S422-0010-A3

defining a degree of excellence Cat 12-R3 .20 Typ TRIPLE LINE LEADING EDGE CONTROL STANDARD DELAY MODULES .20 Typ 12 3 10 5 8 .325 .285 Max Vcc 14 In 1 Gnd 7 .80 Max .015 .004 .80 Max 4 o .375 .350 bel (DC) (P/N) * bel (DC) (P/N) .285 Max .22 Max .018 Coplanarity + .002 .23 Max .012 .008 .012 .008 100o 90o .20 Max .015 Min .045 .030 .12 Min .018 Part Numbers SMD S422-0005-A3 S422-0010-A3 S422-0015-A3 S422-0020-A3 S422-0025-A3 S422-0030-A3 S422-0035-A3 S422-0040-A3 S422-0045-A3 S422-0050-A3 S422-0060-A3 S422-0070-A3 S422-0080-A3 Thru-Hole A447-0005-A3 A447-0010-A3 A447-0015-A3 A447-0020-A3 A447-0025-A3 A447-0030-A3 A447-0035-A3 A447-0040-A3 A447-0045-A3 A447-0050-A3 A447-0060-A3 A447-0070-A3 A447-0080-A3 Time Delay 5 ns 10 ns 15 ns 20 ns 25 ns 30 35 40 45 ns ns ns ns Tolerance + 1.0 + 1.5 + 1.5 + 1.5 + 1.5 ns ns ns ns Rise Time 3 ns 3 ns 3 ns 3 ns 3 ns 3 ns 3 ns 3 ns 3 ns 3 ns 4 ns 4 ns 4 ns Vcc Vih Vil Ioh Iol Voh Vol Vik Iih Iil Ios Icch Iccl Ta PW d Tc Ein Trin PW PP Iccl Vcc Test Conditions @ 25oC Pulse Voltage Rise Time Pulse Width Pulse Period Supply Current Supply Voltage 3.2 Volts 3.0 ns (10%-90%) 1.2 x Total Delay 4 x Pulse Width 80 ma Typical 5.0 Volts 50 ns 60 ns 70 ns 80 ns ns + 1.5 ns + 1.5 ns + 2.0 ns + 2.0 ns + 2.5 ns + 3.0 ns + 3.5 ns + 4.0 ns Electrical Characteristics Supply Voltage Logic 1 Input Voltage Logic 0 Input Voltage Logic 1 Output Current Logic 0 Output Current Logic 1 Output Voltage Logic 0 Output voltage Input Clamp Voltage Logic 1 Input Current Logic 0 Input Current Short Circuit Output Current Logic 1 Supply Current Logic 0 Supply Current Operating Free Air Temperature Min. Input Pulse Width of Total Delay Maximum Duty Cycle Min. 4.75 2.0 Max. 5.25 0.8 -1 20 2.7 0.5 -1.2 20 -0.6 -150 70 90 70o 50 Units V V V ma ma V V V ua ma ma ma ma C % % Tolerances Input to Output + 5% , Unless otherwise specified Delays measured @ 1.5 V levels on Leading Edge only with 15pf loads on Outputs Rise and Fall Times measured from 0.75 V to 2.4 V levels -60 0o 100 Drive Capabilities Nh Logic 1 Fanout Nl Logic 0 Fanout 10 TTL Loads Max. 10 TTL Loads Max. Temp. Coeff. of Total Delay (TD) 100 + (25000/TD) PPM/OC Notes Transfer molded for better reliability Compatible with TTL & DTL circuits Terminals: Electro-Tin plate phosphor bronze Performance warranty is limited to specified parameters listed SMD - Tape & Reel available: 32mm Wide x 16mm Pitch, 500 pieces per 13" reel Recommended Temperature Profile 300o C 200 C 100o C Temp. o Infra Red 225o C Max Temp. > 185o C for 90 Seconds Max 0 2 4 6 Ti m e i n M i n u t e s 8 Other Delays and Tolerances Available Consult Sales Specifications subject to change without notice. Corporate Office Bel Fuse Inc. 198 Van Vorst Street, Jersey City, NJ 07302-4496 Tel: 201-432-0463 Fax: 201-432-9542 E-Mail: BelFuse@belfuse.com Internet: http://www.belfuse.com Far East Office Bel Fuse Ltd. 8F/8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel: 852-2328-5515 Fax: 852-2352-3706 European Office Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Preston PR1 8UD Lancashire, U.K. Tel: 44-1772-556601 Fax: 44-1772-888366 16