PAM8006ATR

A Product Line of Diodes Incorporated PAM8006A 15W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH POWER LIMIT Description Pin Assignments The PAM8006A is a 15W (per channel) stereo Class-D audio amplifier which offers low THD+N (0.2%), low EMI and good PSRR thus high quality sound reproduction. The PAM8006A runs off of an 8V to 18V supply at much higher efficiency than competitors’ Ics. The PAM8006A only requires very few external components, significantly saving cost and board space. The PAM8006A is available in a QFN5x5-32L package. Features  15W x2 into a 8Ω speaker  Low Noise: -90dB  Over 90% Efficiency  With Shutdown/Mute Function  Over Current ,OVP,UVLO,Thermal and Short-Circuit Protection  Low THD+N Applications  Power Limit with Non-Clip   Flat Monitor /LCD TVs Low Quiescent Current   Multi-Media Speaker System Pop Noise Suppression   DVD Players, Game Machines Small Package Outlines: QFN5x5-32L   Boom Box Pb-Free Package (RoHS Compliant)  Music Instruments Typical Applications Circuit PAM8006A Document number: DSxxxxx Rev. 1 - 0 1 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Pin Descriptions Pin Number 1, 8, 17, 24 2 3 4 5 6 7 9, 16 10, 15 11 12 13 14 18 19 20 21 22 Package Name NC RINN RINP MUTE AVDD LINP LINN PGNDL PVCCL LOUTN BSLN BSLP LOUTP PL V2P5 AGND VCLAMP AVCC 23 SD 25, 32 26, 31 27 28 29 30 PGNDR PVCCR ROUTP BSRP BSRN ROUTN 33 Thermal Pad PAM8006A Document number: DSxxxxx Rev. 1 - 0 Function Not Connected Negative differential audio input for right channel. Positive differential audio input for right channel. A logic high on this pin disables the outputs and a logic low enables the outputs. 5V Analog Supply Positive differential audio input for left channel. Negative differential audio input for left channel. Power ground for left channel H-bridge. Power supply for left channel H-bridge, not connected to PVCCR or AVCC. Class-D 1/2-H-bridge negative output for left channel. Bootstrap I/O for left channel, negative high-side FET. Bootstrap I/O for left channel, positive high-side FET. Class-D 1/2-H-bridge positive output for left channel. Reference voltage for power limit function. 2.5V Reference for analog cells. Analog Ground Internally generated voltage supply for bootstrap capacitors. High-voltage analog power supply (8V to 26V) Shutdown signal for IC (low= shutdown, high = operational). TTL logic levels with compliance to VCC. Power ground for right channel H-bridge. Power supply for right channel H-bridge, not connected to PVCCL or AVCC. Class-D 1/2-H-bridge positive output for right channel. Bootstrap I/O for right channel, positive high-side FET. Bootstrap I/O for right channel, negative high-side FET. Class-D 1/2-H-bridge negative output for right channel. Connect to ground. Thermal pad should be soldered down on all applications to secure the device properly to the printed wiring board. 2 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Functional Block Diagram Notes: Maximum Gain: RI = 12.5k, RF = 100k; Power Limit Function: RI and RF are adjustable. Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.) These are stress ratings only and functional operation is not implied. Exposure to absolute maximum ratings for prolonged time periods may affect device reliability. All voltages are with respect to ground. Parameter Rating Unit -0.3 to +28.0 V Input Voltage Range VI: MUTE, PL 0 to 6.0 V SD RINN, RINP, LINN, LINP -0.3 to VCC V -0.3 to +6.0 V -40 to +125 °C -65 to +150 °C 260 (5sec) °C Supply Voltage VCC Junction Temperature Range, TJ Storage Temperature Lead Temperature 1, 6mm (1/16inch) PAM8006A Document number: DSxxxxx Rev. 1 - 0 3 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.) Parameter Rating Supply Voltage VCC Input Pin Voltage High Level Input Voltage: SD MUTE Low Level Input Voltage: SD MUTE Ambient Operating Temperature Unit 8 to 18 V 0 to 5.5 V 2.0 to VCC 2.0 to 5.5 0 to 0.3 0 to 0.3 -20 to +85 V V V V °C Thermal Information Parameter Thermal Resisitance (Junction to Case) Thermal Resistance (Junction to Ambient) Package Symbol Maximum QFN5x5-32L θJC 5.0 QFN5x5-32L θJA 16.1 Unit °C/W The exposed PAD must be soldered to a thermal land on the PCB. Electrical Characteristics (@TA = +25°C, VCC = 12V, RL =8Ω, unless otherwise specified.) Symbol Parameter Conditions THD+N = 0.12%, f = 1kHz, RL = 8Ω PO Continuous Output Power 8.5 10 (No Load) ISD Supply Quiescent Current in Shutdown Mode Shutdown = 0V Drain-Source On-State Resisitance IO = 0.5A TJ = +25°C Power Supply Ripple Rejection Ratio High Side Low Side Total Max Units 6 THD+N = 10%, f = 1kHz, RL = 8Ω Quiescent Current PSRR Typ THD+N = 1%, f = 1kHz, RL = 8Ω IDD RDS(ON) Min W 16.5 25 mA 4 10 µA 210 210 420 mΩ 1VPP Ripple, f = 1kHz, Inputs AC-Coupled to Ground -65 dB fOSC Vn 300 kHz Output Integrated Noise Floor Oscillator frequency 20Hz to 22kHz, A-Weighting -100 dB CS Crosstalk PO = 3W, RL = 8Ω, f = 1kHz Maximum Output at THD+N < 0.5%, f = 1kHz -95 dB 90 dB 32 dB SNR Signal to Noise Ratio |VOS| INN and INP Connected Together 30 mV V2P5 Gain Output Offset Voltage (measured differentially) 2.5V Bias Voltage No Load 2.5 V AVDD Internal Analog Supply Voltage VCC = 8V to 26V OTS OTH Over Temperature Shutdown Thermal Hysteresis PAM8006A Document number: DSxxxxx Rev. 1 - 0 5 160 50 4 of 13 www.diodes.com 5.5 V °C °C April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Electrical Characteristics (@TA = +25°C, VCC = 18V, RL =8Ω, unless otherwise specified.) Symbol PO THD+N Parameter Continuous Output Power Conditions THD+N = 0.18%, f = 1kHz, RL = 8Ω 15 Total Harmonic Distortion plus Noise PO = 10W, f = 1kHz, RL = 8Ω IDD (No Load) ISD Supply Quiescent Current in Shutdown Mode Shutdown = 0V Drain-Source On-State Resisitance IO = 0.5A TJ = +25°C Power Supply Ripple Rejection Ratio 1VPP Ripple, f = 1kHz, Inputs AC-Coupled to Ground PSRR Typ 2.2 Quiescent Current RDS(ON) Min THD+N = 0.12%, f = 1kHz, RL = 8Ω Oscillator Frequency Units W 0.28 18 High Side Low Side Total Max % 25 mA 50 µA 210 210 420 mΩ -65 dB 300 kHz fOSC Vn Output Integrated Noise Floor 20Hz to 22kHz, A-Weighting -100 dB CS Crosstalk PO = 3W, RL = 8Ω, f = 1kHz Maximum Output at THD+N < 0.5%, f = 1kHz -95 dB 90 dB 32 dB mV SNR Signal to Noise Ratio |VOS| INN and INP Connected Together 30 V2P5 Gain Output Offset Voltage (measured differentially) 2.5V Bias Voltage No Load 2.5 AVDD Internal Analog Supply Voltage VCC = 8V to 26V OTS OTH Over Temperature Shutdown Thermal Hysteresis PAM8006A Document number: DSxxxxx Rev. 1 - 0 5 160 50 5 of 13 www.diodes.com V 5.5 V °C °C April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Typical Performance Characteristics (VCC = 18, RL = 8Ω, GV = 32dB, TA = +25°C, VCC = 12V, RL =8Ω, unless otherwise specified.) PAM8006A Document number: DSxxxxx Rev. 1 - 0 6 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Typical Performance Characteristics (cont.) (VCC = 18, RL = 8Ω, GV = 32dB, TA = +25°C, VCC = 12V, RL =8Ω, unless otherwise specified.) PAM8006A Document number: DSxxxxx Rev. 1 - 0 7 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Application Information Test Setup for Performance Testing Notes: 1. The AP AUX-0025 low pass filter is necessary for class-D amplifier measurement with AP analyzer. 2. Two 22μH inductors are used in series with load resistor to emulate the small speaker for efficiency measurement. MUTE Operation The MUTE pin is an input for controlling the output state of the PAM8006A. A logic high on this pin disables the outputs and low enables the outputs. This pin may be used as a quick disable or enable of the outputs without a volume fade. Shutdown Operation The PAM8006A employs a shutdown operation mode to reduce supply current to the absolute minimum level during periods of non-use to save power. The SD input terminal should be held high during normal operation when the amplifier is in use. Pulling SD low causes the outputs to mute and the amplifier to enter a low-current state. SD should never be left unconnected to prevent the amplifier from unpredictable operation. For the best power-off pop performance, the amplifier should be set in shutdown mode prior to removing the power supply voltage. Internal 2.5V Bias Generator Capacitor Selection The internal 2.5V bias generator (V2P5) provides the internal bias for the preamplifier stage. The external input capacitors and this internal reference allow the inputs to be biased within the optimal common-mode range of the input preamplifiers. The selection of the capacitor value on the V2P5 terminal is critical for achieving the best device performance. During startup or recovery from shutdown state, the V2P5 capacitor determines the rate at which the amplifier starts up. When the voltage on the V2P5 capacitor equals 0.75 x V2P5, or 75% of its final value, the device turns on and the Class-D outputs start switching. The startup time is not critical for the best de-pop performance since any heard pop sound is the result of the Class-D output switching-on other than that of the startup time. However, at least a 0.47μF capacitor is recommended for the V2P5 capacitor. Another function of the V2P5 capacitor is to filter high frequency noise on the internal 2.5V bias generator. Power Supply Decoupling, CS The PAM8006A is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) as low as possible. Power supply decoupling also prevents oscillations caused by long lead between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series resistance (ESR) ceramic capacitor, typically 1μF, is recommended, placing as close as possible to the device’s VCC lead. To filter lower frequency noises, a large aluminum electrolytic capacitor of 10μF or greater is recommended, placing near the audio power amplifier. The 10μF capacitor also serves as a local storage capacitor for supplying current during large signal transients on the amplifier outputs. BSN and BSP Capacitors The full H-bridge output stages use NMOS transistors only. They therefore require bootstrap capacitors for the high side of each output to turn on correctly. An at least 220nF ceramic capacitor, rated for at least 25V, must be connected from each output to its corresponding bootstrap input. Specifically, one 220nF capacitor must be connected from xOUTP to xBSP, and another 220nF capacitor from xOUTN to xBSN. It is recommended to use 1μF BST capacitor to replace 220nF or lower than 100Hz applications. PAM8006A Document number: DSxxxxx Rev. 1 - 0 8 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Application Information (cont.) VCLAMP Capacitors To ensure that the maximum gate-to-source voltage for the NMOS output transistors not exceeded, an internal regulators are used to clamp the gate voltage. A 1μF capacitors must be connected from VCLAMP to ground and must be rated for at least 25V. The voltages at the VCLAMP terminals vary with VCC and may not be used to power any other circuitry. Internal Regulated 5-V Supply (AVDD) The AVDD terminal is the output of an internally generated 5V supply, used for the oscillator, amplifier, power limit circuitry and logic control circuitry. It requires a 0.1μF to 1μF capacitor, placed very close to the pin to ground to keep the regulator stable. The regulator may not be used to power any external circuitry. Differential Input Power Limit The differential input stage of the amplifier eliminates noises that appear on the two input lines of the channel. To use the PAM8006A with a differential source, connect the positive lead of the audio source to the INP input and the negative lead from the audio source to the INN input. To use the PAM8006A with a single-ended source, AC ground the INP input through a capacitor equal in value to the input capacitor on INN and apply the audio source to the INN input. In a single-ended input application, the INP input should be AC grounded at the audio source other than at the device input for best noise performance. Using Low-ESR Capacitors Low-ESR capacitors are recommended throughout this application section. A real (with respect to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance the more the real capacitor behaves as an ideal capacitor. Short-Circuit Protection The PAM8006A has short circuit protection circuitry on the outputs to prevent damage to the device when output-to-output shorts, output-to-GND shorts, or output-to-VCC shorts occur. Once a short-circuit is detected on the outputs, the output drive is immediately disabled. This is a latched fault and must be reset by cycling the voltage on the SD pin to a logic low and back to the logic high state for normal operation. This will clear the short-circuit flag and allow for normal operation if the short was removed. If the short was not removed, the protection circuitry will again activate. Thermal Protection Thermal protection on the PAM8006A prevents damage to the device when the internal die temperature exceeds 160°C. There is a ±15 degree tolerance on this trip point from device to device. Once the die temperature exceeds the set thermal point, the device enters into the shutdown state and the outputs are disabled. This is not a latched fault. The thermal fault is cleared once the temperature of the die is reduced by 50°C. The device begins normal operation at this point without external system intervention. Power Limit The voltage at PL pin can used to limit the power to levels below that which is possible based on the supply rail. Add a resistor from PL to ground to set the voltage at the PLIMIT pin. An external reference may also be used if tighter tolerance is required. Also add a 1µF capacitor from PL pin to ground. The PLIMIT circuit sets a limit on the output peak-to-peak voltage. The gain of Class-D amplifier will automatic reduced if the output power higher than setting value to make output power less than limited value and also provide good sound quality. PAM8006A Document number: DSxxxxx Rev. 1 - 0 9 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Application Information (cont.) Power Limit (cont.) The output power vs PL pin resistor value as below. VCC = 12V, RLOAD = 8Ω R(Ω) PL(V) PL(W) R(Ω) PL(V) PL(W) 56K 0.61 3.1 100K 0.99 8.1 62K 0.67 3.7 110K 1.07 9.0 68K 0.73 4.3 120K 1.15 9.6 75K 0.79 5.1 130K 1.22 10.0 82K 0.85 6.0 140K 1.36 10.7 91K 0.92 7.0 — — — Power Up/Down Sequence The PAM8006A employs a shutdown operation mode to reduce supply current to the absolute minimum level during periods of non-use to save power. The SD input terminal should be held high during normal operation when the amplifier is in use. Pulling SD low causes the outputs to mute and the amplifier to enter a low-current state. SD should never be left unconnected to prevent the amplifier from unpredictable operation. Suggest PL starting voltage is greater than 5V. Start-up /power down sequencer recommended. PAM8006A Document number: DSxxxxx Rev. 1 - 0 10 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Ordering Information Part Number PAM8006ATR Part Marking PAM8006A XXXYWWLL Package Type Standard Package QFN5x5-32L 3000 Units/Tape&Reel Marking Information PAM8006A Document number: DSxxxxx Rev. 1 - 0 11 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A Package Outline Dimensions (All dimensions in mm.) QFN5x5-32L PAM8006A Document number: DSxxxxx Rev. 1 - 0 12 of 13 www.diodes.com April 2013 © Diodes Incorporated A Product Line of Diodes Incorporated PAM8006A IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2013, Diodes Incorporated www.diodes.com PAM8006A Document number: DSxxxxx Rev. 1 - 0 13 of 13 www.diodes.com April 2013 © Diodes Incorporated