Output This pin is an inverted and amplified version of the signal on the REFIN pin. The gain from REFIN to ¯¯¯¯¯¯¯¯ is REFOUT approximately 20. If VEEP is connected to VEE, a 4 ma on-chip current source is provided for the output. ¯¯¯¯¯¯¯¯ is not available on the packaged versions (AZ12010A, AZ12010B). REFOUT Charge Pump Reference Output The pin/pad voltage is nominally 1.2 volts below VCC. Charge Pump Output The charge pump output voltage is VCPREF ±0.3V during a phase correction pulse. When there is no correction pulse the output goes high impedance. Charge Pump Polarity When this pin/pad is pulled high the PLL operates with a VCSO circuit exhibiting negative pulling slope (the VCSO frequency goes down when the control voltage goes up). When this pin/pad is pulled low (AZM12010B) the PLL operates with a VCSO circuit exhibiting positive pulling slope (the VCSO frequency goes up when the control voltage goes up). If the pin/pad is left open (AZM12010A), an internal pullup resistor selects negative pulling slope mode. Integrator Reference Input This pin/pad should be connected to CPREF through a bias current cancellation network Integrator Summing Junction This pin/pad is the summing junction for the integrator amplifier Integrator Output SAW Amplifier Inputs If only one input is used (Single-ended VCSO), the unused input should be bypassed with a capacitor to VBB. SAW Amplifier Outputs These are open collector outputs for driving the VCSO device. Operating at nominally 9 ma, external pullup resistors must be connected between these pins/pads and VCC. If only one output is used, the other output should be connected to VCC through a 50Ω resistor. PLL Output Enable The Q and Q outputs are enabled when this pin/pad is ¯ pulled high. When this pin/pad is low, the Q output is high, and the Q output is ¯ low. If the pin/pad is left open, an internal pullup resistor enables the outputs. Divide Select When this pin/pad is high, the Q and Q outputs are divided by ¯ one from the SAW device. When it is low, the Q and Q outputs are divided by ¯ two from the SAW device. If the pin/pad is left open, an internal pullup resistor selects the divide by one mode. Clock Output These pin/pads are the main clock output. When ENABLE is low, the outputs are disabled with Q high and Q low. ¯ Reference Voltage Output This pin/pad is used to bias the REFIN signal. It must be bypassed externally to the VEE pins/pads with a 0.01 μF capacitor. REFOUT Current Source If VEEP is connected to VEE, a 4 ma on-chip current ¯¯¯¯¯¯¯¯ source is provided for the ¯¯¯¯¯¯¯¯ output. REFOUT VEEP is not available on the packaged versions (AZ12010A, AZ12010B). Positive Supply +3.0 to +3.6 V Negative Supply Ground
Name REFIN
Logic Level
¯¯¯¯¯¯¯¯ REFOUT
PECL
CPREF CPOUT
CPPOL
LVCMOS LVTTL
INTREF INTSUM INTOUT SAWIN ¯¯¯¯¯¯¯ SAWIN SAWOUT SAWOUT ¯¯¯¯¯¯¯¯ ENABLE
CML (Analog) LVCMOS LVTTL LVCMOS LVTTL PECL
DIV_SEL Q Q ¯ VBB VEEP VCC VEE
November 2006 * REV - 5
www.azmicrotek.com 4
AZ12010
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol VCC VI IOUT TA TSTG Characteristic Power Supply (VEE = GND) Input Voltage (VEE = GND) — Continuous PECL Output Current — Surge Operating Temperature Range Storage Temperature Range Rating 0 to +6.0 0 to +6.0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc mA °C °C
AZ12010 DC CHARACTERISTICS (VCC = +3.0 to +3.6 V, VEE = GND)
Symbol VBB RREF RSAW VHCTL VLCTL VOH VOH VOL VOL Characteristic Reference Voltage REFIN Pull-Down resistor to VBB SAWIN, ¯¯¯¯¯¯¯ PullSAWIN Down resistor to VBB High level integrator output Low level integrator output Output HIGH Voltage
1
-40°C Min Max VCC VCC -1.38 -1.26
0°C Min VCC -1.38 Max VCC -1.26 Min VCC -1.38
25°C Typ VCC -1.31 470 10K
85°C Max VCC -1.26 Min VCC -1.38 Max VCC -1.26
Unit V Ω Ω
VCC -1.0 0.5 VCC -1085 VCC -10 VCC -1830 VCC -349 2.2 0.0 VCC -880 VCC VCC -1555 VCC -481 VCC 0.8 65
VCC -1.0 0.5 VCC -1025 VCC -10 VCC -1810 VCC -365 2.2 0.0 VCC -880 VCC VCC -1620 VCC -516 VCC 0.8 65
VCC -1.0 0.5 VCC -1025 VCC -10 VCC -1810 VCC -392 2.2 0.0 45 54 VCC -1705 VCC -449 VCC -955 VCC -880 VCC VCC -1620 VCC -557 VCC 0.8 65
VCC -1.0 0.5 VCC -1025 VCC -10 VCC -1810 VCC -465 2.2 0.0 VCC -880 VCC VCC -1620 VCC -661 VCC 0.8 65
V V mV mV mV mV V V mA
Q, Q ¯ Output HIGH Voltage2 SAWOUT, SAWOUT ¯¯¯¯¯¯¯¯ Output LOW Voltage1
2
Q, Q ¯
Output LOW Voltage SAWOUT, SAWOUT ¯¯¯¯¯¯¯¯ Input HIGH Voltage, VIH LVCMOS/LVTTL EN, DIV_SEL Input LOW Voltage, VIL LVCMOS/LVTTL EN, DIV_SEL ICC (IEE) Power Supply Current 1. Load is 50Ω to VCC-2V 2. Load is 50Ω to VCC
AZ 12010 AC CHARACTERISTICS (VCC = +3.0 to +3.6 V, VEE = GND)
Symbol Characteristic Min -40°C Typ Max Min 25° C Typ Max Min 85° C Typ Max Unit
APD fVCO t r / tf aV
Phase Detector Gain External VSCO frequency Output Rise & Fall Times (20% - 80%) Q,¯¯ Q SAW Amplifier and Driver Gain at 622.08 MHz1
20.3 800 120 18 24.5 28 15.5 21 24.5 13.5 19 22.5 800 800
radians/V MHz ps dB
1.
Single Ended Input and Output, Driven from 50Ω backmatched source, Load 50Ω to VCC.
November 2006 * REV - 5
www.azmicrotek.com 5
AZ12010
Loop Filter Design The combination of the phase detector, amplifier, VCO and divider form a second-order phase-locked loop. Proper selection of the loop components is important to obtain stable, low jitter operation. The loop bandwidth (or natural frequency, ωn) and damping factor (ζ) are the two major driving forces that define the loop’s response to a disturbance. The value of ζ is typically 0.7 to ensure the fastest step response consistent with no ringing. However in many oscillator application ζ may be 3 or higher to provide further phase noise reduction. ωn is chosen as a compromise between settling time, VCO jitter and reference feedthrough. These values can be computed by the following equations:
ωn =
1 N
Kφ KVCO
τ1
ζ=
τ 2ω n
2
τ 1 = R1C1 τ 2 = R2 C1
Kφ = Phase Detector Gain (20.3 radians/V) KVCO = VCO Gain (radians/sec/volt)
N = Frequency Divisor value (32)
The component definitions are shown in the figure below. R3 should be equal to R1 to minimize integrator offsets.
C1
R1
R2
EXTERNAL VCSO CONTROL VOLTAGE
R3
CPREF CPOUT
INTREF INTSUM INTEGRATOR
INTOUT
CHARGE PUMP
Figure 1 Charge Pump and Integrator
November 2006 * REV - 5
www.azmicrotek.com 6
AZ12010
Application Circuit A typical application circuit is shown in Figure 2.
VCC
C1
R1
R2
CPPOL CPOUT CPREF VCC
R3
INTREF INTSUM
INTOUT
ENABLE CONT OUTPT DRVR 4mA CHARGE PUMP
ENABLE
REFOUT
INTEGRATOR
DIV_SEL
VEEP MUX REFIN INPUT RCVR
Q PLL OUTPUT Q
PHASE/ FREQ DETECT SAWOUT SAW RCVR SAW DRIVE SAWOUT
R4
R5
470 Ω
VBB
VBB
C2 0.01 μF
/16
/2
F
VEE
2 x 10kΩ
SAWIN SAWIN
C3 0.01 μF
GROUND
SAW RESONATOR W/ MATCHING & TUNING NETWORK
Figure 2. Typical Application, Always Enabled and Divide by One for Output
November 2006 * REV - 5
www.azmicrotek.com 7
AZ12010 PACKAGE DIAGRAM MLP 16
NOTES NOTES DIMENSIONING AND TOLERANCING 1. 1. DIMENSIONINGTO ASME T14-1994. CONFORM AND TOLERANCING CONFORM TO ASME T14-1994. 2. THE TERMINAL #1 AND PAD 2. THE NUMBERING CONVENTION SHALL TERMINAL #1 AND PAD NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. CONFORM TO JESD 95-1 SPP-012. 3. DIMENSION b APPLIES TO METALLIZED 3. DIMENSION b APPLIES TO METALLIZED0.25 PAD AND IS MEASURED BETWEEN PAD AND 0.30mm FROM PAD TIP. 0.25 AND IS MEASURED BETWEEN AND 0.30mm FROM APPLIES 4. COPLANARITYPAD TIP. TO THE 4. COPLANARITY APPLIES TO THE THE EXPOSED PAD AS WELL AS EXPOSED PAD AS WELL AS THE TERMINALS. TERMINALS.
MILLIMETERS DIMMILLIMETERS MIN MAX DIMA MIN.80 MAX 0 1.00 A A1 0.80 .00 1.10 0 0.05 0.05 A1 A3 0.00 0.25 REF 00.18REF 0.30 .25 A3 b b D 0.225 3.90 0.275 4.10 D D2 2.90 .65 3.10 2 2.95 D2 E 1.65 .90 1.95 3 4.10 E E2 2.90 .65 3.10 2 2.95 1.95 E2 e 1.65 0.50 BSC 00.35BSC 0.45 .50 eL L aaa 0.35 00.45 .25 0.25 .10 aaa bb 0 b 0.10 .10 bbb cc 0 c 0.10 ccc November 2006 * REV - 5 www.azmicrotek.com 8
AZ12010
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
November 2006 * REV - 5
www.azmicrotek.com 9