PI3HDMI412FT-BZHE

PI3HDMI412FT-B 2:1 Mux/DeMux High Bandwidth HDMI™ 1.4 Compliant Signal Switch Features Description ÎÎ4-Differential Channel 2:1 Mux/DeMux Pericom Semiconductor’s PI3HDMI series of switch circuits are targeted for high-resolution video networks that are based on DVI/HDMITM standards, and TMDS signal processing. The PI3HDMI412FT-B is an 8- to 4-Channel Mux/DeMux Switch. The device multiplexes differential signals to one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew and high channel-to-channel noise isolation. ÎÎHDMI TM 1.4 compatible ÎÎHigh Bandwidth: 2.7GHz @-3dB BW ÎÎSupports both AC coupled and DC coupled signals ÎÎSwitching speed: 4ns ÎÎIsolation: -40dB @ 2.0 Gbps ÎÎCrosstalk: -31dB @ 2.0 Gbps ÎÎESD: Data bits @ 8kV contact, select bit @ 2kV HBM The high bandwidth provides the resolution required by the next generation HDTV and PC graphics. Three differential channels are used for data (video signals for DVI or audio/video signals for HDMI), and one differential channel is used for Clock for decoding the TMDS signals at the outputs. ÎÎLow bit-to-bit skew ÎÎEnable/Disable Time: 9ns ÎÎBidirectional ÎÎPackaging (Pb-free & Green): Because of its passive bidirectional feature, this switch can be used either at the video drivers side or at the receiver side. For PC graphics applications, the device sits at the drivers side to switch between multiple display units such as LCD monitor, projector, TV, etc. For consumer video applications, the device sits at the receiver end to switch between the source components such as DVD, D-VHS, STB, etc. — 42-pin TQFN (ZH42) — 48-pin BQSOP (B48) Pin Description Block Diagram 48-pin BQSOP VDD VSS VDD VSS 42-pin TQFN D0+ D0D1+ D1D2+ D2D3+ D3- D0+A D0-A D1+A D1-A D2+A D2-A D3+A D3-A D0+B D0-B D1+B D1-B D2+B D2-B D3+B D3-B VSS VDD D0+ D0VSS D1+ D1VDD SEL VSS D2+ D2VSS D3+ D3VDD VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 42 41 40 39 VSS 18 19 20 21 VDD VSS VDD VSS SEL 13-0006 1 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 D0+A D0-A D1+A D1-A D2+A D2-A D3+A D3-A VDD D0+B D0-B D1+B D1-B D2+B D2-B D3+B D3-B VSS VDD VSS VDD VSS D0+ D0VSS D1+ D1VSS VDD SEL VSS D2+ D2VSS D3+ D3VSS VDD VSS VDD VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 PS8905A VDD VSS D0+A D0-A D1+A D1-A VSS D2+A D2-A D3+A D3-A VSS VDD D0+B D0-B D1+B D1-B VSS D2+B D2-B D3+B D3-B VSS VDD 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Pin Description Pin # (BQSOP) Pin # (TQFN) Pin Name Description 2, 4, 12, 21, 23, 25, 36, 48 2, 8, 16, 18, 20, 30, 40, 42 VDD + Power supply 1, 3, 5, 8, 11, 14, 17, 20, 22, 24, 26, 31, 37, 42, 47 1, 5, 10, 13, 17, 19, 21, 39, 41 VSS - Power supply 13 9 SEL Select pin, see truth table 6, 7, 9, 10, 15, 16, 18, 19, 2730, 32-35, 38-41, 43-36 3, 4, 6, 7, 11, 12, 14, 15, 2229, 31-38 Dx+/-x + CLK+/-x Data + Clk bits for TMDS signal Truth Table(1) Function SEL Dx to Dx A L Dx to Dx H B Note: 1. x=0,1,2,3 Maximum Ratings (Above which useful life may be impaired. For user guidelines, not tested.) Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Storage Temperature...........................................................–65°C to +150°C Supply Voltage to VSS Potential............................................–0.5V to +2.5V DC Input Voltage ..............................................................0V to VDD+0.5V DC Output Current.............................................................................120mA DC Power Supply Characteristics Parameter Description Min. Max. Units VDD - VSS Positive to Negative Power Supply 1.5 2.0 V VSS Negative Power Supply 0 1.6 V DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C) Parameter Description Test Conditions (1) Min. VIH(3) Input HIGH Voltage Guaranteed HIGH level 0.65(VDD -VSS)+VSS VIL Input LOW Voltage Guaranteed LOW level –0.5+VSS (3) Typ.(2) –0.7+VSS Max. Units 0.35(VDD -VSS)+VSS V VIK Clamp Diode Voltage VDD =Max., IIN=–18mA –1.2+VSS IIH Input HIGH Current VDD =Max., VIN=VDD ±5 IIL Input LOW Current VDD =Max., VIN=VSS ±5 µA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Ta = 25°C ambient and maximum loading. 3. VIH & VIL are for SEL input only. 13-0006 2 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Power Supply Characteristics Parameters Description Test Conditions(1) ICC Quiescent Power Supply Current Min. Typ.(2) Max. Units 300 400 µA Min. Max. Units 0.5 8.0 0.5 4.0 VDD = Max., VIN = VDD or VSS Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Ta = 25°C ambient and maximum loading. Switching Characteristics (TA= -40º to +85ºC, VSS=0V, VDD=1.8V ±10%) Parameter Description tPZH, tPZL Line Enable Time - SEL to N , N tPHZ , tPLZ Line Disable Time - SEL to N , N A A B (1) B (1) ns Notes: 1. For measurement setup, please see “Test Circuit For Electrical Characteristic” on page 8, and “Switching waveforms” on page 9 Dynamic Electrical Characteristics Over the Operating Range (TA= -40º to +85ºC) Parameter Description XTALK Crosstalk OIRR OFF Isolation BW -3dB BW Insertion Loss 13-0006 Test Conditions Min. See Fig. 1 for Measurement Setup, @ 2.0 Gbps See Fig. 2 for Measurement Setup, @ 2.0 Gbps Typ. Max. -31 dB -40 2.7 @ 1.65 Gbps -0.87 @ 2.0 Gbps -0.95 @ 2.5 Gbps -1.18 @ 3.3 Gbps -1.85 3 Units GHz dB PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch HP13963 R S HP11667A T PI3HDMI412FT-B 50-ohm 100 -ohm 50-ohm 50-ohm 100 -ohm Fig 1. Crosstalk Setup HP4396B R S T HP11667A 50-ohm PI3HDMI412FT-B 50-ohm 50-ohm 100 -ohm Fig 2. Off-isolation setup 13-0006 4 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Fig 3. Crosstalk 13-0006 5 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Fig 4. Off Isolation 13-0006 6 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Fig 5. Insertion Loss 13-0006 7 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Application Measurements Agilent 54855A scope Agilent N4901A pattern generator + - CH3 Clock PI3HDMI412FT-B Clock 3.3V + 2 meter DVI cable - TP3 Pericom test board CH4 Row Clock 3.3V Silicon Image TPA2-R fixture Clock + Silicon Image CRU clock recover board Fig 6. TMDS TP3 Rx eye compliance Test Setup 13-0006 8 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Fig 7. TP3 (Rx) with 2-meter cable eye measurements (Right eye is with no switch. Left eye is with switch.) Test Circuit for Electrical Characteristics 2 x VDD VDD 200-ohm Pulse Generator VIN VOUT D.U.T 4pF CL RT 200-ohm Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 4. All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns. 5. The outputs are measured one at a time with one transition per measurement. 13-0006 9 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Switch Positions Test Switch tPLZ , tPZL 2 x (VDD - VSS) tPHZ , tPZH VSS Prop Delay Open Test Circuit for Dynamic Electrical Characteristics R1 S1 T1 PI3HDMI412FT-B HP11667A Switching Waveforms Voltage Waveforms Enable and Disable Times 13-0006 10 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch 3.3V PI3HDMI412FT-C 1.8k-ohm 3.3V Select Line 1.5k-ohm 1.5V Select Line Example of a circuit that also needs to be connected to the select lines of the PI3HDMI412FT-B Packaging Mechanical: 42-Pin TQFN (ZH) Notes: 1. All dimensions are in millimeters. Angles in degrees. 2. Coplanarity applies to the exposed pad as well as the terminals. 3. Refer JEDEC MO-220. 4. Recommended land pattern is for reference only. 5. Thermal pad soldering area DATE: 11/14/12 DESCRIPTION: 42-contact Thin Fine Pitch Quad Flat No-Lead (TQFN) PACKAGE CODE: ZH42 DOCUMENT CONTROL #: PD-2035 REVISION:D Note: 12-0529 • For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php 13-0006 11 PS8905A 12/10/12 PI3HDMI412FT-B 2:1 Mux/DeMux High BW HDMI™ 1.4 Compliant Signal Switch Packaging Mechanical: 48-Pin BQSOP (B) 1 DATE: 10/15/08 DESCRIPTION: 48-Pin, 154-Mil Wide BQSOP PACKAGE CODE: B48 DOCUMENT CONTROL #: PD-1210 Note: REVISION: F 08-0522 • For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php Ordering Information Ordering Code Package Code Package Description PI3HDMI412FT-BZHE ZH Pb-free & Green, 42-pin TQFN PI3HDMI412FT-BBE B Pb-free & Green, 48-pin BQSOP Notes: • Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ • E = Pb-free and Green • Adding X suffix = Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336  •  www.pericom.com 13-0006 All trademarks are property of their respective owners. 12 PS8905A 12/10/12