ZXCT1030X8TA

PART OBSOLETE – CONTACT US ZXCT1030 HIGH-SIDE CURRENT MONITOR WITH COMPARATOR OBSOLETE – PART DISCONTINUED Description Pin Assignments The ZXCT1030 is a high side current sense monitor containing an internal reference and comparator with a nonlatching output. Using this device eliminates the need to disrupt the ground plane when sensing a load current. The wide input voltage range of 20V down to as low as 2.2V make it suitable for a range of applications. Dynamics and supply current are optimized for the processing of fast pulses, associated with switch mode applications. Features • • • • • • • Low cost, accurate high-side current sensing Output voltage scaling Up to 18V output 2.2V - 20V supply range Voltage reference on chip Comparator on chip SO8 package VCC VSENSEVSENSE+ GND VCOMP_OUT VOUT Vref_out VCOMP_IN Applications • • • • • • Battery chargers Electronic fuse DC motor control Over current monitor Power management Inrush current limiting Typical Application Circuit ZXCT1030 Document number: DS43711 Rev. 5 - 4 1 of 7 www.diodes.com June 2021 © Diodes Incorporated ZXCT1030 Pin Description OBSOLETE – PART DISCONTINUED Pin Name Function VCC Supply voltage VSENSE- Negative sense input VSENSE+ VREF_OUT Positive sense input Ground Comparator input, usually a ratio of the reference or other control signal Reference output VOUT Current monitor output voltage VCOMP_OUT Open collector comparator output GND VCOMP_IN Absolute Maximum Ratings Parameter Voltage on any pin Operating Temperature Storage Temperature Package Power Dissipation SO8 Rating -0.6 and VCC +0.6 -40 to 85 -55 to 125 (TAMB = 25) 700 Unit V °C °C °C mW Recommended Operating Conditions Parameter VCC VSENSE+ VSENSE (a) VOUT VCOMP_IN TAMB ZXCT1030 Min Max Units 2.2 20 V 2.2 VCC V 10 500 mV 0 VSENSE- -1V V 0.005 10 V -40 85 °C Document number: DS43711 Rev. 5 - 4 2 of 7 www.diodes.com June 2021 © Diodes Incorporated ZXCT1030 Electrical Characteristics (ZXCT1030N8) – Test conditions TAMB = 25°C, VIN = VCC = 15V, RCOMP = 10kΩ, OBSOLETE – PART DISCONTINUED VCOMP_SUPPLY = 5V unless otherwise stated. Symbol VCC VSENSE+ Parameter VOUT Output Voltage ROUT Output Resistance VOUT TC ICC ISENSE+ ISENSE- VOUT Temperature Coefficient Supply Current VCM(MIN) VSENSE+ Input Current VSENSE- Input Current (B) Minimum Active Common Mode Voltage ACC GAIN Accuracy BW Bandwidth VOUT/VSENSE COMPARATOR Input Voltage VCOMP_IN Hysteresis VH Input Bias IB Propagation Delay TD Output Voltage Low VOL VSENSE = 0 VSENSE = 10 VSENSE = 30 VSENSE = 50 VSENSE = 100 VSENSE = 500 VSENSE - = 15V, VOUT = 1V Min. 2.2 2.2 Typ. Output Sink Current IOL Output High Leakage Current IOH Voltage Reference VREF Delta VREF Change in VREF TC PSR Supply Rejection Max. 20 0 88 284 480 970 4500 2 100 300 500 1000 5000 10 112 316 520 1030 5500 mV 1.2 1.5 1.8 kΩ 30 VSENSE - = 15V VSENSE- = 14.9V VCC = 15V VCOMP_SUPPLY = 5V VCOMP_IN = VREF VSENSE = 10mV VSENSE = 100mV VSENSE = 100mV VSENSE = 10mVp-p VSENSE = 100mVp-p 170 270 48 70 ppm/°C 350 90 220 2.8 -3 9.7 10.0 0.005 30 µA µA nA V 3 10.3 3 6 5 Unit V VCC % MHz 10 15 80 100 150 150 200 V mV nA ns mV VCOMP_ Output Voltage High VOH Notes: Condition VCC Range Sense+ Range Vol = 0.4V Reference Current = +300µA to -5µA ISOURCE 5µA to ISINK 300µA SUPPLY 2 1.200 1.240 1.0 mA µA 1.280 V 10 mV 30 0.01 ppm/°C %/V (a) (VSENSE+) – (VSENSE-) (b) Level of VSENSE+ where comparator output defaults to ‘off’. ZXCT1030 Document number: DS43711 Rev. 5 - 4 3 of 7 www.diodes.com June 2021 © Diodes Incorporated ZXCT1030 OBSOLETE – PART DISCONTINUED Typical Application Circuits ZXCT1030 Document number: DS43711 Rev. 5 - 4 4 of 7 www.diodes.com June 2021 © Diodes Incorporated ZXCT1030 OBSOLETE – PART DISCONTINUED Voltage output current monitor Referring to the block diagram, the current monitor takes the small voltage developed across the sense resistor (VSENSE) and transfers it from the large common mode supply voltage to a ground referenced signal with a gain of 10. The sense input common mode range is 2.2V to 20V. In this range, a linear output voltage is delivered. Reference The bandgap reference allows the comparator to compare the translated VSENSE with threshold value chosen by the user which can be any voltage from 0 to 1.24V, configured by two external resistors which forms VCOMP_IN. The output current which can be drawn from the comparator reference (IREF source) is limited to 5μA, making potentiometers ≥250kΩ suitable for setting a threshold level. Where a lower potentiometer resistor value is used, an additional resistor value should be inserted between VREF and VCC to maintain sufficient current for the reference. (as shown in Figure 1). Figure 1: External Resistor for Reference Level The voltage reference has a maximum current sink capability. This magnitude of current will be influenced by the value of R1 which is inserted between VREF and VCC. The value of current flowing through R1 can be expressed as: I = (VCC -VREF) / R1 Comparator The open collector output is active low and is asserted when VSENSE x 10 (VOUT) > VCOMP_IN. It can be connected to any voltage rail up to VIN via a pull-up resistor. Suggest values for the resistor are in the range of 10-100kΩ. In the case where high load currents or a short circuit occurs, thus reducing the common mode signals (V+, V-) typically below 2.2V, the comparator will default to the asserted state. This can eliminate a closed loop system 'latch-up' condition, allowing the controller to remove the applied power. Stability To ensure stable operation of the ZXCT1030, it is recommended a decoupling capacitor is placed across the VCC and ground connections. A ceramic 10µF will be adequate. ZXCT1030 Document number: DS43711 Rev. 5 - 4 5 of 7 www.diodes.com June 2021 © Diodes Incorporated ZXCT1030 OBSOLETE – PART DISCONTINUED Ordering Information* Device Status(*) Package ZXCT1030X8TA ZXCT1030N8TA Obsolete Active MSOP8 SO8 Notes: Device Marking ZXCT1030 ZXCT1030 Reel Size (inches) 7 7 Tape Width (mm) 12 12 Quantity Per reel 1000 500 *ZXCT1030X8TA is obsolete for more device information please check our obsolete products search on diodes website Package Outline – SO8 ZXCT1030 Document number: DS43711 Rev. 5 - 4 6 of 7 www.diodes.com June 2021 © Diodes Incorporated ZXCT1030 OBSOLETE – PART DISCONTINUED IMPORTANT NOTICE 1. DIODES INCORPORATED AND ITS SUBSIDIARIES (“DIODES”) MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO ANY INFORMATION CONTAINED IN THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). 2. The Information contained herein is for informational purpose only and is provided only to illustrate the operation of Diodes products described herein and application examples. Diodes does not assume any liability arising out of the application or use of this document or any product described herein. This document is intended for skilled and technically trained engineering customers and users who design with Diodes products. Diodes products may be used to facilitate safety-related applications; however, in all instances customers and users are responsible for (a) selecting the appropriate Diodes products for their applications, (b) evaluating the suitability of the Diodes products for their intended applications, (c) ensuring their applications, which incorporate Diodes products, comply the applicable legal and regulatory requirements as well as safety and functional-safety related standards, and (d) ensuring they design with appropriate safeguards (including testing, validation, quality control techniques, redundancy, malfunction prevention, and appropriate treatment for aging degradation) to minimize the risks associated with their applications. 3. Diodes assumes no liability for any application-related information, support, assistance or feedback that may be provided by Diodes from time to time. Any customer or user of this document or products described herein will assume all risks and liabilities associated with such use, and will hold Diodes and all companies whose products are represented herein or on Diodes’ websites, harmless against all damages and liabilities. 4. Products described herein may be covered by one or more United States, international or foreign patents and pending patent applications. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks and trademark applications. Diodes does not convey any license under any of its intellectual property rights or the rights of any third parties (including third parties whose products and services may be described in this document or on Diodes’ website) under this document. 5. Diodes products are provided subject to Diodes’ Standard Terms and Conditions of Sale (https://www.diodes.com/about/company/terms-and-conditions/terms-and-conditions-of-sales/) or other applicable terms. This document does not alter or expand the applicable warranties provided by Diodes. Diodes does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. 6. Diodes products and technology may not be used for or incorporated into any products or systems whose manufacture, use or sale is prohibited under any applicable laws and regulations. Should customers or users use Diodes products in contravention of any applicable laws or regulations, or for any unintended or unauthorized application, customers and users will (a) be solely responsible for any damages, losses or penalties arising in connection therewith or as a result thereof, and (b) indemnify and hold Diodes and its representatives and agents harmless against any and all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim relating to any noncompliance with the applicable laws and regulations, as well as any unintended or unauthorized application. 7. While efforts have been made to ensure the information contained in this document is accurate, complete and current, it may contain technical inaccuracies, omissions and typographical errors. Diodes does not warrant that information contained in this document is error-free and Diodes is under no obligation to update or otherwise correct this information. Notwithstanding the foregoing, Diodes reserves the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes. 8. Any unauthorized copying, modification, distribution, transmission, display or other use of this document (or any portion hereof) is prohibited. Diodes assumes no responsibility for any losses incurred by the customers or users or any third parties arising from any such unauthorized use. Copyright © 2021 Diodes Incorporated www.diodes.com ZXCT1030 Document number: DS43711 Rev. 5 - 4 7 of 7 www.diodes.com June 2021 © Diodes Incorporated