PI3C3384QE

PI3C3384 2.5V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch Description Features Pericom Semiconductor’s PI3C3384 is a 2.5V or 3.3V, high bandwidth 10-bit, 2-port bus switches designed with a low OnResistance allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable (BE) input signal. Two bus enable signals are provided, one for each of the upper and lower five bits of the two 10-bit buses. • Near-Zero propagation delay • 5-ohm switches connect inputs to outputs • High Bandwidth (>400 MHz) • Permits Hot Insertion. • Rail-to-Rail, 3.3V or 2.5V Switching • 5V I/O Tolerant • 2.5V Supply Voltage Operation • Packaging (Pb-free & Green): – 24-pin 150-mil wide plastic QSOP (Q) Applications • High Bandwidth Data switching • Hot Docking Block Diagram Pin Configuration A0 B0 A4 B4 A5 B5 A9 B9 BEA B0 A0 A1 B1 B2 A2 A3 B3 B4 A4 GND BEA BEB Truth Table(1) Function BEA Disconnect H Connect L Connect H Connect L BEB H H L L B0-B4 Hi-Z A0-A4 Hi-Z A0-A4 Pin Description Pin Name BEA, BEB A0 - A9 B0 - B9 GND VCC B5-B9 Hi-Z Hi-Z A5-A9 A5-A9 Note: 1. High Voltage Level, X = Don't Care, L =- Low Voltage Level, Hi-Z = High Impedance 11-0008 1 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC B9 A9 A8 B8 B7 A7 A6 B6 B5 A5 BEB Description Bus Enable Inputs (Active LOW) Bus A Bus B Ground Power PS8757G 11/25/10 PI3C3384 2.5V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature.................................................................... –65°C to +150°C Ambient Temperature with Power Applied................................... –40°C to +85°C Supply Voltage to Ground Potential (Input & VCC Only).............. –0.5V to +4.6V Supply Voltage to Ground Potential (Outputs & D/O Only).......... –0.5V to +4.6V DC Input Voltage............................................................................–0.5V to +5.5V DC Output Current....................................................................................... 120mA Power Dissipation........................................................................................... 1.0W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over Operating Range, TA = –40°C to +85°C, VCC = 3.3V ± 10%) Description Test Conditions(1) Min VIH VIL Input HIGH Voltage Input LOW Voltage Guaranteed Logic HIGH Level Guaranteed Logic Low Level 2.0 –0.5 IIH IIL IOZH VIK Input HIGH Current Input LOW Current High-Impedance Output Current Clamp Diode Voltage RON Switch On Resistance(3) Parameters VCC = Max, VIN = VCC VCC = Max, VIN = GND 0 ≤ A, B ≤ VCC VCC = Min, IIN = –18mA VCC = Min, VIN = 0.0V ION = 48mA or 64mA VCC = Min, VIN = 0.0V ION = 48mA or 64mA Capacitance (TA = 25°C, f = 1 MHz) Parameters(4) Description CIN Input Capacitance COFF A/B Capacitance, Switch Off CON A/B Capacitance, Switch On Test Conditions VIN = 0V Typ. 3.5 5.0 10.0 Typ.(2) Max Units V 0.8 –0.73 5 ±1 ±1 ±1 –1.2 7 8 15 µA V Ω Units pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 4. This parameter is determined by device characterization but is not production tested. 11-0008 2 PS8757G 11/25/10 PI3C3384 2.5V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch Power Supply Characteristics Parameters Description ICC Quiescent Power Supply Current DICC Supply Current per Input @ TTL HIGH Test Conditions(1) VCC = Max, VIN = GND or VCC VCC = Max, VIN = 3.0V(3) Min. Typ.(2) 260 Max. 500 Units µA 750 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25°C ambient. 3. Per TTL driven input (control inputs only); A and B pins do not contribute to ICC. Switching Characteristics over 3.3V Operating Range Parameters Description Conditions(1) (2,3) tPLH tPHL tPZH tPZL tPHZ tPLZ Propogation Delay Ax to Bx, Bx to Ax Bus Enable Time BEx to Ax or Bx Bus Disable Time BEx to Ax or Bx CL = 50pF RL = 500-ohm CL = 50pF RL = 500-ohm R = 500-ohm Com. Min Max 0.25 1.5 6.5 1.5 5.5 Switching Characteristics over 2.5V Operating Range Parameters Description Conditions(1) (2,3) tPLH tPHL tPZH tPZL tPHZ tPLZ Propogation Delay Ax to Bx, Bx to Ax Bus Enable Time BEx to Ax or Bx Bus Disable Time BEx to Ax or Bx CL = 50pF RL = 500-ohm CL = 50pF RL = 500-ohm R = 500-ohm Units Com. ns Units Min Max 0.25 1.5 9.8 1.5 8.3 ns Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 11-0008 3 PS8757G 11/25/10 PI3C3384 2.5V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch 4.0 VCC = 3.3V 3.8V 3.6V 3.4V 3.2V 3.0V 3.1V 2.9V 2.7V 2.5V VOUT, (V) 2.3V 2.8V 2.0 0.0 0.0 1.0 2.0 VIN, (V) 3.0 4.0 5.0 Output Voltage vs. Input Voltage over Various Supply Voltages Switch Position Test Circuit 6V VCC Open 500Ω VIN Pulse Generator VOUT 50pF 500Ω CL Enable and Disable Timing 3V 1.6V Control Input 1.5V Same Phase Input Transisiton 0V Switch Output Normally Low 0V 3V tPLH 3V 1.5V t PZH 0.3V VOL Output t PZH Switch GND 1.5V 0.3V 0V tPHL VOH 1.5V 1.5V VOL VOH tPLH tPHL 0V Opposite Phase Input Transisiton 1. Input Control Enable = Low Input Control Device = High 2. Pulse Generator total pulses Rate ≤1.0 MHz; Z OUT ≤50-Ohms; tF, tR ≤2.5ns 11-0008 3V 1.5V 1.5V t PLZ t PZL Output Normally High Propagation Delay Disable Enable Switch 6V 6V GND GND Open Definitions: CL = Load capacitance (includes jig and probe capacitance) RT = Termination resistance (should be equal to ZOUT of the pulse generator) D.U.T. RT Test Disable LOW Enable LOW Disable HIGH Enable HIGH tPD 4 3V 1.5V 0V PS8757G 11/25/10 PI3C3384 2.5V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch DOCUMENT CONTROL NO. PD - 1203 24 .008 0.20 MIN. .150 .157 3.81 3.99 0˚-6˚ .016 .035 0.41 0.89 Detail A 1 .041 1.04 REF 8.56 8.74 .033 0.84 .053 .069 .015 x 45˚ 0.38 1.35 1.75 Detail A 1 SEATING PLANE .025 typical 0.635 DATE: 10/22/07 .008 .013 0.20 0.33 Guage Plane .010 0.254 .337 .344 REVISION: H .008 0.203 .012 0.305 .004 0.101 .010 0.254 .007 .010 0.178 0.254 .228 .244 5.79 6.20 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Note: 1) Controlling dimensions in millimeters 2) Ref: JEDEC MO-137B/AE 3) Dimensions do not include mold flash, protrusions or gate burrs DESCRIPTION: 24-Pin, 150-Mil Wide, QSOP PACKAGE CODE: Q 07-0475 Ordering Information Ordering Code Package Code PI3C3384QE Q Package Description Pb-Free & Green, 24-pin QSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. E = Pb-free and Green 3. Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336  •  www.pericom.com 11-0008 5 PS8757G 11/25/10