PI3HDMI412-BAE

PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Features Description • 3.3V VDD • 4-Differential Channel 2:1 Mux/DeMux • DVI, HDMI, 1.2 +1.2 signal compatible • Data Rate: 1.65Gbps • Supports both AC coupled and DC coupled signals • Crosstalk: -35dB@825MHz • Switching speed: 4ns • Isolation: -30dB@825MHz • Near-Zero Prop Delay: 250ps max. • Low bit-to-bit skew • Enable/Disable Time: 9ns • Bidirectional • Enhanced ESD Protection: - Switch pins: 1.1kV (machine model) 12kV (humanbody model) 8kV (contact)(1) • Packaging (Pb-free & Green): —48-pin TSSOP (A) Pericom Semiconductor’s PI3HDMI series of switch circuits are targeted for high-resolution video networks that are based on DVI/ HDMI standards, and TMDS signal processing. The PI3HDMI412-B is a 8- to 4-Channel Mux/DeMux Switch. The device multiplexes differential signals to one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew and high channel-to-channel noise isolation. The maximum DVI/HDMI data rate of 1.65Gbps provides the resolution required by the next generation HDTV and PC graphics. Three differential channels are used for data (video signals for DVI or audio/video signals for HDMI), and one differential channel is used for Clock for decoding the TMDS signals at the outputs. Because of its passive bidirectional feature, this switch can be used either at the video drivers side or at the receiver side. For PC graphics applications, the device sits at the drivers side to switch between multiple display units such as PC LCD monitor, projector, TV, etc. For consumer video applications, the device sits at the receiver end to switch between the source components such as DVD, D-VHS, STB, etc. Pin Configuration Block Diagram A0 0B1 A1 1B1 48 2 47 1B1 GND 3 46 GND 0B 2 A1 4 45 1B2 GND 5 44 1B 2 V DD 6 43 GND GND 7 42 2B 1 A2 8 41 3B 1 GND 9 40 GND 2B1 A3 3B1 2B2 A3 10 11 39 38 2B 2 GND 4B1 V DD 12 37 GND 5B1 GND 13 36 V DD 4B2 NC 14 35 4B1 3B2 A5 1 A0 0B2 A2 A4 0B1 V DD 5B2 3B 2 A4 15 34 5B1 GND 16 33 GND 4B 2 A6 6B1 A7 A5 17 7B1 32 GND 18 31 5B 2 6B2 V DD 19 30 GND GND 20 29 6B 1 A6 21 28 7B 1 GND 22 27 GND A7 23 24 26 6B 2 25 7B 2 7B2 SEL SEL Note: 1. IEC 61000-4-2 06-0050 1 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Truth Table Function(1) SEL Ax to xB1 L Ax to xB2 H Note: 1 x=0 through 7 Pin Description Pin # 3,5,7,9,11,13,16, 18,20,22,27,30,3 3,37,40,43,46 1,6,12,19,36 Pin Name GND Type Power Description Ground VDD Power Supply Voltage (3.3V ± 10%) 14 2 4 8 10 15 17 21 23 24 25 26 28 29 31 32 34 35 38 39 41 42 44 45 47 48 NC A0 A1 A2 A3 A4 A5 A6 A7 SEL 7B2 6B2 7B1 6B1 5B2 4B2 5B1 4B1 3B2 2B2 3B1 2B1 1B2 0B2 1B1 0B1 I/O I/O I/O I/O I/O I/O I/O I/O Input I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O No Connection TMDS Data 0TMDS Data 0+ TMDS Data 1TMDS Data 1+ TMDS Data 2TMDS Data 2+ TMDS Data 3TMDS Data 3+ Selection for Port 1 or Port 2 TMDS Data 3+ for Port 2 TMDS Data 3- for Port 2 TMDS Data 3+ for Port 1 TMDS Data 3- for Port 1 TMDS Data 2+ for Port 2 TMDS Data 2- for Port 2 TMDS Data 2+ for Port 1 TMDS Data 2- for Port 1 TMDS Data 1+ for Port 2 TMDS Data 1- for Port 2 TMDS Data 1+ for Port 1 TMDS Data 1- for Port 1 TMDS Data 0+ for Port 2 TMDS Data 0- for Port 2 TMDS Data 0+ for Port 1 TMDS Data 0- for Port 1 06-0050 2 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Maximum Ratings (Above which useful life may be impaired. For user guidelines, not tested.) Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Storage Temperature....................................–65°C to +150°C Supply Voltage...................................................-0.5V to 3.6V DC Input Voltage ...............................................0V to VDD DC Output Current......................................................120mA Power Dissipation...........................................................0.5W DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C, VDD = 3.3V ±10%) Description Test Conditions(1) Min. VIH(3) Input HIGH Voltage Guaranteed HIGH level 0.65 (VDD) VIL(3) Input LOW Voltage Guaranteed LOW level –0.5 VIK Clamp Diode Voltage VDD=Max., IIN=–18mA IIH Input HIGH Current VDD=Max., VIN=VDD ±5 IIL Input LOW Current VDD=Max., VIN=0V ±5 Paramenter Typ.(2) –0.7 Max. Units 0.35 (VDD) V –1.2 μA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25°C ambient and maximum loading. 3. VIH + VIL are for SEL input only. 06-0050 3 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Power Supply Characteristics Parameters ICC Test Conditions(1) Description Quiescent Power Supply Current Min. Typ.(2) VDD = Max., VIN = VDD or 0V Max. 500 Units μA Dynamic Electrical Characteristics Over the Operating Range (TA= -40º to +85ºC, VDD = 3.3V ±10%) Parameter Description Test Conditions Min. Typ.(2) Crosstalk See Fig. 1 for Measurement Setup, f = 825 MHz -35 OIRR OFF Isolation See Fig. 2 for Measurement Setup, f = 825 MHz -30 DR Data Rate XTALK Max. Units dB 1.65 Gbps Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25°C ambient and maximum loading.          
    Fig 1. Crosstalk Setup 06-0050 4 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard        
  
 
 
 
 Fig 2. Off-isolation setup Fig 3. Crosstalk 06-0050 5 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Fig 4. Off Isolation Switching Characteristics (TA= -40º to +85ºC, GND=0V, VDD=3.3V ±10%) Paramenter tPZH, tPZL tPHZ, tPLZ Description(1) Min. Typ. Max. Line Enable Time - SEL to AN, BN 0.5 - 8.0 Line Disable Time - SEL to AN, BN 0.5 - 4.0 Units Notes: 1. For measurement setup, please see “Test Circuit For Electrical Characteristic” on page 6, and “Switching waveforms” on page 7 06-0050 6 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Test Circuit for Electrical Characteristics 

    
       Notes: • CL = Load capacitance: includes jig and probe capacitance. • RT = Termination resistance: should be equal to ZOUT of the Pulse Generator • Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. • All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns. • The outputs are measured one at a time with one transition per measurement. Switch Positions Test Switch tPLZ, tPZL (output on B-side) 2 x (VDD) tPHZ, tPZH (output on B-side) Gnd Prop Delay Open Test Circuit for Dynamic Electrical Characteristics  

      06-0050 7 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Switching Waveforms     
     
 


     

 
     
 Voltage Waveforms Enable and Disable Times TP3 Rx Test Setup 06-0050 8 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard TP3 eye diagrams with 3 meter cables With No Switch With Switch Packaging Mechanical: 48-pin TSSOP (A)            -AX 3%!4).'0,!.%     888 888 $%./4%3$)-%.3)/.3 ).-),,)-%4%23  "3#               "3#  Ordering Information Ordering Code PI3HDMI412-BAE Package Code Package Description A Pb-free & Green, 48-pin TSSOP Notes: • Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ • E = Pb-free and Green Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 06-0050 9 PS8809B 04/26/06