Data sheet
Single Phase Synchronous Buck PWM Controller
General Description
Features
The AP3586A/B/C is a compact synchronous
-rectified buck controller specifically designed to
operate from 5V or 12V supply voltage and deliver
high-quality output voltage as low as 0.6V
(AP3586A) or 0.8V (AP3586B/C). This device
operates at fixed 300kHz (AP3586A/B) or 200kHz
(AP3586C) frequency and provides an optimal level
of integration to reduce size and cost of the power
supply.
•
•
•
•
•
•
•
•
•
This controller integrates internal MOSFET drivers
that support 12V+12V bootstrapped voltage for highefficiency power conversion. The bootstrap diode is
built-in to simplify the circuit design and minimize
external part count.
•
•
•
•
•
•
•
•
•
This controller provides single feedback loop,
voltage-mode control with fast transient response.
The error amplifier features a 10MHz gain-bandwidth
product and 6V/µs slew rate which enables high
converter bandwidth for fast transient performance.
Other features include internal soft-start, under
voltage protection, over current protection and
shutdown function. With afore-mentioned functions,
this part provides customers a compact, high
efficiency,
well-protected
and
cost-effective
solutions.
AP3586A/B/C
Supply Voltage: 5V/12V
VIN Input Range: 3.3V to 12V
0.6V/0.8V to 82% of VIN Output Range
Internal Reference: 0.6V/0.8V
Simple Single-loop Control
Voltage-mode PWM Control
Duty Cycle: 0% to 82%
Fast Transient Response
10MHz High-bandwidth Error Amplifier with
6V/µs Slew Rate
Fixed Oscillator Frequency: 300kHz/200kHz
Lossless, Programmable Over Current Protection
(Uses Lower MOSFET RDS(ON) )
Start-up into Pre-biased Load
Built-in Thermal Shutdown
Built-in Soft-start
Over Current Protection
Over Voltage Protection
Under Voltage Protection
Integrated Boot Diode
Applications
•
•
•
•
The AP3586A/B/C is available in SOIC-8 and
PSOP-8 packages.
•
Subsystem Power Supplies
PCI, AGP, Graphics Cards, Digital TV
SSTL-2 and DDR/2/3 SDRAM Bus Termination
Supply
Cable Modems, Set Top Boxes, and DSL
Modems
Industrial Power Supplies and General Purpose
Supplies
SOIC-8/PSOP-8
Figure 1. Package Types of AP3586A/B/C
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
1
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Pin Configuration
MP Package
(PSOP-8)
M Package
(SOIC-8)
1
8
1
8
2
7
2
7
3
6
3
6
4
5
4
5
Figure 2. Pin Configuration of AP3586A/B/C (Top View)
Pin Description
Pin Number
SOIC-8
PSOP-8
Pin Name
1
1
BOOT
2
2
UGATE
3
3
GND
4
4
LGATE/OCSET
5
5
VCC
6
6
FB
7
7
COMP/EN
8
8
PHASE
9
Exposed Pad
Mar. 2012
Function
Bootstrap pin. Connect a bootstrap capacitor from this pin to
PHASE for creating a BOOT voltage suitable to drive a standard
N-Channel MOSFET.
Upper-gate drive pin. Connect this pin to the upper MOSFET gate
providing the gate drive. This pin is monitored by the adaptive
shoot-through protection circuitry to determine when the upper
MOSFET has turned off.
Ground for the IC. All voltage levels are measured with respect to
this pin. Connect this pin directly to the low side MOSFET source
and ground plane with the lowest impedance. The exposed pad
must be soldered to a large PCB and connected to GND for
maximum power dissipation.
Low-side Gate Driver Output and Over-Current Setting Input.
This pin is the gate driver for low-side MOSFET. It is also used to
set the maximum inductor current. Refer to the section in
“Function Description” for detail.
Bias supply pin. Provides a 5V or 12V bias supply for the chip
from this pin. The pin should be bypassed with a capacitor to
GND.
Feedback pin. This pin is the inverting input of the internal error
amplifier. Use FB pin, in combination with the COMP pin, to
compensate the voltage control feedback loop of the converter. A
resistor divider from output to GND is used to set the output
voltage.
Compensation and disable pin. This pin is the output of the Error
Amplifier. Pull COMP pin low will shut down the IC.
This pin connects to the source of the upper MOSFET and the
drain of the lower MOSFET. This pin is also monitored by the
adaptive shoot-through protection circuitry to determine when the
upper MOSFET has turned off.
Exposed Pad as ground pin.
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
2
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Functional Block Diagram
5
1
2
8
4
/OCSET
/0.6V
6
3
7
/EN
Figure 3. Functional Block Diagram of AP3586A/B/C
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
3
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Ordering Information
AP3586
-
Circuit Type
G1: Green
A: AP3586A
B: AP3586B
C: AP3586C
Blank: Tube
TR: Tape & Reel
Package
M: SOIC-8
MP: PSOP-8
Package
Temperature
Range
SOIC-8
-40 to 85°C
PSOP-8
Part Number
Marking ID
Packing Type
AP3586AM-G1
3586AM-G1
Tube
AP3586AMTR-G1
3586AM-G1
Tape & Reel
AP3586BM-G1
3586BM-G1
Tube
AP3586BMTR-G1
3586BM-G1
Tape & Reel
AP3586CM-G1
3586CM-G1
Tube
AP3586CMTR-G1
3586CM-G1
Tape & Reel
AP3586AMP-G1
3586AMP-G1
Tube
AP3586AMPTR-G1
3586AMP-G1
Tape & Reel
AP3586BMP-G1
3586BMP-G1
Tube
AP3586BMPTR-G1
3586BMP-G1
Tape & Reel
AP3586CMP-G1
3586CMP-G1
Tube
AP3586CMPTR-G1
3586CMP-G1
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant
and green.
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
4
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Value
Unit
VCC
-0.3 to 15
V
BOOT Voltage
VBOOT
-0.3 to VPHASE +15
V
UGATE to PHASE Voltage
VUGATE
-0.3 to 15
V
PHASE, LGATE to GND Voltage
VPHASE,
VLGATE
-1 to 15
V
-0.3 to 6
V
Supply Input Voltage
Other Pin Voltage
Power Dissipation
PD
TBD
mW
Thermal Resistance
θJA
50
ºC/W
Operating Junction Temperature
TJ
-40 to 125
ºC
Storage Temperature
TSTG
-65 to 150
ºC
Lead Temperature (Soldering, 10 sec)
TLEAD
260
ºC
ESD (Human Body Model) (Note 2)
2000
V
ESD (Machine Model) (Note 2)
200
V
Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute
Maximum Ratings” for extended periods may affect device reliability.
Note 2: Devices are ESD sensitive. Handling precaution is recommended.
Recommended Operating Conditions
Parameter
Symbol
Min
Max
Unit
Supply Input Voltage
VCC
5
12
V
Operating Ambient Temperature
TA
-40
85
°C
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
5
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Electrical Characteristics
VCC=12V, TA=25°C, unless otherwise specified.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
SUPPLY INPUT
ICC
Supply Current
Quiescent Supply Current
ICC_Q
Power Input Voltage
VIN
UGATE and LGATE
Open; Switching
VFB=VREF+0.1V,
No Switching
Pins
5
mA
4
mA
3.0
13.2
V
4.4
V
POWER ON RESET
VCC Rising Threshold
VPOR
VCC Threshold Hysteresis
VCC Rising
4.0
VPOR_HYS
4.2
500
mV
OSCILLATOR
fOSC
Oscillator Frequency
For AP3586A/B
270
300
330
kHz
For AP3586C
180
200
220
kHz
∆VOSC
Ramp Amplitude
1.4
VP-P
70
dB
10
MHz
6
V/µs
ERROR AMPLIFIER
GDC_OL
Open Loop DC Gain
Gain-bandwidth Product
GBW
Slew Rate
SR
55
3
Transconductance
800
1100
µA/V
Output Source Current
VFBVREF
80
120
µA
-1.0
A
1.5
A
PWM CONTROLLER GATE DRIVERS
Upper
Current
Gate
Source
Upper Gate Sink Current
Upper
Gate
Resistance
Lower
Gate
Current
Sink
IUG_SRC
IUG_SNK
VBOOT-VPHASE=12V,
VBOOT-VUGATE=6V
VBOOT-VPHASE=12V,
VBOOT-VUGATE=6V
RUGATE
50mA Source Current
2
ILG_SRC
VCC-VLGATE=6V
-1
A
Lower Gate Sink Current
ILG_SNK
VLGATE=6V
1.5
A
Lower
Gate
Resistance
RLGATE
50mA Source Current
1
VPHASE1.2V
50
ns
VLGATE1.2V
50
ns
Source
Sink
PHASE Falling to LGATE
Rising Delay
LGATE Falling to UGATE
Rising Delay
Mar. 2012
Rev. 1. 1
4
2
Ω
Ω
BCD Semiconductor Manufacturing Limited
6
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Electrical Characteristics (Continued)
VCC=12V, TA=25ºC, unless otherwise specified.
Parameter
Symbol
Conditions
Min
Minimum Duty Cycle
Typ
Max
0
Maximum Duty Cycle
Unit
%
75
82
89
%
AP3586A
0.591
0.6
0.609
V
AP3586B/C
0.788
0.8
0.812
V
10
50
nA
0.4
0.5
V
REFERENCE VOLTAGE
Feedback Voltage
VFB
Feedback Bias Current
IFB
VFB=5V
PROTECTION
Under Voltage Protection
VFB_UVP
Over Voltage Protection
VFB_OVP
OC Current Source
Built-in Maximum OCP
Voltage
Soft-start Interval
Enable Threshold
0.3
1.1
IOPS
19.5
VOCP_MAX
tSS
21.5
V
23.5
0.3
AP3586A
2
AP3586B
2.7
AP3586C
3.6
VCOMP/EN
0.25
0.30
µA
V
ms
0.35
V
Thermal Shutdown
TOTSD
160
ºC
Thermal Shutdown
Hysteresis
THYS
20
ºC
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
7
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Typical Performance Characteristics
4
1.0
Output Voltage Variation (%)
Output Voltage Variation (%)
3
VOUT= 1.2V
0.5
0.0
-0.5
VOUT= 1.2V
2
1
0
-1
-2
-3
-4
-1.0
5
6
7
8
9
10
11
12
0
13
2
4
6
Input Voltage (V)
320
320
315
315
310
310
305
300
295
290
285
280
12
14
16
18
20
12
13
14
305
300
295
290
285
280
275
275
270
-20
0
20
40
60
80
100
4
120
5
6
7
8
9
10
11
Input Voltage (V)
o
Temperature ( C)
Figure 6. Switching Frequency vs. Temperature
Mar. 2012
10
Figure 5. Load Regulation
Switching Frequency (kHz)
Switching Frequency (kHz)
Figure 4. Line Regulation
270
-40
8
Output Current (A)
Figure 7. Switching Frequency vs. Input Voltage
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
8
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
0.810
0.810
0.808
0.808
0.806
0.806
Reference Voltage (V)
Reference Voltage (V)
Typical Performance Characteristics (Continued)
0.804
0.802
0.800
0.798
0.796
0.804
0.802
0.800
0.798
0.796
0.794
0.794
0.792
0.792
0.790
-40
0.790
-20
0
20
40
60
80
100
4
120
Figure 8. Reference Voltage vs. Temperature
6
7
8
9
10
11
12
13
14
Figure 9. Reference Voltage vs. Input Voltage
VIN
10V/div
IL
5A/div
VOUT
0.5V/div
VCOMP
0.5V/div
VOUT
0.5V/div
VCOMP
1V/div
VLGATE
5V/div
VLGATE
20V/div
Time 2ms/div
Time 1ms/div
Figure 10. Power-on Waveform
(VIN=12V, VOUT=1.2V, IOUT=0A)
Mar. 2012
5
Input Voltage (V)
o
Temperature ( C)
Figure 11. Enable Waveform
(VIN=12V, VOUT=1.2V, IOUT=0A)
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
9
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Typical Performance Characteristics (Continued)
VOUT_AC
50mV/div
VOUT_AC
50mV/div
IOUT
2A/div
IOUT
5A/div
Time 20µs/div
Time 20µs/div
Figure 12. Load Transient Response
(VIN=12V, VOUT=1.2V, IOUT=0A to 10A)
Figure 13. Load Transient Response
(VIN=12V, VOUT=1.2V, IOUT=0A to 20A)
VIN
10V/div
VOUT
1V/div
VUGATE
10V/div
VLGATE
20V/div
VFB
0.5V/div
VCOMP
1V/div
VLGATE
5V/div
IL
10A/div
Time 20ms/div
Time 10ms/div
Figure 15. Under Voltage Protection
(VIN=12V, VOUT=1.2V, IOUT=20A)
Figure 14. Over Current Protection
(VIN=12V, VOUT=1.2V, IOUT=20A)
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
10
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Typical Application
Figure 16. Typical Application Circuit of AP3586A/B/C
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
11
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Function Description
from power supply input VIN during turn-on
(Referring to the Functional Block Diagram). The
error amplifier is a three-input device. Reference
voltage VREF or the internal soft start voltage SS
whichever is smaller dominates the behavior of the
non-inverting inputs of the error amplifier. SS
internally ramps up to 0.6V in 2ms for AP3586A (to
0.8V in 2.7ms for AP3586B; to 0.8V in 3.6ms for
AP3586C) after the soft start cycle is initiated. The
ramp is created digitally, so there will be 100 small
discrete steps. Accordingly, the output voltage will
follow the SS signal and ramp up smoothly to its
target level.
The AP3586A/B/C is a voltage-mode single phase
synchronous buck controller with embedded
MOSFET drivers. This part provides complete
protection functions such as over voltage protection,
under voltage protection and over current protection.
Inductor current information is sensed by RDS(ON) of
the low side MOSFET. The over current protection
threshold can be simply programmed by a resistor.
Power on Reset and Chip Enable
A power on reset (POR) circuitry continuously
monitors the supply voltage at VCC pin. Once the
rising POR threshold is exceeded, the AP3586A/B/C
sets itself to active state and is ready to accept chip
enable command. The rising POR threshold is
typically 4.2V at VCC rising.
The SS signal keeps ramping up after it exceeds the
internal 0.6V (0.8V for AP3586B/C) reference
voltage. However, the internal 0.6V(0.8V for
AP3586B/C) reference voltage takes over the
behavior of error amplifier after SS>VREF. When the
SS signal climbs to its ceiling voltage (4.2V),
AP3586A/B/C claims the end of soft start cycle and
enables the under voltage protection of the output
voltage.
The COMP/EN is a multifunctional pin:
control loop compensation and chip enable as shown
in Figure 17. An Enable Comparator monitors the
COMP/EN pin voltage for chip enable. A signal level
transistor is adequate to pull this pin down to ground
and shut down AP3586. A 120µA current source
charges the external compensation network with
0.45V ceiling when this pin is released. If the voltage
at COMP/EN pin exceeds 0.3V, the AP3586A/B/C
initiates its soft start cycle.
Figure 18 shows a typical start up interval for
AP3586A/B/C where the COMP/EN pin has been
released from a grounded (system shutdown) state.
The internal 120µA current source starts charge the
compensation network after the COMP/EN pin is
released from ground at T1. The COMP/EN exceeds
0.3V and enables the AP3586A/B/C at T2. The
COMP/EN continues ramping up the stays at 0.45V
before the SS starts ramping at T3. The output
voltage follows the internal SS and ramps up to its
final level during T3 and T4. At T4, the reference
voltage VREF takes over the behavior of the error
amplifier as the internal SS crosses VREF. The internal
SS keeps ramping up and stays at 4.2V at T5, where
AP3586A/B/C asserts the end of soft start cycle.
The 120µA current source keeps charging the COMP
pin to its ceiling until the feedback loop boosts the
COMP pin higher than 0.45V according to the
feedback signal. The current source is cut off when
VCOMP is higher than 0.45V during normal operation.
Figure 17. Chip Enable Function
Soft Start
A built-in Soft Start is used to prevent surge current
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
12
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Function Description (Continued)
following equation:
VIN 10V/Div
I LIMIT =
VOUT 0.5V/Div
Because the RDS(ON) of MOSFET increases with
temperature, it is necessary to take this thermal effect
into consideration in calculating OCP point.
COMP 0.5V/Div
When OCP is triggered, both UGATE and LGATE
will go low to stop the energy transfer to the load.
Controller will try to restart in a hiccupped way.
Figure 20 shows the hiccupped over current
protection. Only four times of hiccup is allowed in
over current protection. If over current condition still
exists after four times of hiccup, controller will be
latched.
LGATE 10V/Div
1ms/Div
Figure 18. Soft Start Behavior of AP3586A/B/C
Power Input Detection
The AP3586A/B/C detects PHASE voltage for the
present of power input VIN when UGATE turns on the
first time. If the PHASE voltage does not exceed
2.0V when UGATE turns on, AP3586A/B/C asserts
that VIN is not ready and stops the soft start cycle.
However, the internal SS continues ramping up to
VDD. Another soft start is initiated after SS ramps up
to VDD. The hiccup period is about 1ms. Figure 19
shows the start-up waveform where VIN does not
present initially.
Figure 20. Hiccupped Over Current Protection
Over Voltage Protection (OVP)
The feedback voltage is continuously monitored for
over voltage protection. When OVP is triggered,
LGATE will go high and UGATE will go low to
discharge the output capacitor.
VIN 10V/Div
The AP3586A/B/C provides full-time over voltage
protection whenever soft start completes or not. The
typical OVP threshold is 137.5% of the internal
reference voltage VREF. AP3586A/B/C provides
non-latched OVP. The controller will return to normal
operation if over voltage condition is removed.
VOUT 0.5V/Div
LGATE 10V/Div
IL 10A/Div
Under Voltage Protection (UVP)
The feedback voltage is also monitored for under
voltage protection. The under voltage protection has
15µs triggered delay. When UVP is triggered, both
UGATE and LGATE will go low. Unlike OCP, UVP
is not a latched protection; controller will always try
to restart in a hiccupped way.
1ms/Div
Figure 19. Soft Start Where VIN Does Not Present
Initially
Over Current Protection (OCP)
A resistor ROCSET connected from LGATE pin sets the
threshold. An internal current source IOC(21.5µA
typically), flowing through ROCSET determines the
OCP trigger point, which can be calculated using the
Mar. 2012
2 × I OCSET × R OCSET
R DS(ON) of the low side MOSFET
Thermal Shutdown
If the junction temperature of the device reaches the
thermal shutdown limit of 160°C, the PWM and the
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
13
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Function Description (Continued)
1)
oscillator are turned off and UGATE and LGATE are
driven low, turning off both MOSFETs. When the
junction cools to the required level (140°C
nominal), the PWM initiates soft start as during a
normal power-up cycle.
Output Voltage Selection
The output voltage can be programmed to any level
between the 0.6V internal reference (0.8V for
AP3586B/C) to the 82% of VIN supply. The lower
limitation of output voltage is caused by the internal
reference. The upper limitation of the output voltage
is caused by the maximum available duty cycle
(82%). This is to leave enough time for over-current
detection. Output voltage out of this range is not
allowed.
2)
A voltage divider sets the output voltage (Refer to the
typical application circuit). In real applications,
choose R1 in 100Ω to 10kΩ range and choose
appropriate R2 according to the desired output
voltage.
VOUT = 0.6V ×
VOUT = 0.8V ×
R1 + R2
R2
R1 + R2
R2
3)
4)
AP3586A
AP3586B/C
5)
PCB Layout Considerations
High speed switching and relatively large peak
currents in a synchronous-rectified buck converter
make the PCB layout a very important part of design.
Switching current from one power device to another
can generate voltage spikes across the impedances of
the interconnecting bond wires and circuit traces. The
voltage spikes can degrade efficiency and radiate
noise, that results in over-voltage stress on devices.
Careful component placement layout a printed circuit
design can minimize the voltage spikes induced in the
converter.
6)
Follow the below layout guidelines for optimal
performance of AP3586A/B/C.
Mar. 2012
Rev. 1. 1
The turn-off transition of the upper MOSFET
prior to turn-off, the upper MOSFET was
carrying the full load current. During turn-off,
current stops flowing in the upper MOSFET and
is picked up by the low side MOSFET. Any
inductance in the switched path generates a large
voltage spike during the switching interval.
Careful component selections, layout of the
critical components, and use shorter and wider
PCB traces help in minimizing the magnitude of
voltage spikes.
The power components and the PWM controller
should be placed firstly. Place the input
capacitors, especially the high-frequency ceramic
decoupling capacitors, close to the power
switches. Place the output inductor and output
capacitors between the MOSFETs and the load.
Also locate the PWM controller near MOSFETs.
Use a dedicated grounding plane and use vias to
ground all critical components to this layer. Use
an immediate via to connect the component to
ground plane including GND of AP3586A/B/C.
Apply another solid layer as a power plane and
cut this plane into smaller islands of common
voltage levels. The power plane should support
the input power and output power nodes. Use
copper filled polygons on the top and bottom
circuit layers for the PHASE node.
The PHASE node is subject to very high dV/dt
voltages. Stray capacitance between this island
and the surrounding circuitry tend to induce
current spike and capacitive noise coupling.
Keep the sensitive circuit away from the PHASE
node and keep the PCB area small to limit the
capacitive coupling. However, the PCB area
should be kept moderate since it also acts as
main heat convection path of the lower
MOSFET.
The PCB traces between the PWM controller and
the gate of MOSFET and also the traces
connecting source of MOSFETs should be sized
to carry 2A peak currents.
BCD Semiconductor Manufacturing Limited
14
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Mechanical Dimensions
SOIC-8
4.700(0.185)
5.100(0.201)
7°
Unit: mm(inch)
0.320(0.013)
1.350(0.053)
1.750(0.069)
8°
8°
7°
0.675(0.027)
0.725(0.029)
D
5.800(0.228)
1.270(0.050)
6.200(0.244)
TYP
D
20:1
0.800(0.031)
0.300(0.012)
R0.150(0.006)
0.100(0.004)
0.200(0.008)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
0.330(0.013)
0.190(0.007)
0.250(0.010)
1°
5°
0.510(0.020)
0.900(0.035)
R0.150(0.006)
0.450(0.017)
0.800(0.031)
Note: Eject hole, oriented hole and mold mark is optional.
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
15
Data sheet
Single Phase Synchronous Buck PWM Controller
AP3586A/B/C
Mechanical Dimensions (Continued)
Unit: mm(inch)
3.202(0.126)
3.402(0.134)
PSOP-8
Mar. 2012
Rev. 1. 1
BCD Semiconductor Manufacturing Limited
16
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
IMPORTANT NOTICE
IMPORTANT
NOTICE
BCD Semiconductor
BCD
Semiconductor Manufacturing
Manufacturing Limited
Limited reserves
reserves the
the right
right to
to make
make changes
changes without
without further
further notice
notice to
to any
any products
products or
or specifispecifications herein.
cations
herein. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not assume
assume any
any responsibility
responsibility for
for use
use of
of any
any its
its products
products for
for any
any
particular purpose,
particular
purpose, nor
nor does
does BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited assume
assume any
any liability
liability arising
arising out
out of
of the
the application
application or
or use
use
of any
of
any its
its products
products or
or circuits.
circuits. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not convey
convey any
any license
license under
under its
its patent
patent rights
rights or
or
other rights
other
rights nor
nor the
the rights
rights of
of others.
others.
MAIN SITE
SITE
MAIN
- Headquarters
BCD
Semiconductor Manufacturing Limited
BCD
Semiconductor
Manufacturing Limited
- Wafer
Fab
No.
1600, Zi
Xing Road,
Shanghai ZiZhu
Science-basedLimited
Industrial Park, 200241, China
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Tel:
Fax: +86-21-24162277
800,+86-21-24162266,
Yi Shan Road, Shanghai
200233, China
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008
REGIONAL SALES OFFICE
Shenzhen OfficeSALES OFFICE
REGIONAL
- Wafer
FabSemiconductor Manufacturing Limited
BCD
Shanghai
SIM-BCD
Semiconductor Manufacturing Co., Ltd.
- IC Design
Group
800 Yi
Shan Road,
Shanghai
200233,
China Corporation
Advanced
Analog
Circuits
(Shanghai)
Tel: +86-21-6485
1491,YiFax:
0008200233, China
8F, Zone B, 900,
Shan+86-21-5450
Road, Shanghai
Tel: +86-21-6495 9539, Fax: +86-21-6485 9673
Taiwan Office
Shanghai
Semiconductor Manufacturing Co., Ltd., Shenzhen Office
BCD Taiwan
Semiconductor
Shenzhen SIM-BCD
Office
Office (Taiwan) Company Limited
Unit
A Room
1203, Skyworth
Bldg., Gaoxin
Ave.1.S., Nanshan
Shenzhen,
4F, 298-1,
Guang Road,(Taiwan)
Nei-Hu District,
Taipei,
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Co., Ltd.District,
Shenzhen
Office
BCDRui
Semiconductor
Company
Limited
China
Taiwan
Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office
4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei,
Tel:
+86-755-8826
Tel: +886-2-2656
2808
Room
E, 5F, Noble 7951
Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China
Taiwan
Fax:
+86-755-88267951
7865
Fax: +886-2-2656
28062808
Tel: +86-755-8826
Tel: +886-2-2656
Fax: +86-755-8826 7865
Fax: +886-2-2656 2806
USA Office
BCD Office
Semiconductor Corp.
USA
30920Semiconductor
Huntwood Ave.Corporation
Hayward,
BCD
CA 94544,
USA Ave. Hayward,
30920
Huntwood
Tel :94544,
+1-510-324-2988
CA
U.S.A
Fax:: +1-510-324-2988
+1-510-324-2788
Tel
Fax: +1-510-324-2788
工商网监
湘ICP备2023018690号
