The FXP7000 Series of rack-mounted power
systems provides AC front-end capability to
automatic test equipment, telecom, data
communications, and other distributed power
designs. The hot-pluggable FXP supplies do
not include an output isolation diode and may
be paralleled up to 210 kW of total output
power. These supplies provide excellent
protection against input voltage transients.
Three-Phase AC Input
Suitable for 3U or 5U Height Mounting
Single-Wire Current Share or Droop Current Share
Remote Voltage Adjust and Current Monitoring
Overtemperature, Overload and Overvoltage
Protection
LED Supply Status Indicators
Current Share Control for up to 30 Units
Standard & Customized Rack Adaptors Available
Front Panel Selectable-Input-Range
RoHS Compliant
Access to interfaces for remote sensing,
remote voltage adjust, current sharing, current
monitoring, power supply status, standby
voltage and inhibit, as well as power
connections, is through a connector at the rear
of the supply. The FXP has its fan, handles,
voltage adjust, and indicator lights on the front
panel and a single hot-plug connector on the
rear. Airflow is from the front through the rear.
Alarm, monitoring, and control signals are
floating from the main output and can be
referenced to the positive or negative output
or sense line of the power supply. The output
is floating with respect to the chassis and may
be used as a positive or negative polarity
supply.
The FXP7000 Series meets international safety
requirements and is CE Marked to the Low
Voltage Directive. This series operates on
three-phase European voltages as well as (up
to) 480 VAC, delta or wye.
North America
+1.866.513.2839
Asia-Pacific
+86.755.29885888
Europe, Middle East
+353.61.225.977
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00275_AB
FXP7000 Series
MODEL
OUTPUT
VOLTAGE
INPUT VOLTAGE
RANGE
3-PHASE
ADJUSTMENT
RANGE
MAXIMUM
OUTPUT
CURRENT
LINE
REGULATION
LOAD
REGULATION 1
INITIAL SETTING
ACCURACY
FXP7000-48-SG
48 V
180 to 264 VAC or
342 to 528 VAC
45.6 V to 50.4 V
145 A
0.15%
0.2%
47.90 V to 48.10 V
PARAMETER
Input Voltage - AC
Input Current
Inrush Surge Current 2
Input Frequency
Hold-up Time
Operating Frequency
DESCRIPTION/CONDITIONS
3-phase delta low input range, nominal.
3-phase delta high input range, nominal.
Continuous deviation from the above nominals.
Per phase at full rated load.
FXP7000 at 180 VAC:
Internally limited.
Vin = 264 VAC (one cycle). 25° C:
Vin = 528 VAC (one cycle). 25° C:
AC input.
After last AC line peak at full power.
208 VAC:
400 VAC:
Switching frequency, fixed.
Power Factor
Continuous duty rating.
Efficiency
Full rated load (208 VAC).
Load, Maximum deviation with 0 to 100% load change:
With Remote Sense connected:
With Remote Sense not connected:
Utilizing Droop Current Share:
Line, Under all specified operating conditions.
Measured at mating connector w/ 0.01μF + 10μF Tant. 20 MHz BW:
100 MHz BW:
Output voltage overshoot/undershoot at turn-on.
88
0
Turn-On Delay
Minimum loading required to maintain regulation.
Max. recovery time, to within 1% of initial set point due to a 25% load
change, 1A/μs.
Time:
Deviation:
Time required for initial output voltage stabilization after power-up.
Turn-on Rise Time
Time required for output voltage to rise from 10% to 90%.
Minimum Loads
Transient Response
2
UNITS
VAC
VAC
%
Arms
Apk
Hz
ms
100
Output Current
Overshoot / Undershoot
MAX
240
480
+10
30
38
38
63
kHz
0.90
DESCRIPTION/CONDITIONS
An additional 1.0 Volt is provided to the output terminals to provide for
load lead losses.
Continuous duty rating.
Ripple & Noise
NOM
47
17
13
PARAMETER
Output Voltage
Adjustment Range
Output Power
Regulation
1
MIN
200
380
-10
W/VA
MIN
NOM
MAX
UNITS
45.6
48
50.4
7000
V
Watts
145
A
91
%
0.2
0.75
2.0
0.2
1
2
0
%
% p-p
%
A
800
3.2
3
μs
%
s
100
ms
With Remote Sense connected.
The minimum time OFF between two turns ON of the unit needs to be > 30 seconds
+1.866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00275_AB
FXP7000 Series
PARAMETER
3, 4
AC Power Fail Warning
DESCRIPTION/CONDITIONS
MIN
NOM
MAX
UNITS
Input Range Select Status
Warning provided prior to Vout dropping 5% after loss of AC input.
Output voltage - diode isolated. Inclusive of line, load, and initial
tolerances.
Output current.
Monitor output current over a compliance range of 0~10 V.
Normal output:
Total error current:
Static sharing deviation as a percent of full-load rating for loads
>10%.
Active:
Passive:
Maximum signal resistance in high input voltage range selection.
Loss of Phase Warning
Warning provided prior to protective reduction in current limit.
Output Inhibit 5
Voltage required to enable supply (0.5 mA sink).
1.0
V
Output Interlock 5
Voltage required to enable supply (6 mA sink).
1.0
V
Output Overload Protection
Straight line current limit (above approx. 5 V Vout).
149
156
A
Output Overload Warning
2.2
Output Voltage Fault Signal
Signal level on overload.
Occurs on overload when Vout is below approx. 5 V.
May operate in burst-mode.
Deviation from adjusted Vout that is considered as a fault.
Output Voltage Margin
Overtemperature /
Fan Failure Warning
Overvoltage Protection
Output voltage swing available through Margin pin (analog).
Time between fault warning and shutdown.
Latching shutdown.
Latch style overvoltage protection.
Power Supply Present Signal
Resistance to logic ground upon insertion of supply.
Remote Sense
Maximum load lead loss compensation (round trip).
PARAMETER
ESD Susceptibility
DESCRIPTION / CONDITIONS
Approved to the latest edition of the following standards:
UL/CSA60950-1, IEC60950-1 and EN60950-1.
CE marked for the Low Voltage Directive.
FCC CFR title 47 Part 15 Sub-Part B - Conducted.
EN55022 / CISPR 22 Conducted.
Per EN61000-4-2, level 4
Radiated Susceptibility
Per EN61000-4-3, level 3.
EFT/Burst
Per EN61000-4-4, level 4.
Per EN61000-4-5.
Auxiliary Power
Current Monitor
Current Share
Output Short Circuit Protection
Agency Approvals
Electromagnetic Interference
Input Transient Protection
Voltage Sag Immunity
Leakage Current
Per SEMI F47-0200 FXC/FXP7000
Per UL60950 and EN60950:
4
11.6
0.5
ms
12.0
12.4
V
500
mA
0.5
mA/A
mA
0.10
0
5
10
%
Ω
0.10
500
Iavg:
Line-to-Line:
Line-to-Ground:
25
±3
ms
V
±4
90
±5
A
%
±4.8
100
±5.0
±5.2
%
ms
55.2
57.6
60.0
V
Ω
1000
1.0
MIN
NOM
MAX
A
A
8
V
UNITS
Class
kV
10
V/M
±4
4
3
kV
kV
Pending
FXP7000 at 240 VAC, 60 Hz:
FXP7000 at 400 VAC, 50 Hz:
FXP7000 at 480 VAC, 60 Hz:
5
7
10
mA
3
All logic outputs listed below feature a standard active pull-down output with 0.4V max at 40mA sink capability, and a 100k pull-up to 5V.
In addition to those listed below, signals and front-panel LEDs are provided to indicate: overtemperature / fan fault, AC phase imbalance,
output good, interlock open, and supply inhibited. The FXP also provides 4 LED’s indicating output loading.
5
Both signals must be pulled to logic ground for the unit to operate.
Enables are 100% redundant internally for applications where redundant inhibit is desirable. Contact factory for additional design details.
4
+1.866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00275_AB
FXP7000 Series
PARAMETER
Altitude
DESCRIPTION/CONDITIONS
Operating.
Non-Operating.
MIN
At 100% load:
At 50% load:
Operating Temperature
NOM
MAX
10k
40k
40
70
85
0
Storage Temperature
-40
UNITS
ASL Ft.
°C
°C
Temperature Coefficient
0°C to 70°C (after 15-minute warm-up).
.02
%/°C
Relative Humidity
Non-Condensing.
Operating: half-sine 10 ms, 3 axis
Non-operating: half-sine 10 ms, 3 axis
Operating: swept sine 5-2000-5 Hz, 5-32 Hz, 0.02îDA, 32-2000 Hz
Non-operating: random 10-2000 Hz
95
+20
+40
1
6.15
155
4.4
555
2.8
%RH
Shock
Vibration
Airflow
Airflow provided through the supply from front to rear.
PARAMETER
DESCRIPTION / CONDITIONS
MIN
Mechanical Dimensions
16.96" x 8.00" x 5.00" (430.8 mm x 203.2 mm x 127.0 mm)
Weight
13 kg (29 lb)
NOM
MAX
Gpk
Gpk
Grms
cfm
m3/min
Ifm
m/s
UNITS
Figure 1 - Rear and Front Views for FX76000
FRONT VIEW
5. 000"
(127m m )
REAR VIEW
LOCK HA NDLE
RE LEA SE
INP UT VOLT AGE RANGE
S E LE CT MODULE
ROTA TE 180 DEGREE S FOR 240 VAC
I NPUT VOLTA GE
DI SPLAY CUTOUT
2. 437"
(61. 90m m )
0. 521"
(13. 24m m )
CE NTE R
-TOCE NTE R
0. 090"
(2. 29m m )
2P L
48 0 VAC
4. 552"
(115. 62m m )
3. 901"
(99. 09m m )
0. 222"
(5. 64m m )
MATING CONNECTOR INFORMATION
Tyco PN
Elcon PN
Description
1648601-1
296-22-01100
CONN HSING FEM 52P TOP DRAWER
1648420-1
712-12-01107
CONTACT SOCKET #0 DOUBLE CROWN
1648318-1
702-32-01107
CONN SOCKET #12 BLIND MATE
1648325-1
702-92-01109
CONN SOCKET #20 BLIND MATE
CL
0. 226"
(5. 74m m )
CL
+1.866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00275_AB
FXP7000 Series
Figure 2 – FXC7000 Overall Size
16.09"
(408.7mm)
14.259"
(362.18mm)
11.704"
(297.28mm)
7.509"
(190.73mm)
MAIN TAIN 25 SQ IN MIN
F REE AREA (F RONT AND
REAR ) F OR AIR COOLING
A
A
A
4.954"
(125.83mm)
0.87"
(22.1mm)
A
LOC K H AND LE
L ED H AN D L E