PI3C3126WEX

A product Line of Diodes Incorporated PI3C3126 2.5V/3.3V, High Bandwidth, Hot Insertion,4-Bit, 2-Port Bus Switch with Individual Enables Features Description • Near-Zero propagation delay Pericom Semiconductor’s PI3C3126 is a 2.5 volt or 3.3 volt, 4-bit bus switch designed with four individual 5-ohm bus switches with fast indiviual enables in an industry standard 74XX125/126 pinout. When enabled via the associated Bus Enable pin, the “A” pin is directly connected to the “B” pin for that particular gate. The bus switch introduces no additional propagation delay or additional ground bounce noise. • 5-ohm switches connect inputs to outputs • High Bandwidth (>400 MHz) • 2.5V/3.3V Supply Voltage Operation • Rail-to-Rail, or 2.5V or 3.3V Switching • 5V I/O Tolerant The PI3C3126 has active HIGH enables. It is very useful in switching signals that have high bandwidth (>400 MHz). • Permits Hot Insertion • Packaging (Pb-free & Green available): – 14-pin 170-mil wide plastic TSSOP (L) 14-Pin Configuration – 16-pin 150-mil wide plastic QSOP (Q) Applications BE0 A0 B0 BE1 A1 B1 GND • High Bandwidth Data Switching • Hot Docking Block Diagram B0 A0 BE0 NC BE0 A0 B0 BE1 A1 B1 GND BE1 B2 A2 BE2 B3 A3 BE3 1 16 2 15 3 16-PIN 14 4 Q16 13 5 12 6 11 7 10 8 9 Vcc BE3 A3 B3 BE2 A2 B2 NC Truth Table(1) Pin Description VCC GND Vcc BE3 A3 B3 BE2 A2 B2 16-Pin Configuration B1 A1 Pin Name BEn A3 - A0 B3 - B0 1 14 2 13 3 14-PIN 12 4 L14 11 5 10 6 9 7 8 Description Switch Enable Bus A Bus B BEn X L H Power Ground All trademarks are property of their respective owners. An Hi-Z Hi-Z Bn Bn Hi-Z Hi-Z An VCC GND VCC VCC Note: 1. H = High Voltage Level, L = Low Voltage Level HI-Z = High Impedance, X = Don’t Care 16-0014 1 Function Disconnect Disconnect Connect www.diodes.com 06/30/16 A product Line of Diodes Incorporated PI3C3126 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature............................................................. –65°C to +150°C Ambient Temperature with Power Applied............................ –40°C to +85°C Supply Voltage to Ground Potential (Inputs & VCC Only)......–0.5V to +4.6V Supply Voltage to Ground Potential (Outputs & D/O Only)...–0.5V to +4.6V DC Input Voltage.....................................................................–0.5V to +5.5V DC Output Current................................................................................ 120mA Power Dissipation.................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over Operating Range, TA = –40°C to +85°C, VCC = 3.3V ±10%) Parameters VIH VIL IIH IIL VIK Description Input HIGH Voltage Input LOW Voltage Input HIGH current Input LOW Current High Impedance Output Current Clamp Diode Voltage RON Switch ON Resistance(4) (3) IOZH Test Conditions(1) Guearanteed Logic HIGH Level Guaranteed Logic LOW Level –0.5 VCC = Max., VIN = VCC VCC = Max., VIN = GND Min. 2.0 Typ.(2) Max Units V 0.8 ±1 ±1 0 ≤ A, B ≤ VCC µA ±1 VCC = Min., IIN = –18mA VCC = Min., VIN = 0.0V, ION = 48mA or 60mA VCC = Min., VIN = 2.4V, ION = 15mA –0.73 –1.2 V 5 8 7 15 Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. Capacitance (TA = 25°C, f = 1 MHz) Parameters(1) CIN COFF CON Description Input Capacitance A/B Capacitance, Switch Off A/B Capacitance, Switch On Test Conditions VIN = 0V VIN = 0V VIN = 0V Typ. 3.5 5.0 10.0 Units pF Notes: 1. This parameter is determined by device characterization but is not production tested. All trademarks are property of their respective owners. 16-0014 2 www.diodes.com 06/30/16 A product Line of Diodes Incorporated PI3C3126 Power Supply Characteristics Parameters ICC ∆ICC Description Quiescent Power Supply Current Supply Current per Input HIGH Test Conditions Min. VCC = Max VIN = GND or VCC VCC = Max VIN = 3.0V(3) Typ.(2) Max. 260 500 Units µA 750 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25°C ambient. 3. Per driven input (control input only); A and B pins do not contribute to ΔICC. Switching Characteristics over 3.3V Operating Range Com. Parameters Description Conditions tPLH tPHL Propogation Delay(1,2) A to B, B to A CL =50pF RL = 500Ω Bus Enable Time CL =50pF RL = 500Ω R = 500Ω tPZH tPZL tPHZ tPLZ Bus Disable Time Min. Max. Units 0.25 1.5 6.5 1.5 5.5 ns Notes: 1. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Switching Characteristics over 2.5V Operating Range Com. Parameters Description Conditions tPLH tPHL Propogation Delay(1,2) A to B, B to A CL =50pF RL = 500Ω Bus Enable Time CL =50pF RL = 500Ω R = 500Ω tPZH tPZL tPHZ tPLZ Bus Disable Time Min. Max. Units 0.25 1.5 9.8 1.5 8.3 ns Notes: 1. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. All trademarks are property of their respective owners. 16-0014 3 www.diodes.com 06/30/16 A product Line of Diodes Incorporated PI3C3126 4.0 VCC V 3.1V 2.9V 2.7V 2.5V 3.4V 3.2V 3.0V 2.8V 2.0 VOUT ) 2.3V 3.8V 3.6V 0.0 0.0 1.0 3.0 2.0 4.0 5.0 VIN (V) Switch Output Voltage vs. Input Voltage over Various Supply Voltages All trademarks are property of their respective owners. 16-0014 4 www.diodes.com 06/30/16 A product Line of Diodes Incorporated PI3C3126 Packaging Mechanical: 14-Pin TSSOP (L14) 16-0060 All trademarks are property of their respective owners. 16-0014 5 www.diodes.com 06/30/16 A product Line of Diodes Incorporated PI3C3126 Packaging Mechanical: 16-Pin QSOP (Q16) 16-0056 Note: For latest package info, please check: http://www.pericom.com/support/packaging/packaging-mechanicals-and-thermal-characteristics/ Ordering Information Ordering Code Packaging Code PI3C3126LE PI3C3126LEX PI3C3126QE PI3C3126QEX L L Q Q Package Type 14-pin, 173mil Wide (TSSOP) 14-pin, 173mil Wide (TSSOP), Tape & Reel 16-pin, 150mil Wide (QSOP) 16-pin, 150mil Wide (QSOP), Tape & Reel Notes: • Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ • E = Pb-free & Green • Adding an X suffix = Tape/Reel All trademarks are property of their respective owners. 16-0014 6 www.diodes.com 06/30/16