PI5A4599BCEX

PI5A4599B SOTiny TM Low Resistance, Low-Voltage Single-Supply SPDT Switch Description Features           Applications       Pin Assignment Pin Description Pin No Pin Name Description 1 2 3 4 5 6 IN V+ GND NC COM NO Logic control Positive Power Supply Ground Data Port (Normally connected) Common Output/Data Port Data Port PI5A4599B Logic Function Table PI5A4599B Document Number DS40257 Rev 1-2 Logic Inputs(IN) NC NO 0 ON OFF 1 OFF ON www.diodes.com 1 September 2017 © Diodes Incorporated PI5A4599B Maximum Ratings Storage Temperature…………………………………...-65℃ to +150℃ Ambient Temperature with Power Applied......................-40℃ to +85℃ Supply Voltage V+ …………………………………..…..-0.5V to +7.0V DC Switch Voltage VIN ……………………………-0.5V to V+ +0.5V DC Input Voltage VINPUT … …………………………..-0.5V to +7.0V DC Output Current VOUT… …………………………….…….….128mA DC V+ or Ground Current I+ /IGND … ……………….…….…±100mA Junction Temperature under Bias (TJ) ............................................150°C Junction Lead Temperature (TL) (Soldering, 10 seconds) .................................................................. 260°C Power Dissipation (PD) @ +85°C .................................................180mW Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended Operating Conditions Symbol V+ VIN VS VOUT TA Parameter Operating Voltage Control Input Voltage Switch Input Voltage Output Voltage Operating Temperature Conditions Control Input V+ = 2.3V to 3.6V Input Rise and Fall Time tr, tf Control Input V+ = 4.5V to 6.0V Note: Control input must be held HIGH or LOW; it must not float. PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 2 Min. 1.65 0 0 0 -40 0 0 Typ. 25 - Max. 6.0 V+ V+ V+ 85 10 5 Unit V V V V °C ns/V ns/V September 2017 © Diodes Incorporated PI5A4599B DC Electrical Characteristics (TA = –40°C to 85°C, unless otherwise noted.) Parameter Description Test Conditions VIAR Analog Input Signal Range V+ V+=4.5V, IO = 30mA, VINPUT = 0V V+=4.5V, IO=-30mA, VINPUT =2.4V V+=4.5V, IO =-30mA, VINPUT =4.5V V+=4.5V, IO =30mA, VINPUT = 0V V+=4.5V, IO =-30mA,VINPUT =2.4V V+=4.5V, IO =-30mA, VINPUT =4.5V V+=3.0V, IO =24mA, VINPUT =0V V+=3.0V, IO =-24mA, VINPUT =3.0V V+=3.0V, IO =24mA, VINPUT =0V V+=3.0V, IO=-24mA, VINPUT =3.0V V+=2.3V, IO =8mA, VINPUT =0V V+=2.3V, IO =-8mA, VINPUT =2.3V V+=2.3V, IO =8mA, VINPUT =0V V+=2.3V, IO=-8mA, VINPUT =2.3V V+=1.65V, IO =4mA, VINPUT =0V V+=1.65V, IO=-4mA, VINPUT=1.65V V+=1.65V, IO =4mA, VINPUT= 0V V+=1.65V, IO=-4mA, VINPUT=1.65V V+=4.5V, IA=-30mA, VINPUT=3.15V V+=3.0V, IA=-24mA, VINPUT =2.1V V+=2.3V, IA =-8mA, VINPUT =1.6V V+=1.65V, IA=-4mA, VINPUT=1.15V V+=5.0V, IA =-30mA,0≤VINPUT≤V+ V+=3.3V, IA =V+ 24mA,0≤VINPUT V+=2.5V, IA =-8mA, 0≤VINPUT≤V+ V+=1.8V, IA =-4mA, 0≤VINPUT≤V+ V+=1.65V V+ = 2.3V V+ = 3V V+ = 4.2V V+ = 5.5V V+=1.65V V+ = 2.3V V+ = 3V V+ = 4.2V V+ =5.5V RON ∆RON RONF (1) ON Resistance ON Resistance Match (1,2,3) Between Channels ON Resistance (1,2,4) Flatness VIH Input High Voltage (Logic High Level) VIL Input Low Voltage (Logic Low Level) ILKC Input Leakage Current 0≤VIN≤5.5V, V+=0V to 5.5V IOFF OFF State Leakage Current 0≤VIN≤5.5V, V+=1.65V to 5.5V I+ Quiescent Supply Current All channels ON or OFF, VIN = V+ or GND, IOUT=0, V+ = 5.5V V Temperature (TA:ºC) -40°C to 85°C 25°C -40°C to 85°C 25°C -40°C to 85°C 25°C -40°C to 85°C 25°C -40°C to 85°C 25°C 25°C -40°C to 85°C -40°C to 85°C 25°C -40°C to 85°C 25°C -40°Cto 85°C 25°C -40°C to 85°C Min. Typ. Max. Units 0 - 4 5 7 5 10 6 13 8 20 0.15 0.2 0.3 0.5 4.6 V+ 6 8 11 6 8 11 8 15 8 15 9 20 9 20 12 30 12 25 - V - 7 - 1 1.2 1.3 1.5 1.8 - 15 77 - 0.4 0.6 0.8 1 1.2 ±0.1 ±1.0 ±0.1 ±10 1 5    V V µA µA µA Notes: 1. Measured by voltage drop between COM and NC/NO pins at the indicated current through the device. ON resistance is determined by the lower of the voltages on two ports (COM or NC/NO). 2. Parameter is characterized but not tested in production. 3. ∆RON = RON max – RON min. measured at identical V+, temperature and voltage levels. 4. Flatness is defined as difference between maximum and minimum value of ON resistance over the specified range of conditions. Guaranteed by design. PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 3 September 2017 © Diodes Incorporated PI5A4599B Capacitance (1) (TA = 25°C, unless otherwise noted.) Symbol Parameter CIN Control Input COFF NC/NO Port, Switch OFF Test Conditions (1) Min. - Typ. 2.5 5.0 Max. - - 15.0 - Units pF V+ = 5.0V, f =1 MHz CCOM ON COM Port, Switch ON Notes: 1. Capacitance is characterized but not tested in production Switch and AC Characteristics (1) Parameter tON tOFF Description Turn-On Time Turn-Off Time Supply Voltage Test Conditions V+ =3.3V, VNO or VNO=1.5V, VIL=1.5V, RL=100Ω, CL=35pF, See Test Circuit Figure 1. V+ =5.0V, VNO or VNO=3V, VIL=3V, - 5 25 - 3 15 - 2 12 - 1.5 7 0.5 - - 0.5 - - V+ =3.0V to 3.6V 0.5 - - V+ =4.5V to 5.5V 0.5 - - - 5 - - 4 - - -82 - V+ =3.3V, VNO or VNO=1.5V, VIL=1.5V, RL=100Ω, CL=35pF, See Test Circuit Figure 1. Temperature Min. Typ. Max. Units (TA: ºC) +25°C +25°C V+ =5.0V, VNO or VNO=3V, VIL=3V, V+ =1.65V to 1.95V tBM Q OIRR Break Before Make Time Charge Injection Off Isolation V+ =2.3V to 2.7V See Test Circuit Figure2. CL = 0.1nF, VGEN = 0V, RGEN=0 . See Test Circuit Figure 3. RL=50, VGEN=0V, RGEN =0, f =1MHz. -40 to 85°C V+ = 5.0V 25°C V+ = 3.3V V+ =1.65V to 5.5V 25°C ns pC (3) XTALK Crosstalk Isolation dB See test circuit 5 RL=50, VGEN=0V, RGEN =0, f =1MHz. V+ =1.65V to 5.5V 25°C - -82 - V+ =1.65V to 5.5V 25°C - 350 - (4) f3dB –3dB Bandwidth See test circuit 6 See Test Circuit Figure 8 MHz Notes: 1. Guaranteed by design. 2. The device contributes no other propagation delay other than the RC delay of the switch ON resistance and the 50pF load capacitance, when driven by an ideal voltage source with zero output impedance. 3. Off Isolation = 20 Log10 [VNC (or VNO)/VCOM] and is measured in dB. 4. Crosstalk Isolation = 20 Log10 [VNO/VNC ] and is measured in dB. PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 4 September 2017 © Diodes Incorporated PI5A4599B Test Circuits and Timing Diagrams Figure 1. Switching Time VINPUT NC COM NO IN Figure 2. Break Before Make Interval Timing PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 5 September 2017 © Diodes Incorporated PI5A4599B NC or NO COM IN Figure 3. Charge Injection Test V+ COM V+ V+ V+ NC 0V or VIH COM NO IN NC IN Figure 5. Crosstalk Figure 4. Off Isolation V+ V+ COM V+ COM 0V or VIH 0V or VIH IN IN NC NC Figure 6. Channel Off Capacitance PI5A4599B Document Number DS40257 Rev 1-2 V+ Figure 7. Channel On Capacitance www.diodes.com 6 September 2017 © Diodes Incorporated PI5A4599B V+ V+ NO COM IN 0V or VIH Figure 8. Bandwidth PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 7 September 2017 © Diodes Incorporated PI5A4599B Mechanical Information C-6 (SC70) Ordering Information Part Number Package Code Package Top Marking PI5A4599BCEX C 6-Pin, SOT363 (SC70) nK Notes:  Thermal characteristics can be found on the company web site at www.diodes.com/design/support/packaging/  E = Pb-free and Green  X suffix = Tape/Reel PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 8 September 2017 © Diodes Incorporated PI5A4599B IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com PI5A4599B Document Number DS40257 Rev 1-2 www.diodes.com 9 September 2017 © Diodes Incorporated