S560-6600-H3

HDSL2 & G.SHDSL Magnetics TM02305 • Designed to comply with the requirements of UL1950 and EN60950 to provide a supplementary insulation barrier with a working voltage of 250V Minimum interwinding breakdown voltage of 1500 Vrms Minimum interwinding breakdown voltage of 600 Vrms between pin 9 and 10 for 1 minute • • • Operating and storage temperature range: -40° to +85° C Meets IEC 695, 2-2 flammability requirements PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias • • • ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Part Number Chip : Line Line Side Line Side Chip Side Line Side 20 kHz 300 kHz 100 kHz 40 kHz 500 kHz 4 Vac 5 kHz Fundamental -78 Inductance1 mH ±7% Leakage Inductance2 µH max DCR Ω max Longitudinal Balance3 dB max Insertion Loss3 dB max Frequency Response3 dB Harmonic Distortion3 dB max S560-6600-H3 1 : 5.4 3.2 14 0.46 3.0 -55 0.5 ±0.3 All measurements are made with pins 2 and 3 connected and pins 6 and 7 connected 1. Inductance measured at 10 kHz, 0.1 Vac 2. Measured at 100 kHz, 0.1 Vac 3. Measured with line impedance of 135 Ω and chip impedance of 4.6 Ω SCHEMATIC S560-6600-H3 8 1 6 IC 7 3 Line 2 5 4 ©2002 Bel Fuse Inc. Specifications subject to change without notice. 05.02 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 HDSL2 & G.SHDSL Magnetics TM02305 MECHANICAL S560-6600-H3 Suggested PCB Pad Layout 0.077 [1.96] 0.615 [15.62] 0.048 [1.22] 0.490 [12.45] max 0.098 [2.50] 0.430 [10.92] max 0.450 [11.43] max 0.024 [0.61] 0.098 [2.50] 0.492 [12.50] 0.600 [15.24] max Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. Tape and Reel Packaging 32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID 200 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2002 Bel Fuse Inc. Specifications subject to change without notice. 05.02 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2