AZ393_06

Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C General Description The AZ393/393C series consists of two independent precision voltage comparators with an offset voltage specification as low as 1mV. The input common mode voltage range of these comparators includes ground, even when operated from a single power supply voltage. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. The AZ393/393C series is designed to directly interface with TTL and CMOS. AZ393C has more stringent input offset voltage than AZ393. Features · Wide Supply Voltage Range - Single Supply: 2.0V to 18V - Dual Supplies: ±1.0V to ±9V Very Low Supply Current Drain: 0.4mA - Independent of Supply Voltage Low Input Bias Current: 25nA (Typical) Low Input Offset Current: ±5nA (Typical) Low Input Offset Voltage: ±1mV (Typical) Input Common Mode Voltage Range Includes Ground Differential Input Voltage Range Equals to the Power Supply Voltage Low Output Saturation Voltage: 250mV at 4mA Open Collector Output · · · · · · · · The AZ393/393C series can be widely used in applications such as battery charger, cordless telephone, switching power supply, DC-DC module and PC motherboard. The AZ393/393C series are available in standard packages of DIP-8 and SOIC-8. Applications · · · · · · Battery Charger Cordless Telephone Switching Power Supply DC-DC Module PC Motherboard Communication Equipment SOIC-8 DIP-8 Figure 1. Package Types of AZ393/393C Aug. 2006 Rev. 1. 2 1 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Pin Configuration M Package/P Package (SOIC-8/DIP-8) 1 2 3 4 8 7 6 5 OUTPUT1 INPUT1INPUT1+ GND VCC OUTPUT2 INPUT2INPUT2+ Top View Figure 2. Pin Configuration of AZ393/393C Functional Block Diagram VCC 3.5µA 100µA 3.5µA 100µA +INPUT Q2 Q1 Q3 Q4 OUTPUT -INPUT Q7 Q8 Q5 Q6 Figure 3. Functional Block Diagram of AZ393/393C (Each Comparator) Aug. 2006 Rev. 1. 2 2 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Ordering Information AZ393 E1: Lead Free Blank: Tin Lead TR: Tape and Reel Blank: Tube Circuit Type Blank: AZ393 C: AZ393C Package M: SOIC-8 P: DIP-8 Package Input Offset Voltage 5mV Part Number Tin Lead AZ393M AZ393MTR AZ393CM AZ393CMTR AZ393P AZ393CP Lead Free AZ393M-E1 AZ393MTR-E1 AZ393CM-E1 AZ393CMTR-E1 AZ393P-E1 AZ393CP-E1 Marking ID Tin Lead AZ393M AZ393M 393CM 393CM AZ393P AZ393CP Lead Free AZ393M-E1 AZ393M-E1 393CM-E1 393CM-E1 AZ393P-E1 AZ393CP-E1 Packing Type Tube Tape & Reel Tube Tape & Reel Tube Tube SOIC-8 Maximum Value 5mV 2mV 2mV DIP-8 Maximum Value 5mV 2mV BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant. Aug. 2006 Rev. 1. 2 3 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Absolute Maximum Ratings (Note 1) Parameter Supply Voltage Differential Input Voltage Input Voltage Input Current (VIN < -0.3V) (Note 2) Power Dissipation (TA=25oC) Output Short Circuit to Ground Operating Junction Temperature TJ TSTG TLEAD Symbol VCC VID VIN IIN Value 20 20 -0.3 to 20 50 DIP-8 780 660 150 Unit V V V mA mW PD SOIC-8 Continuous o C Storage Temperature Range Lead Temperature (Soldering, 10 seconds) -65 to 150 260 oC o C Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability. Note 2: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than -0.3 VDC (at 25oC). Recommended Operating Conditions Parameter Supply Voltage Operating Temperature Range Symbol VCC TA Min 2 -40 Max 18 85 Unit V oC Aug. 2006 Rev. 1. 2 4 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Electrical Characteristics VCC=5V, GND=0V, TA=25oC, unless otherwise specified. Parameter Input Offset Voltage Conditions AZ393 (Note 3) AZ393C Min Typ 1.0 1.0 25 5.0 Max 5.0 2.0 250 50 VCC - 1.5 Unit mV Input Bias Current Input Offset Current Input Common Mode Voltage Range Supply Current IIN+ or IIN- with output in linear range, VCM=0V, (Note 4) IIN+-IIN-, VCM=0V VCC=15V (Note 5) RL=∞, VCC=5V RL=∞, VCC=18V RL≥15KΩ, VCC=15V, VO=1V to 11V VIN=TTL logic swing, VREF=1.4V, VRL=5V, RL=5.1kΩ VRL=5V, RL=5.1kΩ, (Note 6) VIN-=1V, VIN+=0, VO ≤ 1.5V VIN-=1V, VIN+=0, ISINK ≤ 4mA VIN-=0, VIN+=1V, VO=5V 6.0 50 0 nA nA V 0.4 1.0 200 300 1.3 16 250 0.1 1.0 2.5 mA Voltage Gain Large Signal Response Time Response Time Output Sink Current Saturation Voltage Output Leakage Current V/mV ns µs mA 400 mV nA Note 3: At output switch point, VO=1.4V, RS=0 with VCC from 5V to 15V, and over the full common-mode range (0V to VCC-1.5V), at 25oC. Note 4: The direction of the input current is out of the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference of input lines. Note 5: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC-1.5V, but either or both inputs can go to +18V without damage, independent of the magnitude of VCC. Note 6: The response time specified is a 100mV input step with 5mV overdrive. For large overdrive signals 300ns can be obtained. Aug. 2006 Rev. 1. 2 5 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Typical Performance Characteristics 0.7 -40C 0.6 o 30 -40C 25 o Supply Current (mA) 25C 0.5 o 85C 0.4 o Input Current (nADC) 25C 20 o 85C 15 o 0.3 10 0.2 0.1 5 0.0 0 2 4 6 8 10 12 14 16 18 0 0 2 4 6 8 10 12 14 16 18 Supply Voltage (VDC) Supply Voltage (VDC) Figure 4. Supply Voltage vs. Supply Current Figure 5. Supply Voltage vs. Input Current 10 Output Voltage 6V 4V 2V 0 105mV VOUT VOUT 5V Saturation Voltage (VDC) 1 VIN VIN 5.1K VIN _ 5V Input Voltage 0.1 VOUT 100mV + 5.1K VIN _ VOUT 85C 0.01 o 25C o o 5mV 100mV + -40C 1E-3 0.01 0.1 1 10 100 Output Sink Current (mA) 0 0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4 Time (µs) Figure 6. Output Sink Current vs. Saturation Voltage 6V Figure 7. Response Time for 5mV Input Overdrive Negative Transition Output Voltage 4V 2V 0V 195mV 5V 5.1K VOUT VIN _ VOUT 100mV + Input Voltage VIN 95mV 0 0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4 Time (µs) Figure 8. Response Time for 5mV Input Overdrive Positive Transition Aug. 2006 Rev. 1. 2 6 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Typical Application VCC +5.0V 3K +VIN + 8 + 1/2 AZ393/C 100K 1/2 AZ393/C VO 1/4 MM54CXX 4 +VREF - Figure 9. Basic Comparator Figure 10. Driving CMOS/TTL VCC VCC 4.3K 1M 10K 100pF +VIN IN914 1M 1/2 AZ393/C 75pF - 100K VO 1/2 AZ393/C + VO + 0.001µF VIN 100K 1M IN914 100K Figure 11. One Shot Multivibrator Figure 12. Squarewave Oscillator Aug. 2006 Rev. 1. 2 7 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Mechanical Dimensions DIP-8 Unit: mm(inch) 0.700(0.028) 7.620(0.300)TYP 1.524(0.060) TYP 6° 6° 5° 3.710(0.146) 4.310(0.170) 4° 3.200(0.126) 3.600(0.142) 4° 3.000(0.118) 3.600(0.142) 0.510(0.020)MIN 0.254(0.010)TYP 0.360(0.014) 0.560(0.022) 2.540(0.100) TYP 0.130(0.005)MIN 0.204(0.008) 0.360(0.014) 8.200(0.323) 9.400(0.370) R0.750(0.030) Φ3.000(0.118) Depth 0.100(0.004) 0.200(0.008) 9.000(0.354) 9.400(0.370) 6.200(0.244) 6.600(0.260) Aug. 2006 Rev. 1. 2 8 BCD Semiconductor Manufacturing Limited Data Sheet LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS AZ393/393C Mechanical Dimensions (Continued) SOIC-8 Unit: mm(inch) 4.800(0.189) 5.000(0.197) 7° 1.350(0.053) 1.750(0.069) 0.320(0.013) 8° 7° 8° 0.675(0.027) 0.725(0.029) D 5.800(0.228) 6.200(0.244) D 20:1 1.270(0.050) TYP 0.100(0.004) 0.300(0.012) R0.150(0.006) φ 0.800(0.031) 0.200(0.008) 1.000(0.039) 3.800(0.150) 4.000(0.157) 0° 8° 0.330(0.013) 0.510(0.020) 0.900(0.035) 1° 5° R0.150(0.006) 0.190(0.007) 0.250(0.010) Aug. 2006 Rev. 1. 2 9 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or other rights nor the rights of others. MAIN SITE BCD Semiconductor Manufacturing Limited - Wafer Fab Shanghai SIM-BCD Semiconductor Manufacturing Limited 800, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 BCD Semiconductor Manufacturing Limited - IC Design Group Advanced Analog Circuits (Shanghai) Corporation 8F, Zone B, 900, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 REGIONAL SALES OFFICE Shenzhen Office Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. Shenzhen Office Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 27B, Tower C, 2070, Middle Shen Nan Road, Shenzhen 518031, China Tel: +86-755-8368 3987, Fax: +86-755-8368 3166 Taiwan Office BCD Semiconductor (Taiwan) Company Limited 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Taiwan Tel: +886-2-2656 2808, Fax: +886-2-2656 2806 USA Office BCD Semiconductor Corporation 3170 De La Cruz Blvd., Suite 105, Santa Clara, CA 95054-2411, U.S.A Tel: +1-408-988 6388, Fax: +1-408-988 6386