79202-B

POWERLINE SIGNAL COUPLERS 3 and 4 Winding Boxed and Sleeved Variants FEATURES • • • • • Designed for use with Intellon INT5131/INT1000 and INT51X1 chipsets Fully compatible with Bel’s 79102 family of products Variants available for desktop, DC wallplug and AC power corded implementations Provides reinforced isolation for world wide application Minimum footprint design Part Number 79201 79201-B 79202 79202-B Description Three winding coupler with sleeve and wire leads Three winding coupler in rigid pinned box Four winding coupler with sleeve and wire leads Four winding coupler in rigid pinned box BENEFITS Bel’s 79201 and 79202 are signal coupling transformers for use with the full range of Intellon HomePlug™ 1.0 compliant chipsets. These transformers provide a low cost high quality solution to simplify the implementation of HomePlug products. The couplers are fully compatible with APC79101-x analog front end modules for maximum design flexibility, as well as the latest 79102xx-x modules incorporating the INT51X1 chipset for more highly integrated systems. A single 79201 coupler may be used where the chipset is co-located with the equipment power supply such as a mains powered desktop unit or wallplug modem. With the addition of a 79202 coupler, the chipset may be located in equipment fed from a DC line cord wall adapter. I n Partnership with ©2003 Bel Fuse Inc. Specifications subject to change without notice. 11.11.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 POWERLINE SIGNAL COUPLERS 3 and 4 Winding Boxed and Sleeved Variants TYPICAL APPLICATIONS D esktop product with an AC power cord 200k 200k ��� ��� �� ����� � � � � �� ������ �� ������ � ����������� �� �������� � � ����� ���� ���� ����� ��� ��� ��������������� S elf contained wall plug product ���� ���� ��� ��� �� ����� �� ������ � � � � �� ������ � ����������� �� ��������� � ����� ��� ��� ���� ���� ������� ©2003 Bel Fuse Inc. Specifications subject to change without notice. 11.11.03 page 2 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com POWERLINE SIGNAL COUPLERS 3 and 4 Winding Boxed and Sleeved Variants TYPICAL APPLICATIONS D esktop product with a DC power cord �� �� �� �� �� Notes 1. A suitable MOV transient suppressor should be chosen depending on the designed AC supply voltage of the product. We recommend a 240V part for 115VAC operation or a 375V part for 230-250V application. 2. High frequency isolation may be required if power supply circuits with high input capacitance, such as switch mode designs, are used. Inductors for this purpose should be minimum 25uH and have good performance in the 4 to 21 MHz band. M ECHANICAL 79201 0.531 [13.50] max 0.276 [7.00] max Note: Dashed box defines maximum component outline. Recommended hole size ø0.03 [0.75] 0.200 [5.08] Pitch in 2 places 0.571 [14.50] max 0.200 [5.08] 1 0.100 [2.54] Pitch in 2 places 0.197 [5.00] ©2003 Bel Fuse Inc. Specifications subject to change without notice. 11.11.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 3 POWERLINE SIGNAL COUPLERS 3 and 4 Winding Boxed and Sleeved Variants MECHANICAL 79201-B �������� ����� ������� ����� ������ ��������� �������� ���������������������� ������������ �������� ����� ������� ����� ������� ������������ ����� ������������ �������� ����� ������ ���������������� ������� ����� ������ ������������ 79202 0.531 [13.50] max 0.276 [7.00] max Note: Dashed box defines maximum component outline. Recommended hole size ø0.03 [0.75] 0.100 [2.54] Pitch in 4 places 0.571 [14.50] max 0.200 [5.08] 1 0.197 [5.00] ©2003 Bel Fuse Inc. Specifications subject to change without notice. 11.11.03 0.150 [3.81] Pitch in 2 places page 4 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com POWERLINE SIGNAL COUPLERS 3 and 4 Winding Boxed and Sleeved Variants MECHANICAL 79202-B Top View 0.551 [14.00] 0.354 [9.00] Side View End View Recommended PCB Layout 0.100 [2.54] 4 places 0.591 [15.00] 0.516 [13.10] Pin 1 0.300 [7.62] 0.200 [5.08] 2 places 0.138 [3.50] Pins 3 & 8 removed 0.195 [4.95] 0.020 [0.50] ©2003 Bel Fuse Inc. Specifications subject to change without notice. 11.11.03 Intellon, PowerPacket, SIMPLE and SIMPLE PowerBus are registered trademarks of Intellon Corportation. CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Stewart Connector 45/46 Riverside Medway City Estate Rochester, Kent ME2 4DP U.K. Tel 44-1634-722890 Fax 44-1634-716677 www.belfuse.com page 5