PI3CH800QE

PI3CH800 8-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description     -    Applications         Pin Configuration TSSOP QSOP Block Diagram TQFN Truth Table(1) Pin Description Pin No 19 2, 3, 4, 5, 6, 7, 8, 9 Pin Name EN Description Switch Enables A0-A7 A Ports 10 GND Ground 11, 12, 13, 14, 15, 16, 17, 18 B0-B7 B Ports 20 VCC Power 1111111 Ax Function EN H Hi-Z Disconnect L Bx Connect Note: PI3CH800 Document Number DS40809 Rev 1-2 1. H=High Voltage Level; L=Low Voltage Level; Hi-Z=High Impedance www.diodes.com 1 March 2018 © Diodes Incorporated PI3CH800 Maximum Ratings Storage Temperature ................................................................................... -65oC to +150oC Ambient Temperature with Power Applied........................................–40°C to +85°C Supply Voltage to Ground Potential ............................................................-0.5V to + 4.6V DC Input Voltage ............................................................................................-0.5V to + 6.0V DC Output Current .......................................................................................... 120mA Power Dissipation .............................................................................................................. 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condi-tions above those indicated in the operational sec-tions of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics 3.3V supply (Over operating range, TA = -40 ~ +85ºC, VCC=3.3V±10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.5 - 0.8 V VIK Clamp Diode Voltage VCC = Min., IIN = -18mA - -1.3 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA IOZH High-Impedance Current - - ±1 μA - 4 6 RON Switch On-Resistance(3) 0 ≤ A, B ≤ VCC VCC = Min., VIN = 0.0V ION = -48mA or -64mA VCC = Min., VIN = 3.6V ION = -15mA - 5 8 Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. 2.5V supply (Over operating range, TA = -40 ~ +85ºC, VCC=2.5V±10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 - VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.8 V VIK Clamp Diode Voltage VCC = Max., IIN = -6mA - -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA IOZH High-Impedance Current - - ±1 μA - 4 8 RON Switch On-Resistance(3) 0 ≤ A, B ≤ VCC VCC = Min., VIN = 0.0V ION = -48mA VCC = Min., VIN = 2.25V ION = -15mA - 7 14 Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 2.5V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 2 March 2018 © Diodes Incorporated PI3CH800 1.8V supply (Over operating range, TA = -40 ~ +85ºC, VCC=1.8V±10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.2 - VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.6 V VIK Clamp Diode Voltage VCC = Max., IIN = -6mA - -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA IOZH High-Impedance Current - - ±1 μA - 4 8 RON Switch On-Resistance(3) 0 ≤ A, B ≤ VCC VCC = Min., VIN = 0.0V ION = -48mA VCC = Min., VIN = 2.25V ION = -15mA - 10 25 Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. Capacitance (TA = 25ºC, f=1MHz) Symbol(1) Description CIN Input Capacitance COFF A/B Capacitance, Switch Off CON A/B Capacitance, Switch On Typ(2) Test Conditions Unit 2.0 VIN = 0V 3.5 pF 7.0 Note: 1. These parameters are determined by device characterization but are not production tested Power Supply Characteristics Symbol Description Test Conditions(1) ICC Quiescent Power Supply Current VCC = 3.6V, VIN = GND or VCC Min Typ - 0.2 Max Unit 0.5 mA Note: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at +25°C ambient Dynamic Electrical Characteristics (Over Operating Range, TA = -40 ~ +85ºC, VCC=3.3V±10%) Symbol Description Test Conditions Min Typ Max XTALK Crosstalk 10MHz - -60 - OIRR Off-Isolation 10MHz - -60 - BW -3dB Bandwidth See test Diagram - 500 - PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 3 Unit dB MHz March 2018 © Diodes Incorporated PI3CH800 Switch Characteristics Over 3.3V Operating Range Symbol Test Conditions(1) Description (2, 3) Ax to Bx, Bx to Ax Min Typ Max See test Diagram - - 0.3 tPLH, tPHL Propagation Delay tPZH, tPZL Enable Time EN to Ax or Bx See test Diagram 1.5 - 9.0 tPHZ, tPLZ Disable Time EN to Ax or Bx See test Diagram 1.5 - 9.0 Unit ns Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Over 2.5V Operating Range Symbol Test Conditions(1) Description (2, 3) Ax to Bx, Bx to Ax Min Typ Max See test Diagram - - 0.3 tPLH, tPHL Propagation Delay tPZH, tPZL Enable Time EN to Ax or Bx See test Diagram 1.5 - 15.0 tPHZ, tPLZ Disable Time EN to Ax or Bx See test Diagram 1.5 - 12.0 Unit ns Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Over 1.8V Operating Range Symbol Test Conditions(1) Description (2, 3) Ax to Bx, Bx to Ax Min Typ Max See test Diagram - - 0.3 tPLH, tPHL Propagation Delay tPZH, tPZL Enable Time EN to Ax or Bx See test Diagram 1.5 - 25.0 tPHZ, tPLZ Disable Time EN to Ax or Bx See test Diagram 1.5 - 12.0 Unit ns Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 4 March 2018 © Diodes Incorporated PI3CH800 Test Circuit for Electrical Characteristics 6.0V VCC 200Ω Pulse Generator VIN VOUT D.U.T RT 10pF CL 200Ω Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. All input impulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50-ohm, tR ≤ 2.5ns, tF ≤ 2.5ns. 4. The outputs are measured one at a time with one transition per measurement. Switch Positions Te tPLZst, tPZL Switch tPHZ, tPZH GND Prop Delay Open 6.0V Test Circuit for Dynamic Electrical Characteristics PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 5 March 2018 © Diodes Incorporated PI3CH800 Switching Waveforms Voltage Waveforms Enable and Disable Times Applications Information Logic Inputs Hot Insertion Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. Part Marking L Package PI3CH800 Document Number DS40809 Rev 1-2 ZH Package Q Package www.diodes.com 6 March 2018 © Diodes Incorporated PI3CH800 Packaging Mechanical 20-TSSOP(L) PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 7 March 2018 © Diodes Incorporated PI3CH800 20-TQFN(ZH) PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 8 March 2018 © Diodes Incorporated PI3CH800 20-QSOP(Q) Ordering Information Part Number PI3CH800LEX PI3CH800ZHEX PI3CH800QEX Package Cede L ZH Q Package Description 20-Pin, 173mil-Wide (TSSOP) 20-Pin, Very Thin Quad Flat No-Lead (TQFN) 20-Pin, 150mil-Wide (QSOP) Notes: 1. EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. All applicable RoHS exemptions applied. 2. See http://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, “Green” and Lead-free. 3. Thermal characteristics can be found on the company web site at www.diodes.com/design/support/packaging/ 4. E = Pb-free and Green 5. X suffix = Tape/Reel PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 9 March 2018 © Diodes Incorporated PI3CH800 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com PI3CH800 Document Number DS40809 Rev 1-2 www.diodes.com 10 March 2018 © Diodes Incorporated