G53270004

PSE Technology Corporation SPECIFICATION FOR APPROVAL CUSTOMER 32.768 KHz NOMINAL FREQUENCY PRODUCT TYPE TYPE G5 SMD CRYSTAL SPEC. NO. ( P/N ) G53270004 CUSTOMER P/N 0 Mar.10,2014 , ISSUE DATE G VERSION APPROVED PREPARED QA AVL Status APPROVED BY CUSTOMER： Please return one copy with approval to PSE-TW PSE Technology Corporation No.2, Tzu-Chiang 5th Rd, Chung Li Industrial Park, Chung Li City, Taoyuan County, Taiwan (R.O.C.) TEL: 886-3-451-8888 FAX: 886-3-461-3865 http://www.saronix-ecera.com.tw E0-R-4-014 Rev. E *RoHS Exception *HF-Halogen Free *REACH Compliant Page i TYPE G5 SMD CRYSTAL G53270004 VER. G 10-Mar-14 VERSION HISTORY Version No. Version Date A Sep.28,2009 Initial Release B May.5,2010 Change Marking C Jul.1,2010 Change ESR from 60KΩ to 65KΩ D Sep.21,2010 New Logo & Changed Marking E Jan.19,2011 Updated Dimensions drawing F Jun.7,2011 Updated Dimensions drawing G Mar.10,2014 Updated Dimensions drawing E0-R-4-014 Rev. E Customer Receipt Date Supplier Receipt Date Description Notes Page ii TYPE G5 SMD CRYSTAL G53270004 VER. G 10-Mar-14 ELECTRICAL SPECIFICATIONS SRe Part Number : G53270004 Parameters Symbol Specifications Units Nominal Frequency Fn 32.768 KHz Frequency Tolerance FT ± 20 ppm Load Capacitance CL 12.5 pF Typ. Drive Level DL 1 μW Max. ESR 65 KΩ Max. K -0.035 TR -40~85 °C -55~85 °C Aging ±3 ppm Max 1st year Insulation Resistance 500 MΩ Min. Equivalent Series Resistance Temperature Coefficient Operating Temperature Range Storage Temperature Range Notes at 25°C ± 5°C ppm/°C Typ. Reliability ( Mechanical and Environmental Endurance ) No. 1 Test Items Vibration Test Method and Condition Requirements (1) Vibration Frequency: 10 to 55Hz Frequency Change: ±10ppm Max. (2) Vibration Amplitude: 1.5mm Resistance Change: ±15% or 5kΩ Max. (3) Cycle Time: 1-2min(10-55-10Hz) (4) Direction: X.Y.Z (5) Duration: 2h/each direction 2 3 Shock Leakage 3 Times free drop from 75cm height to hard wooden Frequency Change: ±10ppm Max. board of thickness more than 30mm Resistance Change: ±15% or 5kΩ Max. Put crystal units into a hermetic container and Leakage: 1x10¯8Pa·m3/s Max. Helium for 0.5-0.6Mpa, and keep it for 1h; Check the leakage by a Helium leak detector E0-R-4-014 Rev. E Page 1 TYPE G5 SMD CRYSTAL G53270004 4 Reflow soldering VER. G 10-Mar-14 Frequency Change: ±10ppm Max. Frequency Change: ±10ppm Max. Resistance Change: ±25% or 10kΩ Max. Note: the temperature used herein means the temperature on the circuit board. Reflow: 2 times max. 5 Lead Strength The crystal lead with the 0.9kg(9N) power (keep it for (DIP) 30s±5s) and bend the crystal lead 90° with 0.45kg The crystal lead is not abnormity power and two times 6 High Temperature The crystal units shall be put in somewhere for 2 hrs Frequency Change: ±10ppm Max. Endurance Resistance Change:±15% or 5kΩ Max. at temperature of -85℃±2℃, then keep it for 1 to 2 hrs under room temperature. 7 Low Temperature The crystal units shall be put in somewhere for 2 hrs Endurance at temperature of -25℃, then keep it for 1 to 2 hrs under room temperature. 8 Humidity The crystal units shall be put in somewhere at 40℃ Endurance in relative humidity of 90-95% for 48 hrs, then keep it for one or two hours under room temperature. 9 Temperature Temperature shift from low(-40℃) to high(100℃, keep Cycle 30 mins), satisfy high(100℃) to low(-40℃, keep 30 mins), then go up to room temperature for 5 cycles. 10 Salt Spray Test Put the crystal units in the salt spray room (salt The appearance shall has no abnormity density: 5%) at the temperature of 35℃ for 96 hrs. and soldering is good. Then clean it with water and dry its surface. Frequency Change: ±10ppm Max. Resistance Change:±15% or 5kΩ Max. E0-R-4-014 Rev. E Page 2 TYPE G5 SMD CRYSTAL G53270004 VER. G 10-Mar-14 Marking T32 Dimensions (Units: mm) Internal Lead Connection Note: Recommended Soldering Pattent(unit: mm) 1. Do not connect #2 and #3 to external device and GND. 2. The part of the cylinder inside resin mold may be sometimes exposed, however, it does not affect the characteristics of crystal unit. 3. Please make sure that there is no pattern under TMXLF-130 on the circuit board. E0-R-4-014 Rev. E Page 3 TYPE G5 SMD CRYSTAL G53270004 VER. G 10-Mar-14 TAPE AND REEL SPECIFICATION 1. Tape and Reel form conform to EIA-481-B. 2. The quantity of crystal units per reel shall be 3000PCS. 3. A "LABEL" on which necessary information is clearly written is on the surface of packing box and the reel. CARRIER TAPE DIMENSIONS REEL DIMENSIONS E0-R-4-014 Rev. E Page 4