ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
RoHS Compliant
• • • • •
0REB-80T12x Features
• • • • • • • Isolated High Efficiency
PRELIMINARY Rev.B
Remote On/Off Logic (Optional) Input Under Voltage Protection Output Over Voltage Protection OCP/SCP Over Temperature Protection
Fixed Frequency (400 KHz) High Power Density Low Cost
Class 1, Category 2, Isolated DC/DC Converter (refer to IPC-9592) UL60950-1 Recognized (UL/cUL) (Pending)
Applications
• • • Networking Computers and peripherals Telecommunications
Description
The 0REB-80T12x is an isolated dc/dc converter that operates from a nominal 48 Vdc source. This converter provides up to 80 W of output power. Features include remote on/off, short circuit protection, over current protection, over-temperature protection, output over-voltage protection, input under-voltage protection. These converters are provided in an industry standard eighth brick package.
Part Selection
Output Voltage 12 Vdc Input Voltage 36 Vdc - 75 Vdc Max. Output Current 6.5 A Max. Output Power 80 W Typical Efficiency 93% Model Number Active Low 0REB-80T12L Model Number Active High 0REB-80T120
Notes: Add “G” suffix at the end of the model number to indicate Tray Packaging.
Part Number Explanation 0 R EB – 80 T 12 x
12 3 4 5 67
1---Through hole mount 2---RoHS 6, change “R” to “7” means RoHS 5 3---Series name 4---Series code 5---Input range (36-75V) 6---Output voltage (12V) 7---Enable, “0” means active high, and “L” means active low
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
1
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Min -0.3 -0.3 1500 -40 -55 Typ Max 75 100 18 85 125 Unit V V V V °C °C 100mS maximum Notes
Absolute Maximum Ratings
Parameter Continuous non-operating Input Voltage Input Transient Voltage Remote On/Off I/O isolation voltage Ambient Temperature Storage Temperature
Note: Ratings used beyond the maximum ratings may cause a reliability degradation of the converter or may permanently damage the device.
Input Specifications
Parameter Operating Input Voltage Input Current (full load) Input Current (no load) Remote Off Input Current Input Reflected Ripple Current (rms) Input Reflected Ripple Current (pk-pk) I t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold
2
Min 36 33 30
Typ 48 50 10 2 10 34 31
Max 75 2.4 100 15 4 20 1 35 33
Unit V A mA mA mA mA As V V
2
Notes
With simulated source impedance of 10uH, 5Hz to 20MHz. Use a 100uF/100V electrolytic capacitor with ESR=1 ohm max, at 200KHz@25°C.
CAUTION: This converter is not internally fused. An input line fuse must be used in application. Recommend a fast-acting fuse with maximum rating of 3A on system board. Refer to the fuse manufacture’s datasheet for further information. Notes: 1. This converter has internal C-L-C (0.47uF-2.2uH-3.2uF) filter. 2. All specifications are typical at 25 °C unless otherwise stated.
Output Specifications
Parameter Output Voltage Set Point Load Regulation Line Regulation Regulation Over Temperature (-40deg.C-85deg.C) Ripple and Noise (pk-pk) Ripple and Noise (rms) Ripple and Noise (pk-pk) under worst case Min 11.76 Typ 12 0.1 0.1 30 5 Max 12.24 0.2 0.2 0.02 50 10 60 Unit V % Vo,set % Vo,set % Vo,set/C mV mV mV Vin=48V, Io=100%load at 25°C ambient, 0-20MHz BW, with a 1µF ceramic capacitor, 10uF Tantalum cap and a 220uF electrolytic cap at output. over all operating input voltage, load and ambient temperature condition Notes Vin=48V, Io=50% load Vin=48V, Io=0~100% load Vin=36~75V,Io=100% load
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
2
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Min 0 7 Typ 7.8 25 25 0 Max 6.5 8.8 0.05 15 30 30 3 5000 Unit A A As mS mS mS % uF Enable form Vin Enable form ON/OFF
2
Output Specifications (continued)
Parameter Output Current Range Output DC Current Limit Short Circuit Surge Transient Rise time Turn on Time Overshoot at Turn on Output Capacitance Transient Response △V Overshoot 50%~75% of Max Load Settling Time △V Overshoot 75%~50% of Max Load Settling Time Notes
220
Vo= 12 V -
200 350 200 350
250 450 250 450
mV uS mV uS di/dt=0.1A/us, Vin=48Vdc, Ta=25°C, with a 1µF ceramic capacitor, 10uF Tantalum cap and a 220uF electrolytic cap at output.
Note: All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
General Specifications
Parameter Efficiency Switching Frequency Output Voltage Trim Range Over Temperature Protection Over Voltage Protection(Static) Over Voltage Protection (Dynamic) Weight FIT Dimensions Inches (L × W × H) Millimeters (L × W × H) Isolation characteristics Input to Output Isolation Resistance Isolation Capacitance 1500 10M 3900 V Ohm pF 2.30 x 0.90 x 0.40 58.42 x 22.86 x 10.20 Min 90 80 13.8 Typ 93 400 110 18 TBD Max 110 120 15 18 Unit % kHz % ℃ V V g Calculated Per Bell Core SR-332 (Vin=48V, Vo=12V, Io=5A, Ta = 25 °C, 9 FIT=10 /MTBF) This voltage is achieved by trimming up output slowly. The transient over voltage is achieved by connecting the Trim pin to Vout+ pin through a 100K resistor. Notes Vin=48V, full load
Note: All specifications are typical at 25 °C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
3
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Efficiency Data
94% 92% 90% 88%
36V 48V
EFFICIENCY (%)
86% 84% 82% 80% 1.625A
75
3.25A
4.875A
6.5A
OUTPUT CURRENT (Amp)
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
4
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Min -0.3 1.8 -0.3 1.8 0 Typ Max 0.8 18 0.8 18 1 Unit V V V V mA Notes The remote on/off pin open, Unit off. The remote on/off pin open, Unit on.
Remote On/Off
Parameter Signal Low (Unit On) Signal High (Unit Off) Signal Low (Unit Off) Signal High (Unit On) Current Sink Active Low Active High
Recommended remote on/off circuit for active low
Vin+ On/off
Vin+
On/off
Vin-
Vin-
Control with open collector/drain circuit
Vin+
Vcc
Control with photocoupler circuit
Vin+
On/off
On/off
Vin-
Vin-
Control with logic circuit Recommended remote on/off circuit for active high
Vin+
Permanently on
Vin+
On/off
On/off
Vin-
Vin-
Control with open collector/drain circuit
Vin+
Vcc
Control with photocoupler circuit
Vin+
On/off
On/off
Vin-
Vin-
Control with logic circuit
Permanently on
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
5
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Output Trim Equations
Equations for calculating the trim resistor are shown below. The Trim Down resistor should be connected between the Trim pin and Sense (-) pin. The Trim Up resistor should be connected between the Trim pin and the Sense (+). Only one of the resistors should be used for any given application. Minimum trim down voltage is 9.6V Maximum trim up voltage is 13.2V. The total voltage increased by trim and remote sense should not exceed 10% of the nominal output voltage.
Vout +sense
Rtrimdown =
511 − 10.22[kΩ ] delta
Trim Rtrim_down -sense GND
Rtrimup =
(100 + delta) ⋅ Vo ⋅ 5.11 − 626 − 10.22[kΩ ] 1.225⋅ delta
Vout +sense Rtrim_up Trim -sense GND
Note:
delta =
(Vo _ req − Vo) × 100[%]
Vo
Vo_req=Desired (trimmed) output voltage [V] Output voltage Vo=12.000 V
400 Trim resistor value Rtrim_down(KOhm)
Trim resistor value,Rtrim_up(KOhm)
5000 4500 4000 3500 3000 2500 2000 1500 1000 500
360 320 280 240 200 160 120 80 40 0 9.6 9.84 10.08 10.32 10.56 10.8 11.04 11.28 11.52 11.76 Adjusted output voltage Vo,adj (V) 12
0
12
12.12 12.24 12.36 12.48 12.6 12.72 12.84 12.96 13.08 13.2 Adjusted output voltage Vo,adj(V)
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
6
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Remote Sense
This module has remote sense compensation feature. It can minimize the effects of resistance between module’s output and load in system layout and facilitates accurate voltage regulation at load terminals or other selected point. 1. The remote sense lines carries very little current and hence do not require a large cross-sectional area. 2. This module compensates for a maximum drop of 10% of the nominal output voltage. 3. If the unit is already trimmed up, the available remote sense compensation range should be correspondingly reduced. The total voltage increased by trim and remote sense should not exceed 10% of the nominal output voltage. 4. When using remote sense compensation, all the resistance, parasitic inductance and capacitance of the system are incorporated within the feedback loop of this module. It can make an effect on the module's compensation, affecting the stability and dynamic response. A 0.1uF ceramic capacitor can be connected at the point of load to de-couple noise on the sense wires. 5. Recommend the connection of remote sense compensation as below figure. There are a resistor RS+ (40.2 ohm) from Vo+ to Sense+ and a resistor RS- (40.2 ohm)) from Vo- to Sense- inside of this module.
Vo+
RS+
Sense+ Load SenseRS-
V o-
6. If not using remote sense compensation, please connect sense directly to output at module's pin, that is, connect sense+ to Vo+ and sense- to Vo- at module's pin, the shorter the better. See below figure.
V o+
RS+
Sense+ Load SenseRS-
Vo-
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
7
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Over Current Protection
To provide protection in a fault output overload condition, the module is equipped with internal current-limiting circuitry and can endure current limiting for a few mili-seconds. If the over current condition persists beyond a few milliseconds, the module will shut down into hiccup mode and restart once every 300mS. The module operates normally when the output current goes into specified range. The typical average output current is 1.75A during hiccup.
Vin=48V
Expansion of on time portion
Over Voltage Protection
The output over voltage protection consists of circuitry that monitors the voltage on the output terminals. If the voltage on the output terminals exceeds the over voltage protection threshold, the module will shutdown into hiccup mode and restart once every 300mS. The module operates normally when the fault is cleared. Test setup: Waveform: CH1: Output voltage waveform
R=100K
Vo+ K Trim R Vo-
Sense+ K Trim R Sense-
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
8
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Over Temperature Protection
The OTP is achieved by thermistor R67 and the threshold is set at 110C in non-latch mode; the hottest component Q3 reaches 112C with 100LFM air flow correspondingly. It will restart automatically when the temperature falls down to 105C. The protecting point will be varied a little under different conditions (air flow, ambient temperature, input voltage, load...).
Input Under-voltage Lockout
Input Current
Under-voltage Lockout
Voltage Falling
V1=31V V2=34V
Voltage Rising
V1
V2
Input Voltage (V)
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
9
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Ripple and Noise Waveform
48Vdc input, 12Vdc/6.5A output Note: Ripple and noise at full load, with a 1uF ceramic cap and a 10 uF Tantalum cap and a 220uF electrolytic cap at output, Ta=25 deg C.
Transient Response Waveforms
Vout= 12V 50%-75% Load Transients
Vout= 12V 75%-50% Load Transients
Note: Transient Response at Vin=48V, di/dt=0.1A/uS, with a 1uF ceramic cap and a 10uF aluminum cap and a 220uF electrolytic cap at the output.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
10
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Startup & Shutdown
Rise Time
Vin=48V, Vo=12V, Io=6.5A
Startup time
Startup from Vin Ch1: Vo Ch3: Vin Vin=48V, Vo=12V, Io=6.5A
Startup from on/off Ch1: Vo Ch3: on/off Vin=48V, Vo=12V, Io=6.5A
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
11
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Startup & Shutdown (continued)
Shutdown
Vin=48V, Vo=12V, Io=6.5A
Thermal Derating Curve
Maximum junction temperature of semiconductors derated to 120 degree C.
Derating curve under normal input
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
12
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Thermal Derating Curve (continued)
Temperature reference points on top side
Temperature reference points on bottom side
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
13
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Safety & EMC
Safety 1. Material flammability 2. TUV Certification 3. UL Certification EMC 1. Surge IEC61000-4-5 2. DC-DIP IEC61000-4-29 3. Conductive EMI EN55022 class A Compliance to EN55022 class A (both q.peak and average) with the following inductive and capacitive filter Setup: UL94V-0 EN60950-1 UL60950-1
C4 + Vin C1 -V in T1 C5 T1 C onv.positive input C2 C3 Conv.negative input
Item 1 2 3 4 5 6
Designator C1 C2 C3 C4 C5 T1
Parameter 1uF/100V,ceramic 0.1uF/100V, ceramic 100uF/100V, AL cap 22nF/1000V,ceramic 22nF/1000V,ceramic 1.3mH, common mode
Vendor Murata TDK Nichicon Johanson Johanson Pulse
Vendor P/N GRM32ER72A105KA01L C3216X7R2A104K UVZ2A101MPD 631S41W223KV4E 631S41W223KV4E P0402NL
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
14
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Layout
Layout of components on top side
Layout of components on bottom side
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
15
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Mechanical Outline
.
Pin 1 2 3 4 5 6 7 8
Function Vin(+) RC Vin(-) Vout(-) RSTRIM RS+ Vout(+)
Dia. 0.04’’ 0.04’’ 0.04’’ 0.062’’ 0.04’’ 0.04’’ 0.04’’ 0.062’’
Note: 1. Pin 5 must be connected to Vout(-) 2. Pin 7 must be connected to Vout(+)
Note: This module is recommended and compatible with Pb-Free Wave Soldering and must be soldered using a peak solder temperature of no more than 260 ºC for less than 5 seconds. Note: 1) All Pins: Material - Copper Alloy; Finish – 3 micro inches minimum Gold over 50 micro inches minimum Nickel plate. 2) Undimensioned components are shown for visual reference only. 3) All dimensions in inches (mm); Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm).
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
16
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/6.5 A Output Nov. 15, 2010
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Revision History
Date 2010-09-11
Revision PA First release
Changes Detail
Approval XF Jiang
1. Updated Turn-on/off voltage threshold in Input specifications. 2010-11-15 PB 2. Updated Load regulation, Line regulation, Output ripple and noise, Output DC current limit, Turn on time, Output capacitance, Transient response in Output specifications 3. Updated Remote on/off. XF Jiang
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products.
©2010 Bel Fuse Inc. Specifications subject to change without notice. 111510
17
CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com