G93270002

PSE Technology Corporation SPECIFICATION FOR APPROVAL CUSTOMER 32.768 KHz NOMINAL FREQUENCY PRODUCT TYPE TYPE G9 SMD CRYSTAL SPEC. NO. ( P/N ) G93270002 CUSTOMER P/N 0 Oct.31,2013 ISSUE DATE C VERSION APPROVED PREPARED QA AVL Status APPROVED BY CUSTOMER： Please return one copy with approval to PSE-TW PSE Technology Corporation No.2, Tzu-Chiang 5th Rd, Chung Li Industrial Park, Chung Li City, Taoyuan County, Taiwan (R.O.C.) TEL: 886-3-451-8888 FAX: 886-3-461-3865 http://www.saronix-ecera.com.tw E0-R-4-014 Rev. E *Pb-free *RoHS Compliant *HF-Halogen Free *REACH Compliant Page i TYPE G9 SMD CRYSTAL G93270002 VER. C 31-Oct-13 VERSION HISTORY Version No. Version Date A Apr.18,2011 Initial Release B Oct.3,2011 Changed Operating Temperature Range from -30~70°C to -40~85°C & Added Shunt Capacitance 7pF c Oct.31,2013 Revised to RoHS Compliant E0-R-4-014 Rev. E Customer Receipt Date Supplier Receipt Date Description Notes Page ii TYPE G9 SMD CRYSTAL G93270002 VER. C 31-Oct-13 ELECTRICAL SPECIFICATIONS SRe Part Number : G93270002 Parameters Symbol Specifications Units Nominal Frequency Fn 32.768 KHz Frequency Tolerance FT ± 20 ppm Load Capacitance CL 12.5 pF Drive Level DL 0.1 / 0.5 μW Typ / Max. ESR 90 KΩ Max. K -0.03 Operating Temperature Range TR -40~85 °C Shunt Capacitance C0 7 pF -55~125 °C Aging ±3 ppm Max 1st year Insulation Resistance 500 MΩ Min. Equivalent Series Resistance Temperature Coefficient Storage Temperature Range Notes at 25°C ± 5°C Typ. 2 ppm/°C Typ. Max. Reliability ( Mechanical and environmental performances ) No. Test Items 1 Bending test 2 Shear test 3 Core body strength 4 Vibration 5 Shock E0-R-4-014 Rev. E Conditions Requirements Apply pressure in the direction of the arrow at a rate of ․Without mechanical damage such as about 0.5mm/s until bent width reaches 5mm, and hold breaks and satisfy sealing specification. for 30 seconds. ․Frequency change: Within ±5ppm A static load of 20N(2.04kgf) using a R0.5 scratch tool, ․Equivalent series resistance(E.S.R) shall be applied on the core of the component and in change: Within 5kΩ the direction of the arrow and held for 5 seconds. A static load of 10N(1.02kgf) using a R0.5 pressure rod shall be applied to the center in the direction of the arrow and held for 10 seconds. Endurance conditioning by a frequency sweep shall be made. The entire frequency range, from 10Hz to 55Hz and return to 10Hz, shall be transversed in 1 minute. Amplitude (total excursion) ：1.5mm, This motion shall be applied for a period of 2 hours in each of 3 mutually perpendicular axes (a total of 6 hours). For other procedures, refer to JIS C 60068-2-6. Peak acceleration：9810m/s2，Duration of the pulse： 1ms, Three successive shock shall be applied 3 times perpendicular axes. For other procedures, refer to JIS C 60068-2-27. Page 1 TYPE G9 SMD CRYSTAL G93270002 VER. C 31-Oct-13 6 Cold ․Frequency change: Within ±5ppm Quartz crystal units shall be stored in the -40±3℃ atmosphere for 1000 hours. Other procedures conform ․Equivalent series resistance(E.S.R) to JIS C 60068-2-1. change: Within 5kΩ 7 Dry heat Quartz crystal units shall be stored in the 100±2℃ ․After conditioning, quartz crystal units atmosphere for 100 hours. Other procedures conform to shall be subjected to standard atmospheric JIS C 60068-2-2. conditions for 1 hour, and measured. 8 Damp heat Quartz crystal units shall be stored in the 40±2℃ atmosphere with 90 to 95% relative humidity for 1000 hours. Other procedures conform to JIS C 60068-2-3. 9 Change of temperature Quartz crystal units shall be subjected successively 100 cycles of temperature change shown below. Other procedures conform to JIS C 0025. Temperature 1 2 3 4 10 Sealing -40±3℃ Normal temperature 100±2℃ Normal temperature Duration 30min. Within 30 sec. 30min. Within 30 sec. Both the test methods specified below shall be applied. Quartz crystal units shall be soaked in 90℃ or higher temperature hot water for 5 minutes. ․Without repetitive leaking bubbles from quartz crystal units. ․1×10-9 Pa･m3/s or less Quartz crystal units shall be tested by Mass spectrometric leakage detector to measure the leakage rate of helium gas. 11 Aging Quartz crystal units shall be stored in the 85±3℃ atmosphere for 720±12 hours. ․Frequency change: Within ±5ppm ․Equivalent series resistance(E.S.R) change: Within 5kΩ ․After conditioning, quartz crystal units shall be subjected to standard atmospheric conditions for 1 hour, and measured. 12 Solder-ability Terminals coated with flux shall be immersed in the solder bath for 3.5±0.5 seconds. Items 1 Solder 2 Flux 3 E0-R-4-014 Rev. E Solder temperature ․Minimum 95% of immersed terminal shall be covered with new uniform solder. Conditions Sn-3.0Ag-0.5Cu Approximately 25wt% methanol(JIS K 8891) solution of resin(JIS K 5902). 255±5℃ Page 2 TYPE G9 SMD CRYSTAL G93270002 13 Resistance to soldering heat VER. C 31-Oct-13 Reflow soldering method Peak temperature: 260±5℃ for within 5seconds. Soldering temperature: 220℃ or higher for 60±10 seconds. Pre-heating temperature: 160±10℃ for 90±10 seconds. Quartz crystal units which is put on PCB shall be through reflow soldering furnace twice with the condition shown above. Soldering iron method ․Frequency change: Within ±5ppm ․Equivalent series resistance (E.S.R) change: Within 10kΩ ․After conditioning, quartz crystal units shall be subjected to standard atmospheric conditions for 1 hour, and measured. ․Without distinct deformation in appearance. ․Frequency change: Within ±5ppm Terminals shall be applied 400±10℃ soldering iron heat ․Equivalent series resistance(E.S.R) for 3.5±0.5 seconds twice. change: Within 5kΩ ․After conditioning, quartz crystal units shall be subjected to standard atmospheric conditions for 1 hour, and measured. ․Without distinct deformation in appearance. 14 Solubility to resistance E0-R-4-014 Rev. E Soak cleaning Quartz crystal units shall be soaked in isopropyl alcohol at normal temperature for 90 seconds. ․Without mechanical damage such as breaks and satisfy sealing specification. ․Frequency change: Within ±5ppm ․Equivalent series resistance(E.S.R) change: Within 5kΩ ․Without distinct deformation in appearance. ․Marking shall be legible. Page 3 TYPE G9 SMD CRYSTAL G93270002 VER. C 31-Oct-13 Marking BEmv m v Date Code Factory Code Dimensions (Units: mm) Land dimensions(unit: mm) E0-R-4-014 Rev. E Page 4 TYPE G9 SMD CRYSTAL G93270002 VER. C 31-Oct-13 TAPING REEL E0-R-4-014 Rev. E Page 5