ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
RoHS Compliant
0RQ1-Q0T12x Features
Isolated High Efficiency
PRELIMINARY Rev.A
Input Under-voltage Protection Output Over-voltage Protection OCP/SCP Over Temperature Protection Remote ON/OFF
Fixed Frequency (300 KHz) High Power Density Low Cost
Class 2, Category 2, Isolated DC/DC Converter (refer to IPC-9592)
Applications
Networking Computers and peripherals Telecommunications
Description
The 0RQ1-Q0T12x is an isolated dc/dc converter that operates from a nominal 48 Vdc source. This converter is intended to provide isolation and step down to generate a regulated intermediate bus for the purpose of powering non-isolated Point-of-Load (POL) converters. This unit will provide up to 400 W of output power from a nominal 48 Vdc input.
Part Selection
Output Voltage 12 Vdc Input Voltage 36 Vdc - 75 Vdc Max. Output Current 33 A Max. Output Power 400 W Typical Efficiency 95.5% Model Number Active Low 0RQ1-Q0T12L Model Number Active High 0RQ1-Q0T120
Notes: Add “G” suffix at the end of the model number to indicate Tray Packaging.
Part Number Explanation 0 R Q1 – Q0 T 12 x
12 3 4 5 67
1---Through hole mount 2---RoHS 6, change “R” to “7” means RoHS 5 3---Series name 4---Series code 5---Input range (36-75V) 6---Output voltage (12V) 7---Option, “x” of the model part number to be 0-9, A-Z, which will represent the special request of customer.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
1
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Min -0.3 -0.3 -40 -55 Typ Max 100 10 85 125 Unit V V C C Notes
Absolute Maximum Ratings
Parameter Continuous non-operating Input Voltage Remote On/Off Ambient Temperature Storage Temperature
Note: Ratings used beyond the maximum ratings may cause a reliability degradation of the converter or may permanently damage the device.
Input Specifications
Parameter Operating Input Voltage Input Current (full load) Input Current (no load) Remote Off Input Current Input Reflected Ripple Current (rms) Input Reflected Ripple Current (pk-pk) I2t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold Min 36 34 32 Typ 48 140 4 50 80 35 34 Max 75 12 200 8 1 36 34.8 Unit V A mA mA mA mA A2s V V 12μH source impedance; VIN= 48V,Io= Iomax Notes
CAUTION: This converter is not internally fused. An input line fuse must be used in a pplication. Recommend a fast-acting fuse with maximum rating of 20A on system board. Refer to the fuse manufacture’s datasheet for further information. Note: All specifications are typical at 25 C unless otherwise stated.
Output Specifications
Parameter Output Voltage Set Point Load Regulation Line Regulation Output Ripple and Noise (pk-pk) Output Ripple and Noise (rms) Ripple and Noise (pk-pk) under worst case Output Current Range Output DC Current Limit Rise time Min 11.8 11 -30 0 Typ 12 20 100 10 40 Max 12.2 30 30 150 20 200 33 15 Unit V V mV mV mV mV mV A A mS Vin≤40V, TBD Vin=48V, Io=0~100% load Vin=40~75V,Io=100% load 0-20MHz BW, with a 1µF ceramic capacitor and a 10uF tantalum at output. Over all operating input voltage, load and ambient temperature condition. Notes Vin>40V, Io=50% load
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
2
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Parameter Min Typ 30 30 0 Max 35 35 3 5000 Unit mS mS % uF Notes Enable from Vin Enable from ON/OFF
Output Specifications (continued)
Turn on Time Overshoot at Turn on Output Capacitance Transient Response △V Overshoot 50%~75% of Max Load Settling Time
△V 75%~50% of Max Load
0
Vo= 12 V -
300 500 300 500
-
mV uS mV uS di/dt=0.1A/us, Vin=48Vdc, Ta=25°C, Tested with a 1.0μF ceramic, a 10μF tantalum, and 470μF capacitor and across the load.).
Overshoot Settling Time
Note: All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
General Specifications
Parameter Efficiency Switching Frequency Over Temperature Protection Over Voltage Protection Weight FIT Dimensions Inches (L × W × H) Millimeters (L × W × H) Isolation characteristics Input to Output Isolation Resistance Isolation Capacitance 1500 10M 2700 V Ohm pF 2.28 x 1.45 x 0.50 57.91 x 36.83 x 12.70 Min 280 Typ 95.5 300 125 TBD TBD Max 320 14 Unit % kHz ℃ V g Calculated Per Bell Core SR-332 (Vin=48 V, Vo=12 V, Io=33 A, Ta = 9 25°C, FIT=10 /MTBF) Notes Vin=48V, full load
Note: All specifications are typical at 25 C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
3
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Efficiency Data
98.00% 96.00% 94.00% 92.00% 90.00% 88.00% 86.00% 84.00% 82.00% 80.00% 8.00 15.00 25.00 33.00 OUTPUT CURRENT(A)
36 V 48 V 75 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
4
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Remote On/Off
Parameter Signal Low (Unit On) Signal High (Unit Off) Signal Low (Unit Off) Signal High (Unit On) Current Sink Active Low Active High Min -0.3 2.4 -0.3 2.4 0 Typ Max 0.8 10 0.8 10 0.3 Unit V V V V mA Notes 0RQ1-Q0T12L The remote on/off pin open, Unit off. 0RQ1-Q0T120 The remote on/off pin open, Unit on.
Recommended remote on/off circuit for active low
Vin+
Vin+
On/off
On/off
Vin-
Vin-
Control with open collector/drain circuit
Vin +
Vcc
Control with photocoupler circuit
Vin+
On/off
On/off
Vin -
Vin-
Control with logic circuit Recommended remote on/off circuit for active high
Vin+
Permanently on
Vin+
On/off
On/off
Vin-
Vin-
Control with open collector/drain circuit
Vin +
Vcc
Control with photocoupler circuit
Vin+
On/off
On/off
Vin -
Vin-
Control with logic circuit
Permanently on
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
5
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Over Current Protection
To provide protection in a fault output overload condition, the module is equipped with internal current -limiting circuitry and can endure current limiting for a few mili-seconds. If the over current condition persists beyond a few milliseconds, the module will shut down into hiccup mode and restart once every 400mS. The module operates normally when the output current goes into specified range. The typical average output current is 3.2A during hiccup.
CH1: Output Voltage CH2: Output current waveform Test condition: Vin=48V
CH1: Output Voltage CH2: Output current waveform Expansion of on time portion of above figure
Ripple and Noise Waveform
48Vdc input, 12Vdc/33A output Note: Ripple and noise at full load, 0-20MHz BW, with a 1uF ceramic cap and a 10 uF Tantalum cap at output, Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
6
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Input Under-voltage Lockout
Under- voltage Lockout
Voltage Falling
V1=35V V2=34V
Voltage Rising
V1
V2
Input Voltage ( V)
Transient Response Waveforms
Vin= 48V 50%-75% Load Transients
Vin= 48V 75%-50% Load Transients
Note: Transient Response at di/dt=0.1A/uS, Vin=48Vdc, Ta=25°C, Tested with a 1.0μF ceramic, a 10μF tantalum, and 470μF capacitor and across the load.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
7
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Startup & Shutdown
Turn on rise time
Vin=48V, Vo=12V, Io=33A
Turn on delay time
Startup from Vin Ch1: Vo Ch2: Vin Vin=48V, Vo=12V, Io=33A
Startup from on/off Ch1: Vo Ch2: on/off Vin=48V, Vo=12V, Io=33A
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
8
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Startup & Shutdown (continued)
Shutdown
Vin=48V, Vo=12V, Io=33A
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
9
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Thermal Derating Curve
Maximum junction temperature of semiconductors derated to 120 degree C.
T.B.D.
AIR FLOW Bottom view
Derating curve under 55V input The OTP is achieved by temperature sensor U10 and it's in non-latch mode when the hottest component Q6 reaches 125°C with 200LFM air flow correspondingly. It will restart automatically when the temperature falls down to 105°C. The protecting point will be varied a little under different conditions (air flow, ambient temperature, input voltage, load...).
Temperature reference points on top side
Temperature reference points on bottom side
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
10
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Safety & EMC
Safety 1. Material flammability 2. UL Certification EMC Conductive EMI EN55022 class A Compliance to EN55022 class A (both q.peak and average) with the following inductive and capacitive filter Setup: UL94V-0 UL60950-1
C Y12
C Y22
C Y32
C Y42
R Y22 R Y12
R Y32
R Y42
+Vin C X1 -Vin
+Vout T2 A C X3 C X4 -Vou t
3 1 R Y11 C Y11
4 T1 A C X2 2 R Y21 C Y21
3 1
4
Test m odule
2 R Y31 R Y41 C Y31 C Y41
Item 1 2 3 4 5 6 7 8 9 10 11 12
Designator CX2 CX3 CY31 CY32 CY41 CY42 RY31 RY32 RY41 RY42 T2A T1A,CX1,CX2 RY11,RY21,RY12 RY22,CY11,CY21 CY12,CY22
Parameter 220uF/100V, AL cap 330uF/100V, AL cap 2*6.8nF/1000V,ceramic 2*6.8nF/1000V,ceramic 6.8nF/1000V,ceramic 6.8nF/1000V,ceramic 1206,0R,Resistor 1206,0R,Resistor 1206,0R,Resistor 1206,0R,Resistor 0.81mH, common mode NIL
Vendor
Vendor P/N
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
11
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Safety & EMC (continued)
Positive Line
Negative Line
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
12
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Mechanical Outline
Pin 1 2 3 4 5
Function Vin(+) Enable Vin(-) Vout(-) Vout(+)
Dia. 0.04’’ 0.04’’ 0.04’’ 0.06’’ 0.06’’
Length 0.145’’ 0.145’’ 0.145’’ 0.145’’ 0.145’’
Note: This module is recommended and compatible with Pb-Free Wave Soldering and must be soldered using a peak solder temperature of no more than 260 ºC for less than 5 seconds. Note: 1) All Pins: Material - Copper Alloy; Finish – 3 micro inches minimum Gold over 50 micro inches minimum Nickel plate. 2) Undimensioned components are shown for visual reference only. 3) All dimensions in inches (mm); Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm).
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
13
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/33 A Output May 23, 2011
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Revision History
Date 2011-05-23
Revision PA First release
Changes Detail
Approval YF Sun
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products.
2011 Bel Fuse Inc. Specifications subject to change without notice. 052311
14
CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com