AH3763Q-W-7

AH3763Q Q HIGH-VOLTAGE, HIGH-SENSITIVITY AUTOMOTIVE HALL-EFFECT LATCH PRELIMINARY - CONFIDENTIAL Description Pin Assignments The AH3763Q is an AEC-Q100 qualified high-voltage, high-sensitivity Hall-Effect latch IC designed for brushless DC-motor commutation speed measurement, angular or linear encoders and position sensors in automotive applications. To support a wide range of demanding applications, the design is optimized to operate over the supply range of 3.0V to 28V. With chopper stabilized architecture and an internal bandgap regulator to provide temperature compensated supply for internal circuits, the AH3763Q provides a reliable solution over the whole operating range. For robustness and protection, the device has a reverse blocking diode with a Zener clamp on the supply. The output has an overcurrent limit and a Zener clamp. (Top View) 3 OUTPUT GND 2 1 VDD SC59 and SOT23 The single, open-drain output can be switched on with South pole of sufficient strength and switched off with North pole of sufficient strength. When the magnetic flux density (B) perpendicular to the package is larger than the operate point (Bop) the output is switched (Top View) on (pulled low). The output is held latched until magnetic flux density reverses and becomes lower than the release point (Brp). 3. OUTPUT The magnetic operating and release polarity is opposite for SOT23 and SC59 packages. SOT23 and SIP-3 packages will require south pole to the part marking side to operate while SC59 will require south pole to the non part-marking side. 1. VDD 2. GND SIP-3 Features Applications • • Bipolar Latch Operation (South Pole: On, North Pole: off) High Sensitivity: Bop and Brp of +30G and -30G Typical • • • Single Open-Drain Output with Overcurrent Limit 3.0V to 28V Operating Voltage Range Chopper Stabilized Design Provides  Superior Temperature Stability  Minimal Switch Point Drift  Enhanced Immunity to Stress Good RF Noise Immunity Reverse Blocking Diode Zener Clamp on Supply and Output Pins -40°C to +150°C Operating Temperature ESD: HBM ＞8kV, CDM: >2kV AEC-Q100 Grade 0 Qualified Industry Standard SC59, SOT23 and SIP-3 Packages Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) • • • • • • • • • • • •   Notes: Brushless DC-Motor Commutation Revolution Per Minute (RPM) Measurement Angular and Linear Encoder and Position Sensing and Indexing Flow Meters Contactless Commutation, Speed Measurement and Angular Position Sensing/Indexing in Automotive Applications 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain Bop, (Note 10 ) IDD = 5mA 7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10us typical from the operating voltage reaching 3V. 8. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization. 9. Guaranteed by design, process control and characterization. Not tested in production. 10. The device will limit the output current IOUT to current limit of IOCL. AH3763Q Document number: DS38072 Rev. 2 - 2 3 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Symbol Parameter Bops (South pole to part marking side for SOT23 and SIP-3 packages; South pole to the non-part marking side for SC59 package. See diagram below) Operation Point Conditions VDD = 12V, TA = +25°C TA = -40°C to +150°C Release Point VDD = 12V, TA = +25°C TA = -40°C to +150°C Brps (North pole to part marking side for SOT23 and SIP-3 packages; North pole to the non-part marking side for SC59 package. See diagram below) Notes: VDD = 12V, TA = +25°C TA = -40°C to +150°C Hysteresis (Note 13) Bhy (|Bopx|-|Brpx|) (1mT=10 Gauss) Max Unit - Min - Typ 30 15 30 45 - -30 - -45 -30 -15 30 60 60 90 Gauss 11. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10µs typical from the operating voltage reaching 3V. 12. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization. 13. Maximum and minimum hysteresis is guaranteed by design, process control and characterization. Output VDD (off-state) ( Output Voltage ) PRELIMINARY - CONFIDENTIAL Magnetic Characteristics (Notes 11 &12) (TA = -40°C to +150°C, VDD = 3.0V to 28V, unless otherwise specified) Bhy Turn off Turn on (on-state) VOUT_ON = VSAT Brp 0 Bop ( Magnetic Flux Density B ) S S S Part mark Part mark Part mark AH3763Q Document number: DS38072 Rev. 2 - 2 N N N (SC59) (SOT23) (SIP-3) 4 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Typical Operating Characteristics TA = +25o C Hyst Bop Gauss (G) Gauss (G) 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 Brp 2 4 6 8 10 12 14 16 18 20 22 24 26 28 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 VDD = 3V Bop Brp -50 30 Hyst -25 0 25 Hyst Bop Gauss (G) Gauss (G) VDD = 12V Brp -50 -25 0 25 50 75 75 100 125 150 175 Switch Points Bop and Brp vs Temperature Switch Points Bop and Brp vs Supply Voltage 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 50 Temperature (oC) Supply Voltage (V) 100 125 150 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 175 VDD = 28V Hyst Bop Brp -50 -25 0 25 50 75 100 125 150 Temperature (oC) Temperature (oC) Switch Points Bop and Brp vs Temperature Switch Points Bop and Brp vs Temperature 175 Supply Current 4.0 5.0 TA = +25 C Supply Current IDD (mA) Supply Current IDD (mA) PRELIMINARY - CONFIDENTIAL Output Switch Operate and Release Points (Magnetic Thresholds) – Bop and Brp 4.0 3.0 2.0 1.0 3.8 3.5 28V 3.3 12V 3.0 2.8 5V 3V 2.5 2.3 2.0 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 -50 25 50 75 100 125 150 175 Supply Current vs Temperature Supply Current vs Supply Voltage Document number: DS38072 Rev. 2 - 2 0 Temperature (oC) Supply Voltage (V) AH3763Q -25 5 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Typical Operating Characteristics (cont.) TA = +25 C 2.8 2.5 2.3 2.0 1.8 1.5 1.3 1.0 0.8 0.5 0.3 0.0 -30 -28 -26 -24 -22 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 Reverse Supply Current IDD_R (mA) Reverse Supply Current IDD_R (mA) 3.0 1,200 1,050 900 -28V 750 -24V 600 450 300 -18V 150 0 -50 -25 0 25 50 75 100 125 150 175 o Supply Voltage (V) Temperature ( C) Reverse Supply Current vs Supply Voltage Reverse Supply Current vs Temperature 0.40 TA = +25 C Output ON Voltage VOUT_ON (V) Output ON Voltage VOUT_ON (V) Output Switch On Voltage 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0.40 0.35 28V 0.30 0.25 0.20 12V 5V 0.15 3V 0.10 0.05 0.00 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 -50 -25 0 25 Supply Voltage (V) 50 75 100 125 150 175 Temperature (oC) Output ON Voltage vs Supply Voltage Output ON Voltage vs Temperature 60 Output Leakage Current ILKG (nA) Output Switch Leakage Current Output Leakage Current ILKG (nA) PRELIMINARY - CONFIDENTIAL Reverse Supply Current TA = +25 C 55 50 45 40 35 30 25 20 15 10 5 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 800 700 600 28V 500 400 300 200 12V 100 3V 0 -50 25 50 75 100 125 150 175 Output Leakage Current vs Temperature Output Leakage Current vs Supply Voltage Document number: DS38072 Rev. 2 - 2 0 Temperature (oC) Supply Voltage (V) AH3763Q -25 5V 6 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Typical Operating Characteristics (cont.) 70 Output Current Limit IOCL (mA) Output Current Limit IOCL (mA) PRELIMINARY - CONFIDENTIAL Output Current Limit TA = +25 C 60 50 40 30 20 10 0 70 60 28V 50 40 3V 30 12V 5V 20 10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 -50 Supply Voltage (V) Document number: DS38072 Rev. 2 - 2 0 25 50 75 100 125 150 175 o Temperature ( C) Output Current Limit vs Supply Voltage AH3763Q -25 Output Current Limit vs Temperature 7 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Thermal Performance Characteristics Package type: SC59 and SOT23 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 230 184 166 147 129 120 110 92 83 74 55 46 37 18 0 Power Dissipation Curve 300 Power Dissipation PD (mW) PRELIMINARY - CONFIDENTIAL (1) 200 100 0 -40 0 25 50 75 100 Ambient Temperature TA (2) 125 150 (oC) Package type: SIP-3 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 550 440 396 362 308 286 264 220 198 176 132 110 88 44 0 PD (mW) Power Dissipation Curve 600 500 400 300 200 100 0 -40 0 25 50 75 100 125 150 TA (°C) AH3763Q Document number: DS38072 Rev. 2 - 2 8 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q PRELIMINARY - CONFIDENTIAL Ordering Information AH3763Q - XXX - X Packing Package 7 : Tape & Reel A: Ammo Box (Note 14) B: Bulk (Note 15) P : SIP-3 SA : SOT23 W : SC59 7” Tape and Reel Part Number Quantity Suffix Bulk Part Number Suffix Part Number Package Code Packaging Quantity AH3763Q-P-A AH3763Q-P-B P P SIP-3 SIP-3 NA 1,000 NA -B NA NA NA NA AH3763Q-SA-7 SA SOT23 NA NA 3,000/Tape & Reel AH3763Q-W-7 W SC59 NA NA 3,000/Tape & Reel Notes: Ammo Box Quantity Part Number Suffix -7 4,000/Box NA NA -A NA NA -7 NA NA 14. Ammo Box is for SIP-3 Spread Lead. 15. Bulk is for SIP-3 Straight Lead. Marking Information (1) Package Type: SC59 and SOT23 (Top View) XX Y W X Part Number AH3763Q AH3763Q (2) XX : Identification code Y : Year 0 to 9 W : Week : A to Z : 1 to 26 week; a to z : 27 to 52 week; z represents 52 and 53 week X : Internal code Package SC59 SOT23 Identification Code YM WM Package Type: SIP-3 (Top View) Part Number 3763Q Y WW X Part Number AH3763Q AH3763Q Document number: DS38072 Rev. 2 - 2 Y : Year : 0~9 WW : Week : 01~52, "52" represents 52 and 53 week X : Internal Code Package SIP-3 9 of 15 www.diodes.com Identification Code 3763Q July 2015 © Diodes Incorporated AH3763Q Q Package Outline Dimensions (All dimensions in mm.) (1) Package Type: SC59 SC59 Dim Min Max Typ A 0.35 0.50 0.38 B 1.50 1.70 1.60 C 2.70 3.00 2.80 D 0.95 G 1.90 H 2.90 3.10 3.00 J 0.013 0.10 0.05 K 1.00 1.30 1.10 L 0.35 0.55 0.40 M 0.10 0.20 0.15 N 0.70 0.80 0.75 0° 8°  All Dimensions in mm A B C G H K J M N L D 0.10/0.20 CL PART MARKING SURFACE 0.595/0.715 Min/Max 0.7/0.9 PRELIMINARY - CONFIDENTIAL Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. Die Hall Sensor Pin1 1.3/1.5 Sensor Location AH3763Q Document number: DS38072 Rev. 2 - 2 10 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. Package Type: SOT23 All 7° H K1 J K SOT23 Dim Min Max Typ A 0.37 0.51 0.40 B 1.20 1.40 1.30 C 2.30 2.50 2.40 D 0.89 1.03 0.915 F 0.45 0.60 0.535 G 1.78 2.05 1.83 H 2.80 3.00 2.90 J 0.013 0.10 0.05 K 0.890 1.00 0.975 K1 0.903 1.10 1.025 L 0.45 0.61 0.55 L1 0.25 0.55 0.40 M 0.085 0.150 0.110 a 8° All Dimensions in mm GAUGE PLANE 0.25 a M A L C L1 B D F G 0.17/0.37 Min/Max PART MARKING SURFACE 0.5/0.7 PRELIMINARY - CONFIDENTIAL (2) Die Hall Sensor Pin1 1.4/1.5 Sensor Location – To be updated AH3763Q Document number: DS38072 Rev. 2 - 2 11 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. Package Type: SIP-3 Bulk (Sensor location to be added) SIP-3 (Bulk) Dim Min Max A 3.9 4.3 a1 5° Typ a2 5° Typ a3 45° Typ a4 3° Typ B 2.8 3.2 C 1.40 1.60 D 0.33 0.432 E 0.40 0.508 F 0 0.2 G 1.24 1.30 H 2.51 2.57 J 0.35 0.43 L 14.0 15.0 N 0.63 0.84 P 1.55 All Dimensions in mm L a1 J a2 B P N D C A a3 E a4 G H F Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 1.05/1.25 PART MARKING SURFACE Hall Sensor 1 2 Die PRELIMINARY - CONFIDENTIAL (3) PART MARKING SURFACE 3 Sensor Location – To be updated AH3763Q Document number: DS38072 Rev. 2 - 2 12 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. Package Type: SIP-3 Ammo Pack N D EF SIP-3 (Ammo Pack) Dim Min Max A 3.9 4.3 a1 45° Typ a2 3° Typ B 2.8 3.2 C 1.40 1.60 D 0.35 0.41 E 0.43 0.48 F 0 0.2 G 2.4 2.9 N 0.63 0.84 P 1.55 All Dimensions in mm C A G a1 a2 B P Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 1.05/1.25 PART MARKING SURFACE Hall Sensor 1 2 Die PRELIMINARY - CONFIDENTIAL (4) PART MARKING SURFACE 3 Sensor Location – To be updated AH3763Q Document number: DS38072 Rev. 2 - 2 13 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q Suggested Pad Layout PRELIMINARY - CONFIDENTIAL Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. (1) Package Type: SC59 Y Z X (2) Dimensions Value (in mm) Z 3.4 X 0.8 Y 1.0 C 2.4 E 1.35 C E Package Type: SOT23 Dimensions Value (in mm) Z 2.9 X 0.8 Y 0.9 C 2.0 E 1.35 AH3763Q Document number: DS38072 Rev. 2 - 2 14 of 15 www.diodes.com July 2015 © Diodes Incorporated AH3763Q Q PRELIMINARY - CONFIDENTIAL IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2015, Diodes Incorporated www.diodes.com AH3763Q Document number: DS38072 Rev. 2 - 2 15 of 15 www.diodes.com July 2015 © Diodes Incorporated