AH3772-W-7

AH3772 HIGH-VOLTAGE, HIGH-SENSITIVITY HALL EFFECT LATCH PRELIMINARY - CONFIDENTIAL Description Pin Assignments The AH3772 is a high-voltage, high-sensitivity Hall Effect latch IC designed for commutation of brushless DC motors, flow meters, linear encoders, and position sensors in industrial and consumer home appliances and personal care applications. To support a wide range of demanding applications, the design is optimized to operate over the supply range of 3.0V to 28V. With chopper-stabilized architecture and an internal bandgap regulator to provide temperature compensated supply for internal circuits, the AH3772 provides a reliable solution over the whole operating range. For robustness and protection, the device has a reverse-blocking diode with a zener clamp on the supply. The output has an overcurrent limit and a zener clamp. (Top View) 3 OUTPUT GND 2 1 VDD SC59 and SOT23 (Top View) The single open-drain output can be switched on with South pole of sufficient strength and switched off with North pole of sufficient strength. When the magnetic-flux density (B) perpendicular to the package is larger than the operate point (BOP), the output is switched 3. OUTPUT 2. GND 1. VDD on (pulled low). The output is held latched until magnetic-flux density reverses and becomes lower than the release point (BRP). SIP-3 Features Applications • Bipolar Latch (South Pole: On, North Pole: Off) • 3.0V to 28V Operating Voltage Range • High Sensitivity: BOP and BRP of +25G and -25G Typical • Single, Open-Drain Output with Overcurrent Limit • Chopper-Stabilized Design Provides • • • • • - Superior Temperature Stability - Minimal Switch-Point Drift - Enhanced Immunity to Stress • Good RF Noise Immunity • Reverse-Blocking Diode and Zener Clamp on Supply • -40C to +125°C Operating Temperature • ESD (HBM): 6kV • Industry Standard SC59, SOT23 and SIP-3 Packages • Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) • Halogen and Antimony Free. “Green” Device (Note 3) Notes: Brushless DC Motor Commutation Revolution Per Minute (RPM) Measurement Flow Meters Angular and Linear Encoder and Position Sensors Contactless Commutation, Speed Measurement, and Angular Position Sensing/Indexing in Consumer Home Appliances, Office Equipment, and Industrial Applications 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. 2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain BOP, (Note 10 ) IDD = 5mA 30 28 — — 55 — mA V 7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10µs typical from the operating voltage reaching 3V. 8. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization 9. Guaranteed by design, process control, and characterization. Not tested in production. 10. The device limits the output current IOUT to current limit of IOCL. AH3772 Document number: DS38106 Rev. 2 - 2 3 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Magnetic Characteristics (Notes 11 &12) (TA = -40°C to +125°C, VDD = 3.0V to 28V, unless otherwise specified) BOP (South pole to part-marking side) BRP (North pole to part-marking side) BHY (|BOPX| - |BRPX|) Notes: Parameter (1mT=10 Gauss) Max Unit Conditions Min Typ VDD = 12V, TA = +25°C — 25 — TA = -40°C to +125°C 10 25 40 VDD = 12V, TA = +25°C — -25 — TA = -40°C to +125°C -40 -25 -10 VDD = 12V, TA = +25°C — 50 — TA = -40°C to +125°C 20 50 80 Operation Point Gauss Release Point Hysteresis (Note 13) 11. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10µs typical from the operating voltage reaching 3V. 12. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control, and characterization. 13. Maximum and minimum hysteresis is guaranteed by design, process control, and characterization. Output VDD (off-state) ( Output Voltage ) PRELIMINARY - CONFIDENTIAL Symbol Bhy Turn off Turn on (on-state) VOUT_ON = VOUT(SAT) Brp 0 Bop ( Magnetic Flux Density B ) S S S Part mark Part mark Part mark AH3772 Document number: DS38106 Rev. 2 - 2 N N SC59 SOT23 4 of 14 www.diodes.com N SIP-3(Ammo Pack) SIP-3(Bulk Pack) April 2018 © Diodes Incorporated AH3772 Typical Operating Characteristics 60.0 60.0 TA = +25oC 50.0 Hyst Hyst 40.0 30.0 30.0 Bop 20.0 Gauss (G) Gauss (G) VDD = 3V 50.0 40.0 10.0 0.0 -10.0 -20.0 Brp Bop 20.0 10.0 0.0 -10.0 -20.0 Brp -30.0 -30.0 -40.0 -50.0 -60.0 -40.0 -50.0 -60.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 -50 30 -25 0 25 100 125 150 Temperature ( C) VDD = 12V Switch Points BOP and BRP vs Temperature 60.0 Hyst VDD = 28V 50.0 Hyst 40.0 40.0 30.0 Bop 20.0 Gauss (G) Gauss (G) 75 Switch Points Bop and Brp vs Temperature Switch Points Bop andBBrp vs Supply Supply Voltage Switch Points BOP and Voltage RP vs 60.0 50 o Supply Voltage (V) 0.0 -20.0 Brp Bop 20.0 10.0 0.0 -10.0 -20.0 Brp -30.0 -40.0 -40.0 -50.0 -60.0 -60.0 -50 -25 0 25 50 75 100 125 -50 150 -25 0 25 50 75 100 125 150 Temperature (oC) Temperature (oC) Switch Points Bop and Brp vs Temperature Switch Points BOP and BRP vs Temperature Switch Points Brp Temperature Switch Points BOPBop andand BRP vsvsTemperature Supply Current 4.0 5.0 TA = +25 C Supply Current IDD (mA) Supply Current IDD (mA) PRELIMINARY - CONFIDENTIAL Magnetic Operating Switch Points—BOP and BRP 4.0 3.0 2.0 1.0 3.8 3.5 28V 3.3 3.0 2.8 3V 2.5 12V 2.3 2.0 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 -50 -40 -30 -20 -10 Supply Current vs Temperature Supply CurrentvsvsSupply Supply Voltage Voltage Supply Current Document number: DS38106 Rev. 2 - 2 10 20 30 40 50 60 70 80 90 100 110 120 130 Temperature (oC) Supply Voltage (V) AH3772 0 Supply Current vs Temperature 5 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Typical Operating Characteristics (continued) TA = +25 C Output On Voltage VOUT_ON (V) Output On Voltage VOUT_ON (V) 0.4 0.3 0.2 0.1 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 0.4 28V 0.3 0.2 12V 3V 0.1 0.0 30 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 Temperature (oC) Supply Voltage (V) Output OnOn Voltage Voltage Output Voltagevs vs Supply Supply Voltage Output Voltagevsvs Temperature Output On Voltage Temperature 30.0 Output Leakage Current (nA) Output Leakage Current (nA) Output Switch Leakage Current TA = +25 C 25.0 20.0 15.0 10.0 5.0 300 275 250 225 200 175 28V 150 125 100 12V 75 3V 50 25 0 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 -50 30 -25 0 25 50 75 100 125 150 o Temperature ( C) Supply Voltage (V) Output LeakageCurrent Current vs Output Leakage vsTemperature Temperature Leakage Current Supply Voltage OutputOutput Leakage Current vs vs Supply Voltage Supply Reverse Current 3.0 2.8 750 TA = +25 C Supply Reverse Current (mA) Supply Reverse Current (mA) PRELIMINARY - CONFIDENTIAL Output Switch On Voltage 2.5 2.3 2.0 1.8 1.5 1.3 1.0 0.8 0.5 0.3 0.0 -30 -28 -26 -24 -22 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 625 -28V 500 -24V 375 250 -18V 125 0 -50 25 50 75 100 125 150 Supply Reverse Current vs Temperature Supply Reverse Current vs Temperature Supply Reverse Current Supply Voltage Supply Reverse Current vs vs Supply Voltage Document number: DS38106 Rev. 2 - 2 0 Temperature (oC) Supply Voltage (V) AH3772 -25 6 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Thermal Performance Characteristics Package types: SOT23 and SC59 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 230 184 166 147 129 120 110 92 83 74 55 46 37 18 0 Power Dissipation Curve 300 Power Dissipation PD (mW) PRELIMINARY - CONFIDENTIAL (1) 200 100 0 0 -40 25 50 75 100 125 150 Ambient Temperature TA (oC) (2) Package type: SIP-3 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 550 440 396 362 308 286 264 220 198 176 132 110 88 44 0 PD (mW) Power Dissipation Curve 600 500 400 300 200 100 0 0 -40 25 50 75 100 125 150 TA (°C) AH3772 Document number: DS38106 Rev. 2 - 2 7 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Ordering Information PRELIMINARY - CONFIDENTIAL AH3772 - XXX - X Packing Package 7 : Tape & Reel A: Ammo Box (Note 14) B: Bulk (Note 15) P : SIP-3 SA : SOT23 W : SC59 7” Tape and Reel Part Number Quantity Suffix Bulk Part Number Suffix Ammo Box Quantity Part Number Suffix Part Number Package Code Packaging AH3772-P-A P SIP-3 — — — — 4000/Box -A AH3772-P-B P SIP-3 1000 -B — — — — AH3772-SA-7 SA SOT23 — — 3000/Tape & Reel -7 — — AH3772-W-7 W SC59 — — 3000/Tape & Reel -7 — — Notes: Quantity 14. Ammo Box is for SIP-3 Spread Lead. 15. Bulk is for SIP-3 Straight Lead. Marking Information (1) Package Type: SOT23 and SC59 ( Top View ) XX Y W X (2) XX : Identification code Y : Year 0 to 9 W : Week : A to Z : 1 to 26 week; a to z : 27 to 52 week; z represents 52 and 53 week X : Internal code Part Number Package Identification Code AH3772 AH3772 SOT23 SC59 WV YV Package Type: SIP-3 ( Top View ) Part Number 3772 Y WW X Part Number AH3772 AH3772 Document number: DS38106 Rev. 2 - 2 Y : Year : 0~9 WW : Week : 01~52, "52" represents 52 and 53 week X : Internal Code Package SIP-3 8 of 14 www.diodes.com Identification Code 3772 April 2018 © Diodes Incorporated AH3772 Package Outline Dimensions (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. Package Type: SOT23 All 7° H K1 J K SOT23 Dim Min Max Typ A 0.37 0.51 0.40 B 1.20 1.40 1.30 C 2.30 2.50 2.40 D 0.89 1.03 0.915 F 0.45 0.60 0.535 G 1.78 2.05 1.83 H 2.80 3.00 2.90 J 0.013 0.10 0.05 K 0.890 1.00 0.975 K1 0.903 1.10 1.025 L 0.45 0.61 0.55 L1 0.25 0.55 0.40 M 0.085 0.150 0.110 a 0° 8° -All Dimensions in mm GAUGE PLANE 0.25 a M A L C L1 B D F G 0.17/0.37 Min/Max PART MARKING SURFACE 0.5/0.7 PRELIMINARY - CONFIDENTIAL (1) Die Hall Sensor Pin1 1.4/1.5 Sensor Location AH3772 Document number: DS38106 Rev. 2 - 2 9 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Package Outline Dimensions (cont.) (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. Package Type: SC59 PRELIMINARY - CONFIDENTIAL (2) A SC59 Dim Min Max Typ A 0.35 0.50 0.38 B 1.50 1.70 1.60 C 2.70 3.00 2.80 D 0.95 G 1.90 H 2.90 3.10 3.00 J 0.013 0.10 0.05 K 1.00 1.30 1.10 L 0.35 0.55 0.40 M 0.10 0.20 0.15 N 0.70 0.80 0.75 0° 8°  All Dimensions in mm B C G H K J M N D L 0.17/0.37 Min/Max 0.5/0.7 PART MARKING SURFACE Die Hall Sensor Pin1 1.4/1.5 Sensor Location AH3772 Document number: DS38106 Rev. 2 - 2 10 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Package Outline Dimensions (continued) (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. Package Type: SIP-3 Bulk a4 ( a3( 2x 2x S ) a1 ( A 2x J ( 2x ) D SIP-3 (Bulk Pack) Dim Min Max Typ A 1.40 1.60 1.50 b 0.33 0.43 0.38 b2 0.40 0.508 0.46 c 0.35 0.41 0.38 D 3.90 4.30 4.10 E 2.80 3.20 3.00 e1 1.24 1.30 1.27 F 0.00 0.20 -J 2.62 REF L 14.00 15.00 14.50 L1 1.55 1.75 1.65 S 0.63 0.84 0.74 -a1 -5 -a2 -5 -a3 -45 -a4 -3 All Dimensions in mm a2 E b2 L1 F L e1 b c Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 1.05/1.25 PART MARKING SURFACE Hall Sensor 1 2 Die PRELIMINARY - CONFIDENTIAL (3) PART MARKING SURFACE 3 Sensor Location AH3772 Document number: DS38106 Rev. 2 - 2 11 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Package Outline Dimensions (cont.) (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. Package Type: SIP-3 Ammo Pack a4 ( a3( ) 2x SIP-3 (Ammo Pack) Dim Min Max Typ A 1.40 1.60 1.50 b 0.33 0.43 0.38 b2a 0.40 0.52 0.46 c 0.35 0.41 0.38 D 3.90 4.30 4.10 E 2.80 3.20 3.00 e1 1.24 1.30 1.27 e2 2.40 2.90 2.65 F 0.00 0.20 — J 2.62 REF L 14.00 15.00 14.50 La 12.90 14.90 13.90 L1 1.55 1.75 1.65 L3 2.00 3.00 2.50 S 0.63 0.84 0.74 — — a1 5 — — a2 5 — — a3 45 — — a4 3 All Dimensions in mm S D ( A J ) 2x a1 ( 2x 2x a2 E L3 b2a L1 F e1 La L c e2 b Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 1.05/1.25 PART MARKING SURFACE Hall Sensor 1 2 Die PRELIMINARY - CONFIDENTIAL (4) PART MARKING SURFACE 3 Sensor Location AH3772 Document number: DS38106 Rev. 2 - 2 12 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 Suggested Pad Layout PRELIMINARY - CONFIDENTIAL Please see http://www.diodes.com/package-outlines.html for the latest version. (1) Package Type: SOT23 Y C Y1 X (2) Dimensions Value (in mm) C 2.0 X 0.8 X1 1.35 Y 0.9 Y1 2.9 X1 Package Type: SC59 Y Z Dimensions Value (in mm) Z 3.4 X 0.8 Y 1.0 C 2.4 E 1.35 C X AH3772 Document number: DS38106 Rev. 2 - 2 E 13 of 14 www.diodes.com April 2018 © Diodes Incorporated AH3772 PRELIMINARY - CONFIDENTIAL IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2018, Diodes Incorporated www.diodes.com AH3772 Document number: DS38106 Rev. 2 - 2 14 of 14 www.diodes.com April 2018 © Diodes Incorporated