A447-0070-10

defining a degree of excellence 10 TAP LEADING EDGE CONTROL STANDARD DELAY MODULES .60 + .01 13 .375 .350 12 3 Vcc 14 In 1 Gnd 7 Cat 11-R5 .60 + .01 .325 bel (DC) (P/N) .285 Max 11 10 9 4 5 6 8 bel * (DC) (P/N) .285 Max .10 Typ .80 Max .22 Max .018 Coplanarity + .002 .10 Typ .80 Max .015 .004 4o .012 .008 .012 .008 .23 Max 100o 90o .20 Max .015 Min .045 .030 .12 Min .018 Part Numbers SMD S422-0025-10 S422-0030-10 S422-0040-10 S422-0050-10 S422-0060-10 S422-0070-10 S422-0080-10 S422-0090-10 S422-0100-10 S422-0125-10 S422-0150-10 S422-0200-10 S422-0250-10 Total Delay Delay per Tap A447-0025-10 * 22.5 ns 2.5 + 1 ns A447-0030-10 * 27 ns 3 + 1.5 ns A447-0040-10 * 36 ns 4 + 1.5 ns Thru-Hole A447-0050-10 A447-0060-10 A447-0070-10 A447-0080-10 A447-0090-10 A447-0100-10 A447-0125-10 A447-0150-10 A447-0200-10 A447-0250-10 50 ns 60 ns 70 80 90 100 125 150 200 250 ns ns ns ns ns ns ns ns Rise Time 3 ns Ein Trin PW PP Iccl Vcc Test Conditions @ 25oC Pulse Voltage Rise Time Pulse Width Pulse Period Supply Current Supply Voltage 3.2 Volts 3.0 ns (10%-90%) 1.2 x Total Delay 4 x Pulse Width 80 ma Typical 5.0 Volts 3 ns 3 ns 5 ns 3 ns 6 ns 3 ns ns ns ns ns ns ns ns ns 3 3 3 3 3 3 3 3 ns ns ns ns ns ns ns ns Electrical Characteristics Vcc Vih Vil Ioh Iol Voh Vol Vik Iih Iil Ios Icch Iccl Ta PW d Tc Supply Voltage Logic 1 Input Voltage Logic 0 Input Voltage Logic 1 Output Current Logic 0 Output Current Logic 1 Output Voltage Logic 0 Output voltage Input Clamp Voltage Logic 1 Input Current Logic 0 Input Current Short Circuit Output Current Logic 1 Supply Current Logic 0 Supply Current Operating Free Air Temperature Min. Input Pulse Width of Total Delay Maximum Duty Cycle Min. 4.75 2.0 Max. 5.25 0.8 -1 20 2.7 0.5 -1.2 40 -1.2 -150 50 90 70o 50 Units V V V ma ma V V V ua ma ma ma ma C % % 7 8 9 10 12.5 15 20 25 Tolerances Input to Taps + 2 ns or 5% , Whichever is Greater Tap to Tap + 2 ns or 7% , Whichever is Greater Delays measured @ 1.5 V levels on Leading Edge only with no loads on Taps Rise and Fall Times measured from 0.75 V to 2.4 V levels * Ref. Delay from P13, Delay P1-P13 = 4.5 ns typical -60 0o 40 Drive Capabilities Nh Logic 1 Fanout Nl Logic 0 Fanout 20 TTL Loads Max. 10 TTL Loads Max. Temp. Coeff. of Total Delay (TD) 100 + (25000/TD) PPM/OC Notes Transfer molded for better reliability Compatible with TTL & DTL circuits Terminals: Electro-Tin plate phosphor bronze Performance warranty is limited to specified parameters listed SMD - Tape & Reel available: 32mm Wide x 16mm Pitch, 500 pieces per 13" reel Recommended Temperature Profile 300o C 200o C 100o C Temp. Infra Red 225o C Max Temp. > 185o C for 90 Seconds Max 0 2 4 6 Ti m e i n M i n u t e s 8 Other Delays and Tolerances Available Consult Sales Specifications subject to change without notice. Corporate Office Bel Fuse Inc. 198 Van Vorst Street, Jersey City, NJ 07302-4496 Tel: 201-432-0463 Fax: 201-432-9542 E-Mail: BelFuse@belfuse.com Internet: http://www.belfuse.com Far East Office Bel Fuse Ltd. 8F/8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel: 852-2328-5515 Fax: 852-2352-3706 European Office Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Preston PR1 8UD Lancashire, U.K. Tel: 44-1772-556601 Fax: 44-1772-888366 13