PI3C3125QEX

A product Line of Diodes Incorporated PI3C3125/PI3C3126 2.5V/3.3V, High Bandwidth, Hot Insertion,4-Bit, 2-Port Bus Switch with Individual Enables Features Description ÎÎ Near-Zero propagation delay ÎÎ 5-ohm switches connect inputs to outputs ÎÎ High Bandwidth (>400 MHz) ÎÎ Rail-to-Rail, or 2.5V or 3.3V Switching ÎÎ 5V I/O Tolerant ÎÎ 2.5V Supply Voltage Operation ÎÎ Permits Hot Insertion ÎÎ Packaging (Pb-free & Green available): Diodes’ PI3C3125 and PI3C3126 are 2.5 volt or 3.3 volt, 4-bit bus switches designed with four individual 5-ohm bus switches with fast indiviual enables in an industry standard 74XX125/126 pinout. When enabled via the associated Bus Enable pin, the “A” pin is directly connected to the “B” pin for that particular gate. The bus switch introduces no additional propagation delay or additional ground bounce noise. The PI3C3125 device has active LOW enables, and the PI3C3126 has active HIGH enables. It is very useful in switching signals that have high bandwidth (>400 MHz). – 14-pin 150-mil wide plastic SOIC (W) – 14-pin 170-mil wide plastic TSSOP (L) – 16-pin 150-mil wide plastic QSOP (Q) Applications ÎÎ High Bandwidth Data Switching ÎÎ Hot Docking PI3C3126 Block Diagram PI3C3125 Block Diagram A0 A0 B0 BE0 BE0 A1 A1 B1 A2 B2 A3 B3 Document Number DS40194 Rev 1-2 B3 BE3 BE3 PI3C3125/PI3C3126 B2 BE2 BE2 A3 B1 BE1 BE1 A2 B0 1 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature............................................................. –65°C to +150°C Ambient Temperature with Power Applied............................ –40°C to +85°C Supply Voltage to Ground Potential (Inputs & VCC Only)...... –0.5V to +4.6V Supply Voltage to Ground Potential (Outputs & D/O Only)...–0.5V to +4.6V DC Input Voltage.....................................................................–0.5V to +5.5V DC Output Current................................................................................ 120mA Junction Temperature..............................................................................125°C PI3C3125 14-Pin Configuration BE0 A0 B0 BE1 A1 B1 GND 1 14 2 13 3 14-PIN 12 4 W14 11 5 L14 10 6 9 7 8 1 16 2 15 3 16-PIN 14 4 Q16 13 5 12 6 11 7 10 8 9 Vcc BE3 A3 B3 BE2 A2 B2 BE0 A0 B0 BE1 A1 B1 GND PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 Power Ground 1 14 2 13 3 14-PIN 12 4 W14 11 5 L14 10 6 9 7 8 Vcc BE3 A3 B3 BE2 A2 B2 PI3C3126 16-Pin Configuration NC BE0 A0 B0 BE1 A1 B1 GND Vcc BE3 A3 B3 BE2 A2 B2 NC Pin Description Pin Name Description BEn Switch Enable (PI3C3125) BEn Switch Enable (PI3C3126) A3 - A0 Bus A B3 - B0 Bus B VCC GND Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. PI3C3126 14-Pin Configuration PI3C3125 16-Pin Configuration NC BE0 A0 B0 BE1 A1 B1 GND Note: Truth Table(1) PI3C3125 PI3C3126 BEn BEn X* H L X L H 1 16 2 15 3 16-PIN 14 4 Q16 13 5 12 6 11 7 10 8 9 Vcc BE3 A3 B3 BE2 A2 B2 NC An Bn VCC Function Hi-Z Hi-Z Bn Hi-Z Hi-Z An GND VCC VCC Disconnect Disconnect Disconnect Note: 1. H = High Voltage Level, L = Low Voltage Level HI-Z = High Impedance, X = Don’t Care * A pull-up resistor should be provided for power-up protection. 2 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 DC Electrical Characteristics (Over Operating Range, TA = –40°C to +85°C, VCC = 3.3V ±10%) Parameters Description Test Conditions(1) VIH VIL IIH IIL IOZH(3) Input HIGH Voltage Input LOW Voltage Input HIGH current Input LOW Current High Impedance Output Current Clamp Diode Voltage Switch ON Resistance(4) Guearanteed Logic HIGH Level Guaranteed Logic LOW Level –0.5 VCC = Max., VIN = VCC VCC = Max., VIN = GND 0 ≤ A, B ≤ VCC VIK RON Min. Typ.(2) Max Units 2.0 V 0.8 VCC = Min., IIN = –18mA VCC = Min., VIN = 0.0V, ION = 48mA or 60mA VCC = Min., VIN = 2.4V, ION = 15mA –0.73 5 8 ±1 ±1 ±1 µA µA –1.2 7 15 V Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. Capacitance (TA = 25°C, f = 1 MHz) Parameters(1) CIN COFF CON Description Input Capacitance A/B Capacitance, Switch Off A/B Capacitance, Switch On Test Conditions VIN = 0V VIN = 0V VIN = 0V Typ. Units 3.5 5.0 10.0 pF Notes: 1. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters ICC ∆ICC Description Quiescent Power Supply Current Supply Current per Input HIGH Test Conditions VCC = Max VIN = GND or VCC VCC = Max 3.0V(3) VIN = Min. Typ.(2) Max. 260 500 Units µA 750 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25°C ambient. 3. Per driven input (control input only); A and B pins do not contribute to ΔICC. PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 3 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 PI3C3125/PI3C3126 Switching Characteristics over 3.3V Operating Range Parameters Description Conditions tPLH tPHL Propogation Delay(1,2) A to B, B to A CL =50pF RL = 500Ω tPZH tPZL tPHZ tPLZ Bus Enable Time CL =50pF RL = 500Ω R = 500Ω Bus Disable Time PI3C3125/PI3C3126 Com. Min. Max. 0.25 1.5 6.5 1.5 5.5 Units ns Notes: 1. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. PI3C3125/PI3C3126 Switching Characteristics over 2.5V Operating Range Parameters Description Conditions tPLH tPHL Propogation Delay(1,2) A to B, B to A CL =50pF RL = 500Ω tPZH tPZL tPHZ tPLZ Bus Enable Time CL =50pF RL = 500Ω R = 500Ω Bus Disable Time PI3C3125/PI3C3126 Com. Min. Max. 0.25 1.5 9.8 1.5 8.3 Units ns Notes: 1. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4.0 VCC V 3.1V 2.9V 2.7V 2.5V 3.4V 3.2V 3.0V 2.8V 2.0 VOUT ) 2.3V 3.8V 3.6V 0.0 0.0 1.0 3.0 2.0 4.0 5.0 VIN (V) Switch Output Voltage vs. Input Voltage over Various Supply Voltages PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 4 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 Packaging Mechanical: 14-SOIC (W) 16-0055 PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 5 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 Packaging Mechanical: 14-TSSOP (L) 16-0060 PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 6 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 Packaging Mechanical: 16-QSOP (Q) 16-0056 For latest package info. please check: http://www.diodes.com/design/support/packaging/pericom-packaging/packaging-mechanicals-and-thermal-characteristics/ Ordering Information Ordering Code Packaging Code PI3C3125LEX PI3C3125WEX PI3C3126LEX PI3C3126QEX L W L Q Description 14-pin, 173mil Wide (TSSOP) 14-pin, 150mil Wide (SOIC) 14-pin, 173mil Wide (TSSOP) 16-pin, 150mil Wide (QSOP) Notes: • Thermal characteristics can be found on the company web site at www.diodes.com/design/support/packaging/ • E = Pb-free and Green • X suffix = Tape/Reel PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 7 www.diodes.com September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3C3125/PI3C3126 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com PI3C3125/PI3C3126 Document Number DS40194 Rev 1-2 8 www.diodes.com September 2017 Diodes Incorporated