G08-M02

Accessories Front Panels and DIN-Racks Front Panels Description Front panels are available for 19" DIN-rack mounting of 3 U cassette type power supplies in Schroff system version (Intermas system on request) and may be attached to the converter by means of countersunk screws. An assembly kit, consisting of a front panel and a support bracket, enables arrangement of two standard cassettes with up to six output voltages in 6 U configuration. All front panels are of colorless anodized aluminum and delivered with one or 2 grey plastic handles of 3 TE for easy pull-out and 2 or 4 hand-press insertable plastic retainers with captive screws for fixing to the rack. Note: Custom specific front panels are available on request. Dimensions according to DIN 41494-1 (IEC 60297): Width: 1 TE = 5.08 mm (0.20") Height: 1 U = 44.45 mm (1.750") Tolerances: ±0.2 mm, unless otherwise specified. Note: In Europa often HE instead of U is used. Schroff System for 3 U Rack Q-, P- Series Front Panels in 4, 5, or 6 TE 2.5±0.1 6.4 ±0.1 9.5 12002a These front panels available in three versions and fit to all DC-DC converters of the Q- and P-Series; see fig. 1 for the mechanical details. Table 1: Front panel selection for P and Q Series Designation G04-Q01 HZZ00835 P G04-Q04 HZZ00840 Q01 Q G05-Q01 HZZ00836 Q04 P G05-Q04 HZZ00841 Q G06-Q01 HZZ00839 6 30.2 Q01 Q04 P G06-Q04 HZZ00842 8 40.3 Q01 Q G08-Q01 HZZ00846 Q04 P G08-Q04 HZZ00850 104 ±0.1 Q Q04 4 13 Note: For using several units next to each other, we advise to pack them not too densely in order to assure good thermal management (see also relevant data sheet). X 9.2 ±0.1 Q01 50 Panel type 20.6 20.0 25.1 Conv. series 13 5 Case 0.2 4 X mm 128.4 122.4 TE Cut out for P Series only Delivery contents: Front panel, grey plastic handle, 3 countersunk screws, set of 2 plastic retainers with captive screws, and assembly instruction. Fig. 1 Front panel for P and Q Series converters MELCHER BCD.00495 Rev AB, 05-Mar-2015 The Power Partners. Page 1 of 5 Accessories Front Panels and DIN-Racks M and LH Series Front Panels in 8 TE 18.4 ±0.1 2.5 ±0.1 7 12004a This front panel fits to all 50 Watt DC-DC and AC-DC converters of the M Series (case M02) and LH Series (case H02). Table 2: Front panel selection for M and LH Series Panel type Designation M02 M H02 LH G08-M02 HZZ00802 12.2 26 100 ±0.1 Converter series 85 40.3 Case size 50.5 8 mm 128.4 122.4 TE Delivery contents: Front panel with grey plastic handle, 2 countersunk screws, set of 2 plastic retainers with captive screws, and assembly instruction. 0.2 12003a 9 40.3 (8 TE) 11.7 ±0.1 2.5 ±0.1 31.5 ±0.1 4.4 ±0.1 26 Fig. 3 Front panel for PSL Series 94.5 ±0.1 4 128.4 122.4 50 cut out for option D Front Panels 12 TE for S, HR, HRL, ER, ERL, PSS Front Panels 16 TE for K, HRP, ERP, PSK 0.2 18.2 ±0.1 These front panels fit to the converter series mentioned in the table below Table 4: Front panel selection for S, K, R, PSS, PSK Series 40.3 (8 TE) Width x TE mm Case size Converter series Panel type Designation 12 S01 PSS S02 S G12-S HZZ00845 60.6 Fig. 2 Front panel for M and LH Series ERL, HRL 16 PSL Series Front Panel in 8 TE This front panel fits to the Switching Regulators of the PSL Series (case size L04). Table 3: Front panel selection for PSL Series TE mm Case size 8 40.3 L04 Converter series Panel type Designation PSL G08-L HZZ00805 PSL with opt. D G08-L04-D HZZ00816 81.0 K01 PSK K02 K G16-K HZZ00831 ERP, HRP Delivery contents: Front panel with grey plastic handle, two countersunk screws, set of four plastic retainers with captive screws and assembly instructions. Delivery contents: Front panel with grey plastic handle, 2 countersunk screws, set of 2 plastic retainers with captive screws and assembly instructions. MELCHER BCD.00495 Rev AB, 05-Mar-2015 The Power Partners. Page 2 of 5 Accessories Front Panels and DIN-Racks 16.5 9 12007a 2 ±0.1 2.5 ±0.1 27.4 ±0.1 12005a 4.4 ±0.1 4 29 width x 9.7 ±0.1 0.2 16.5 128.4 122.4 103 ±0.1 50 0.6 width x cut out for option D Fig. 4 Front panel for S, K, R, PSS, PSK Series; see table 4 Fig. 5 Intermas system front panels (various case sizes) Intermas System for 3 U Rack The major differences between the Intermas and the Schroff system front panels are the thickness (2 mm instead of 2.5 mm), the hole size for the plastic retainers, and a small cutout on each side; see figure 5. All other dimensions are specified in the relevant Schroff front panel drawings. The following Intermas front panels are available on request: Table 6: Intermas front panel selection Width x TE mm Case size Converter series Panel type Designation LH F08-M02 HZZ00702 8 40.3 H02 M02 M 8 40.3 L04 PSL F08-L HZZ00705 PSL with opt. D F08-L04-D HZZ00716 S01 PSS S02 S, HR, HRL, ER, ERL F12-S HZZ00732 12 16 60.6 81.0 K01 PSK K02 K, HRP, ERP F16-K HZZ00731 Delivery contents: Front panel with grey plastic handle, 2 countersunk screws and assembly instructions. MELCHER BCD.00495 Rev AB, 05-Mar-2015 The Power Partners. Page 3 of 5 Accessories Front Panels and DIN-Racks Schroff System Kit for 6 U Rack 2.5 ±0.1 12008b To configure Power-One converters for use in 6 U racks, a special assembly kit has been created consisting of a doubleheight front panel together with a support bracket for 2 converters as shown in figure 6. All other dimensions are given in the relevant 3 U front panel drawings according to their case size. The assembly kit is available with the type designation according to the following table: Table 7: 6 U assembly kit selection 5 25.1 8 40.3 12 60.6 16 81.0 Case Converter size series Type Designation Q01 Q Kit G05-6HE-Q01 HZZ00838 Q04 P Kit G05-6HE-Q04 HZZ00844 H02 LH Kit G08-6HE-M02 HZZ00804 M02 M S01 PSS S02 S, HR, HRL, ER, ERL K01 PSK K02 K, HRP, ERP P Series only 261.8 255.8 Width x TE mm Support angel P/Q XMS052 Kit G12-6HE-S HZZ00833 Kit G16-6HE-K HZZ00832 Delivery contents: Double-height front panel with 2 grey plastic handles, 4 countersunk screws, set of 2 plastic retainers with captive screws, a support bracket, and assembly instruction. Supporting Angle P/Q HZZ1302-G P Series only 0.2 The kit contains the support angel XMS052-G and 2 counter sunk screws in a bag. width x Fig. 6 Front panel for 6 U configuration (various case sizes). Different additional holes depending on the model are not shown in the drawing. MELCHER BCD.00495 Rev AB, 05-Mar-2015 The Power Partners. Page 4 of 5 Accessories Front Panels and DIN-Racks DIN-Rack Systems Complete 19" rack with side walls, transversal rails, and mounting flanges. 6 guiding rails are included for set up of a system. The rails shall be fixed to the rack by the included screws (12 screws M2.5 x 12 and 12 nuts). The rack can be used for 19" cassette style converters such as Q, P, M, K, S, R, etc. (additional guiding rails XKR001-G may be necessary). Part no.: Size: Guiding rails: MQB02002G (system Rittal) 19" × 3 U / 84 HP (483 × 132 × 235 mm) HZZ01228-G (10 pcs XKR001-G in a bag) Enhanced version for Railway application (system Schroff): Part no.: Guiding rails: MQB02020G XAD.00056 485 mm (for 19") 465.1 mm (for 19") 450 mm (for 19") 19" = 482.6 mm 23" = 584.2 mm n • U, U = 1.75" = 44.45 mm 1U 6.35 mm 1U 6.35 mm 12056a 1 HP 1 HP = 0.2 " = 5.08 mm Fig. 7 19" DIN-Rack systems Dimensions in according to DIN 41494-1 (IEC 60297): Width: 1 HP (or TE) = 5.08 mm (0.20"); height: 1 U (or HE) = 44.45 mm (1.750") Tolerances ±0.2 mm, unless otherwise specified. NUCLEAR AND MEDICAL APPLICATIONS - These products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. www.belpowersolutions.com/power MELCHER BCD.00495 Rev AB, 05-Mar-2015 The Power Partners. Page 5 of 5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Bel Power Solutions: G08-M02 G12-S