PI6C2401WE

PI6C2401 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Phase-Locked Loop Clock Driver Product Features Product Description • High-Performance Phase-Locked-Loop Clock Distribution for Networking, ATM, 100/134 MHz Registered DIMM Synchronous DRAM modules for server/workstation/PC applications The PI6C2401 features a low-skew, low-jitter, phase-locked loop (PLL) clock driver. By connecting the feedback CLK_OUT output to the feedback FB_IN input, the propagation delay from the CLK_IN input to any clock output will be nearly zero. • Zero Input-to-Output delay • Low jitter: Cycle-to-Cycle jitter ± 100ps max. Application • On-chip series damping resistor at clock output drivers for low noise and EMI reduction If the system designer needs more than 16 outputs with the features just described, using two or more zero-delay buffers such as PI6C2509Q, and PI6C2510Q, is likely to be impractical. The deviceto-device skew introduced can significantly reduce the performance. Pericom recommends the use of a zero-delay buffer and an eighteen output non-zero-delay buffer . As shown in Figure 1, this combination produces a zero-delay buffer with all the signal characteristics of the original zero-delay buffer, but with as many outputs as the non-zero-delay buffer part. For example, when combined with an eighteen output non-zero delay buffer, a system designer can create a seventeen-output zero-delay buffer. • Operates at 3.3V VCC • Packaged in Plastic 8-pin SOIC Package (W) Pb-free and Green Available • Wide range of Clock Frequencies Logic Block Diagram Product Pin Configuration CLK_IN CLK_OUT PLL FB_IN CLK_IN 1 AVCC 2 AGND 3 CLK_OUT 4 S Feedback Reference Clock Signal CLK_OUT FB_IN 7 VCC 6 GND 5 S Control Input 18 Output Non-Zero Delay Buffer V Zero Delay Buffer PI6C2401 8-Pin W 8 17 S Output Source PLL Shutdown 1 PLL N 0 CLK_IN Y Figure 1. This Combination Provides Zero-Delay Between the Reference Clocks Signal and 17 Outputs 08-0298 1 PS8419D 11/13/08 PI6C2401 Phase-Locked Loop Clock Driver 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Pin Functions Pin Name Pin Numbe r Type De s cription CLK_IN 1 I AVCC 2 Power Analog power supply. AGND 3 Ground Analog ground. CLK_OUT 4 O Clock outputs. The output provides low- skew copies of CLK_IN and has an embedded series- damping resistor. S 5 I Control Input S. S is used to bypass the PLL for test purposes. When S is strapped to ground, PLL is bypassed and CLK_IN is buffered directly to the device outputs. GND 6 Ground Ground. VCC 7 Power Power supply. FB_IN 8 I Reference Clock input. CLK_IN allows spread spectrum clock input. Feedback input. FBIN provides the feedback signal to the internal PLL. DC Specifications (Absolute maximum ratings over operating free-air temperature range) Symbol Parame te r VI Input voltage range VO Output voltage range M in. −0.5 M ax. Units VCC + 0.5 V VI_DC DC input voltage +5.0 IO_DC DC output current 10 0 mA Power Maximum power dissipation at TA= 55oC in still air 1.0 W TSTG Storage temperature 15 0 oC - 65 Note: Stress beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. Parame te r Te s t Conditions VCC ICC VI = VCC or GND; IO = 0(1) 3.6V CI VI = VCC or GND M in. Typ. Units 10 μA 4 3.3V CO M ax. pF VO = VCC or GND 6 Note: 1. Continuous output current 08-0298 2 PS8419D 11/13/08 PI6C2401 Phase-Locked Loop Clock Driver 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Recommended Operating Conditions Symbol Parame te r M in. M ax. 3.6 VC C Supply voltage 3.0 VIH High level input voltage 2.0 VIL Low level input voltage VI Input voltage 0 VC C TA Operating free- air temperature 0 70 Units V 0. 8 ºC Electrical Characteristics (Over recommended operating free-air temperature range Pull Up/Down Currents, VCC = 3.0V) Symbol Parame te r Condition M in. M ax. VO U T = 2.4V −12 VO U T = 2.0V −18 Pull- up current IO H Pull- down current IO L VO U T = 0.8V 18 VO U T = 0.55V 12 Units mA AC Specifications Timing Requirements (Over recommended ranges of supply voltage and operating free-air temperature) Symbol Parame te r M in. M ax. Units FCLOCK Clock frequency 25 134 MHz DCYI Input clock duty cycle 40 60 % 1 ms Stabilization Time after power up Switching Characteristics (Over recommended ranges of supply voltage and operating free-air temperature, CL=30pF) VCC= 3.3V ± 0.3V, 0-70 °C Parame te r From To tphase error without jitter CLK_IN ↑ at 100 MHz and 66 MHz FB_IN↑ M in. Typ. M ax. Units +175 ps Jitter, cycle- to- cycle At 100 MHz and 66 MHz CLK_OUT Duty cycle tr, rise- time, 0.4V to 2.0V CLK_OUT –150 +150 35 65 % 1.0 ns tf, fall- time, 2.0V to 0.4V 1.1 Note: These switching parameters are guaranteed by design. 08-0298 3 PS8419D 11/13/08 PI6C2401 Phase-Locked Loop Clock Driver 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Package Mechanical Information Plastic 8-pin SOIC Package DOCUMENT CONTROL NO. PD - 1001 8 REVISION: F DATE: 03/09/05 .149 .157 3.78 3.99 .0099 .0196 0.25 [Û 0.50 1 .189 .196 4.80 5.00 .0075 .0098 Û 0.19 0.25 0.40 .016 1.27 .050 1 .016 .026 0.406 0.660 .2284 .2440 5.80 6.20 1.35 1.75 .053 .068 SEATING PLANE REF .050 BSC 1.27 .0040 .0098 0.10 0.25 .013 0.330 .020 0.508 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Notes: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012D/AA DESCRIPTION: 8-Pin, 150-Mil Wide, SOIC PACKAGE CODE: W Ordering Information Orde ring Code Package Code Package Type Ope rating R ange PI6C2401WE W Pb- free and Green 8- pin 150- mil SO IC Commercial Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. X = Tape/Reel 3. E = Pb-free & Green Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 08-0298 4 PS8419D 11/13/08