S560-6600-F9

ADSL Magnetics For Texas Instruments TNETD4000C • Designed to meet IEC 950 safety requirements for supplementary insulation at 250V Minimum interwinding breakdown voltage of 1500 Vrms Operating temperature range: -40° C to +85° C • • • • • Meets IEC 695, 2-2 flammability requirements PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias TM00327 ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Part Number Application Package Chip : Line ADSL over POTS - CO ADSL over ISDN - CO ADSL over POTS - CO Active Termination Line Side 1.5 mH ±5%1 75 µH ±5%2 Inductance Leakage Inductance µH max Line Side DCR Ω Max Chip Side 0.6 Line Side 1.25 Longitudinal Balance dB min 1 MHz Insertion Loss dB max 300 kHz Frequency Response dB 30 kHz 1.1 MHz ± 0.5 Harmonic Distortion dB max S560-6600-F7 SMD 1:2 8 55 0.5 -903 S560-6600-F8 SMD 1:2 3 0.28 0.28 55 0.5 ± 0.5 -903 S560-6600-F9 SMD 1:1 375 ±5%1 6 0.75 1.80 55 0.5 ± 0.5 -704 1. measured at 10 kHz, 0.1 Vac 2. measured at 100 kHz, 0.1 Vac 3. measured with 100 Ω source at 100 kHz, 15 Vp-p 4. measured with 100 Ω source at 40 kHz, 15 Vp-p SCHEMATIC S560-6600-F9 S560-6600-F7 S560-6600-F8 8 6 CHIP SIDE 7 5 1 10 1 LINE SIDE 7 4 3 LINE SIDE 2 4 CHIP SIDE ©2000 Bel Fuse Inc. Specifications subject to change without notice. 10.00 Bel Fuse Inc. 198 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com T3-71 ADSL Magnetics TM00327 For Texas Instruments TNETD4000C SUGGESTED PCB PAD LAYOUT 1 5 MECHANICAL S560-6600-F7 S560-6600-F8 0.741 (18.82) 0.060 (1.52) 0.028 (0.71) 0.540 (13.72) MAX 0.100 (2.54) 10 0.100 (2.54) 6 0.087 (2.21) 0.585 (14.86) MAX 0.500 (12.70) MAX 0.005 (0.13) 10 EDGES 0.606 (15.39) 0.699 (17.75) MAX 1 2 3 4 0.098 (2.50) 0.048 (1.22) 0.077 (1.96) 0.615 (15.62) S560-6600-F9 8 7 6 5 SUGGESTED PCB PAD LAYOUT 0.430 (10.92) MAX 0.480 (12.19) MAX 0.430 (10.92) MAX 0.004 (0.10) 0.024 (0.60) 0.098 (2.50) 0.492 (12.50) 0.600 (15.24) MAX 8 EDGES ©2000 Bel Fuse Inc. Specifications subject to change without notice. 10.00 CORPORATE Bel Fuse Inc. 198 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com T3-72