ABC225-1T24L

The ABC225 Series of open-frame power supplies, with its wide universal 90-264 VAC input range and high power density, is available at 225 W of output power and a variety of single and multiple output voltages. The high efficiency and high power density of the ABC family ensures minimal power loss in end-use equipment, thereby facilitating higher reliability, easier thermal management and meets regulatory approvals for environmentally-friendly end products. These power supplies are ideal for telecom, datacom, industrial equipment and other applications. • 2 x 4 x 1 Inches Form Factor • 225 W with Forced Air Cooling • Efficiencies up to 94% • -40 to 70 °C Operating Temperature • 12 V Fan Output, Thermal Shut-Down Feature • 3.37 Million Hours, Telcordia - SR332-Issue 3 MTBF • Standby Power 110% Over Voltage Protection Short Circuit Protection 110 to 140% Hiccup mode Conducted Emissions EN55032-B, CISPR22-B, FCC PART15-B Pass Radiated Emissions EN 55032 A; with external core (King core K5B RC 25x12x15-M in input cable) Pass Level B Input Current Harmonics EN 61000-3-2 Class D Voltage Fluctuation and Flicker EN 61000-3-3 Pass ESD Immunity EN 61000-4-2 Level 3, Criterion A Radiated Field Immunity EN 61000-4-3 Level 3, Criterion A Electrical Fast Transient Immunity EN 61000-4-4 Level 3, Criterion A Surge Immunity EN 61000-4-5 Level 3, Criterion A Conducted Immunity EN 61000-4-6 Level 3, Criterion A Magnetic Field Immunity EN 61000-4-8 Level 3, Criterion A Voltage Dips, Interruptions EN 61000-4-11 Criterion A & B PARAMETER DESCRIPTION / CONDITION SPECIFICATION Isolation Voltage Input to Output: (For ITE application) Input to GND: (Not Applicable For Class II Option) 3000 VAC 1500 VAC Safety Standard(s) Approved to the latest edition of the following standards: CSA/UL60950-1, EN60950-1 and IEC60950-1; Class1 SELV. Agency Approvals Nemko, UL, C-UL CE mark Complies with LVD Directive 4 Combined output power of main output, fan supply shall not exceed max. Power rating. Fan supply output voltage tolerance including set point accuracy, line & load regulation is +/-10% and Ripple & noise is less than 10%. 6 Adjustment potentiometer is located on the SMT side of the PCB. 5 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2017 Bel Power Solutions & Protection BCD.00554_AG Asia-Pacific +86 755 298 85888 ABC225 Series 4 PARAMETER Operating Temperature7 DESCRIPTION / CONDITION SPECIFICATION Start-up is guaranteed, with spec deviation, see Fig. 1 -40 to +70°C -40 to 0°C Storage Temperature -40 to +85°C Cooling With 13 CFM forced air cooling With natural convection cooling at 100 to 264 VAC 225 W Up to 120 W Relative Humidity Noncondensing 5% to 95% Altitude Operating: Nonoperating: 16,000 ft. 40,000 ft. Reliability MTBF according to Telcordia -SR332-issue 3: 3.37 million hours Convection load: 120 W up to 40 °C De-rate between 40-50 °C @ 0.625% per °C De-rate above 50 °C @ 2.33% per °C Forced air cooled load: 225 W up to 50°C De-rate above 50 °C @ 2.5% per °C Figure 1. Derating Curve Figure 2. Efficiency Graph at 115 VAC 7 Figure 3. Efficiency Graph at 230 VAC Output ripple can be more than 10% of the output voltage. tech.support@psbel.com ABC225 Series CONNECTOR PIN 5 DESCRIPTION/CONDITION MANUFACTURER / PN AC Line Not Fitted AC Neutral Molex: 26-60-4030 Mating: 09-50-3031; Pins: 08-50-0106 AC Input Connector J1 Pin 1 Pin 2 Pin 3 DC Output Connector J2 Pin 1,2,3 Pin 4,5,6 V1 +VE V1 - VE Pin 1 Pin 2 FAN +VE FAN - VE Aux (Fan) Output J3 Screw Terminal (Option 1) Molex Connector (Option 2) Molex: 39357 Series or equivalent Molex: 26-60-4060 Mating: 09-50-3061; Pins: 08-50-0106 AMP :640456-2 Mating: 640440-2 PARAMETER DESCRIPTION/CONDITION Weight 200 g approx. Dimensions 50.8 x 101.6 x 25.4 mm (2 x 4 x 1 inch) Cooling8 225 W with 13 CFM forced air cooling (refer Mechanical Drawing) Up to 120 W with natural convection cooling (refer Derating Curve) Figure 4. Mechanical Drawing – Screw Terminal (Option 1) 8 225 W with 13CFM forced air cooling and 120 W with natural convection cooling at 100 to 264 VAC. Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2017 Bel Power Solutions & Protection BCD.00554_AG Asia-Pacific +86 755 298 85888 6 ABC225 Series Figure 5. Mechanical Drawing – Molex Connector (Option 2) NOTES: In case the PCB is mounted in a metal enclosure, using metal hardware ensure the following: 1 Stand off, used to mount PCB has OD of 5.4 mm max. 2 Screws, used to fix PCB on stand off, have head dia of 6.0 mm max. 3 Washer, if used, to have dia of 6.5 mm max. NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. tech.support@psbel.com