PI5L200LEX

A product Line of Diodes Incorporated PI5L200 Precision Wide Bandwidth LanSwitch Quad 2:1 Mux/DeMux Features Description ¼¼ Single 3.3V/5V supply operation ¼¼ Rail-To-Rail Operation ¼¼ Very Low Distortion: 2% ¼¼ Replaces mechanical relays ¼¼ High-performance, low-cost solution for switching between different LAN signals ¼¼ Low crosstalk: –70dB @ 30 Mbps ¼¼ Low insertion loss and On-Resistance: 6-ohms typical ¼¼ Off isolation: –55dB @ 30 Mbps ¼¼ Wide bandwidth data rates >135 Mbps ¼¼ Low Quiescent Supply Current (100nA typical) ¼¼ Packaging (Pb-free & Green available): – 16-pin 150-mil wide plastic QSOP (Q) – 16-pin 150-mil wide plastic SOIC (W) – 16-pin 173-mil wide plastic TSSOP (L) Diodes' PI5L200 is a Rail-to-Rail Quad 2:1 multiplexer/demultiplexer LanSwitch with 3-state outputs. The On-Resistance typically varies from 5 ohms to 7 ohms with data inputs of 0V to 5V. Generally, this part can be used to replace mechanical relays in low voltage (3.3V/5V systems) LAN applications. With a wide bandwidth of 135 MHz, the PI5L200 can switch Fast Ethernet and ATM25 signals. Into 100-ohm UTP cables, the switch distortion is typically less than two percent. Crosstalk @30 MHz is –70dB. The PI5L200 operates from a single 3.3V/5V supply and interface to TTL logic. Pin Configuration Applications ¼¼ 10/100 Base-TX/T4 ¼¼ 100VG-AnyLAN ¼¼ Token Ring 4/16 Mbps ¼¼ ATM25 ¼¼ NIC Adapter and Hubs ¼¼ SONET OCI 51.8Mbps ¼¼ T1/E1 Block Diagram YA IA1 IB0 YB IB1 IC0 YC IC1 16 VCC 2 15 E IA1 3 14 ID0 YA 4 13 ID1 IB0 5 12 YD IB1 6 11 IC0 YB 7 10 IC1 GND 8 9 YC Pin Name Description IAn-IDn Data Inputs S Select Inputs E Enable YA-YD Data Outputs GND Ground VCC Power Truth Table ID0 YD ID1 Decoder/Driver E Document Number DS40562 Rev 1-2 1 Pin Description IA0 PI5L200 S IA0 E S YA YB YC YD Function H X Hi-Z Hi-Z Hi-Z Hi-Z Disable L L IA0 IB0 IC0 I D0 S=0 L H IA1 IB1 IC1 I D1 S=1 Note: H = High Voltage Level, L = Low Voltage Level, S witches are shown with logic "0" input (Select and Enable) S 1 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature........................................................... –65°C to +150°C Ambient Temperature with Power Applied.......................... –40°C to +85°C Supply Voltage to Ground Potential ...................................... –0.5V to +7.0V DC Input Voltage............................................................ –0.5V to VCC+0.5V DC Output Current............................................................................. 120 mA Power Dissipation.................................................................................. 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Single 5.0V Supply DC Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 5V ±10%, GND = 0V) Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units VANALOG Analog Signal Range 0 - VCC V RON ON-Resistance - 6 12 ∆RON Match Between Channels - 0.4 2 RFLAT(ON) RON Flatness ION = 1mA, VNO, VNC = 0V to 5V - 3 5 INO(OFF), INO(ON) On/Off Leakage Current VNO, VNC = 4.5V −100 - 100 nA ICC Quiescent Supply Current VCC = 5.5V, VIN = 0V or VCC - - 1 µA IO Output Current VNO, VNC or VCOM = 0V to 5V 100 - - mA VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - VIL Input LOW Voltage Guaranteed Logic LOW Level −0.5 - 0.8 IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 IIL Input LOW Current VCC = Max., VIN = GND - - ±1 ION = 10mA to 30mA Ω V µA Dynamic Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 5V ±10%, GND = 0V) Parameters Description Test Conditions(1) Min. Typ.(2) Max. tON Turn-on Time tOFF VON or VNC = 3.0V, see Fig. 2 - 10 20 Turn-off Time VON or VNC = 3.0V, see Fig. 2 - 5 10 XTALK Crosstalk RL = 100 ohms, f = 30 MHz, see Fig. 4 - −70 - dB C(OFF) NC or NO Capacitance f = 1 kHz - 13 - pF OIRR Off Isolation RL = 100 ohms, f = 30 MHz, see Fig. 5 - −55 - dB BW Bandwidth -3dB RL = 100 ohms, see Fig. 3 - 137 - MHz 2 - % RL = 100 ohms D Distortion DRON/RL Note: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for applicable device type. 2. Guaranteed by design. PI5L200 Document Number DS40562 Rev 1-2 2 www.diodes.com Units ns January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 Single 3.3V Supply DC Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 3.3V ±10%, GND = 0V) Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units VANALOG Analog Signal Range 0 - VCC V RON ON-Resistance - 15 22 ∆RON Match Between Channels - 1 3 RFLAT(ON) RON Flatness ION = 1mA, VNO, VNC = 0V to 5V - 7 12 INO(OFF), INO(ON) On/Off Leakage Current VNO, VNC = 3.0V −100 - 100 nA ICOM(ON) On Leakage Current VNO, VNC = 3.0V −100 - 100 µA IO Output Current VNO, VNC or VCOM = 0V 80 - - mA VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - VIL Input LOW Voltage Guaranteed Logic LOW Level −0.5 - 0.8 IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 IIL Input LOW Current VCC = Max., VIN = GND - - ±1 ION = 10mA to 30mA Ω V µA Dynamic Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 3.3V ±10%, GND = 0V) Parameters Description Test Conditions(1) Min. Typ.(2) Max. tON Turn-on Time tOFF Units VON or VNC = 1.5V, see Fig. 2 - 28 40 Turn-off Time VON or VNC = 1.5V, see Fig. 2 - 4 20 XTALK Crosstalk RL = 50 ohms, f = 1 MHz, see Fig. 4 - −75 - C(OFF) NC or NO Capacitance f = 1 kHz - 15 - CCOM(OFF) COM Off Capacitance f = 1 kHz - 30 - OIRR Off Isolation RL = 50 ohms, f = 1 MHz, see Fig. 5 - −75 - dB BW Bandwidth -3dB RL = 50 ohms, see Fig. 3 - 110 - MHz D Distortion RL = 100 ohms - 4 - % ns dB pF Dynamic Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 3.3V ±10%, GND = 0V) Parameters Description Test Conditions(1) ICC Quiescent Positive Power Supply Current VCC = 3.6V, VIN = 0V or VCC All Channesl ON or OFF Min. Typ.(2) Max. Units - - 1 µA Note: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for applicable device type. 2. Guaranteed by design. PI5L200 Document Number DS40562 Rev 1-2 3 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 TRANSMIT TX RX RECEIVE Figure 1a. Full Duplex Transceiver TX1 100Ω 120Ω RX1 Figure 1b. Loop Back Figure 1d. Line Clamp Figure 1c. Line Termination Test Circuits Vcc DIGITAL INPUT Vcc In 3V Y VOUT 100W S GND ANALOG OUTPUT 35pF E 50% 90% tON 50% 90% tOFF Figure 2. Switching Time PI5L200 Document Number DS40562 Rev 1-2 4 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 ACTIVE PROBE HP4195 NETWORK ANALYZER VOUT 100Ω 100Ω 50Ω S E1 +5V Figure 3. Bandwidth ACTIVE PROBE HP4195 NETWORK ANALYZER IA0 YA 100Ω 100Ω YA IC0 VOUT 100Ω 50Ω S E Figure 4. Crosstalk ACTIVE PROBE HP4195 NETWORK ANALYZER Y I0 50Ω VOUT 100Ω I1 S E 50Ω Figure 5. Off Isolation PI5L200 Document Number DS40562 Rev 1-2 5 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 RH = 100Ω TA = 25°C RIN = 1dBm RL = 100Ω TA = 25°C 20 0 15 3.3V Insertion Loss BW (dB) On-Resistance R ON Ω) ( 5V 10 5 5V 0 1 2 3 In p u t V o lta g e (V ) 4 -2 -3 1K 5 Figure 6. On-Resistance vs. Input Voltage -10 -10 -20 -20 Crosstalk XTALK (dB) 0 -30 -40 -50 3.3V, 5V -60 -70 -80 -30 -40 10M 100M 1G 3.3V, 5V -50 -60 -70 -80 -90 1M 10M 100M 1G Frequency (Hz) Frequency (Hz) Figure 8. Off Isolation vs. Frequency Document Number DS40562 Rev 1-2 1G PIN = 1dBm TA = 25°C RL = 100Ω 0 1M 1M 10M 100M F re q u e n c y (H z) Figure 7. Insertion Loss vs. Frequency PIN = 1dBm TA = 25°C RL = 100Ω Off Isolation OIRR (dB) 3.3V -4 0 PI5L200 -1 Figure 9. Crosstalk vs. Frequency 6 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 Part Marking Q Package W Package L Package PI5L 200QE ZYWXX Z: Die Rev Code Y: Year W: Workweek 1st X: Assembly Code 2nd X: Fab Code PI5L200 Document Number DS40562 Rev 1-2 PI5L 200WE BZYYWWXX B: Port Code Z: Die Rev YY: Year WW: Workweek 1st X: Assembly Code 2nd X: Fab Code 7 PI5L 200LE ZYWXX Z: Die Rev Y: Year W: Workweek 1st X: Assembly Code 2nd X: Fab Code www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 Packaging Mechanical: 16-QSOP (Q) 16-0056 PI5L200 Document Number DS40562 Rev 1-2 8 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 Packaging Mechanical: 16-SOIC (W) 16-0145 PI5L200 Document Number DS40562 Rev 1-2 9 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 Packaging Mechanical: 16-TSSOP (L) 16-0061 For latest package info. please check: http://www.diodes.com/design/support/packaging/pericom-packaging/packaging-mechanicals-and-thermal-characteristics/ Ordering Information Ordering Code Packaging Code Package Description PI5L200QEX Q 16-pin, 150mil Wide (QSOP) PI5L200WEX W 16-pin, 150mil Wide (SOIC) PI5L200LEX L 16-pin, 173mil Wide (TSSOP) Notes: 1. EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. All applicable RoHS exemptions applied. 2. See http://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, “Green” and Lead-free. Thermal characteristics can be found on the company web site at www.diodes.com/design/support/packaging/ 3. E = Pb-free and Green 4. X suffix = Tape/Reel PI5L200 Document Number DS40562 Rev 1-2 10 www.diodes.com January 2018 Diodes Incorporated A product Line of Diodes Incorporated PI5L200 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com PI5L200 Document Number DS40562 Rev 1-2 11 www.diodes.com January 2018 Diodes Incorporated