NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
RoHS Compliant
• • • •
SLIN-03F2Ax Features
• • • • • • • • • •
Rev.B
Wide Input Voltage Range Output Voltage Programmable Fixed Switching Frequency Remote On/Off Remote Sense
Over Temperature Protection Output Over Current Protection Ability to Sink and Source Current Cost Efficient Open Frame Design
Tunable LoopTM (a registered trademark of Lineage Power Systems) to Optimize Dynamic output voltage response Class 1, Category 2, Non-Isolated DC/DC Converter (refer to IPC-9592) Compliant to RoHS EU Directive 2002/95/EC UL* 60950-1 Recognized, CSA† C22.2 No. 60950-1-03 Certified VDE‡ 0805:2001-12 (EN60950-1) Licensed
Applications
• • • Distributed power architectures Intermediate bus voltage applications Telecommunications equipment • • • Servers and storage applications Networking equipment Industrial equipment
Description
The SLIN-03F2Ax power modules are non-isolated dc/dc converters that can deliver up to 3A of output current. These modules operate over a wide range of input voltage (VIN = 2.4Vdc-5.5Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 3.63Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current protection, and over temperature protection. A new feature, the Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area.
Part Selection
Output Voltage 0.6 Vdc - 3.63 Vdc Input Voltage 2.4 Vdc - 5.5 Vdc Max. Output Current 3A Typical Efficiency 91% Model Number Active High SLIN-03F2A0 Model Number Active Low SLIN-03F2AL
Notes: Add “G” suffix at the end of the model number to indicate Tray Packaging.
Part Number Explanation
S LIN – 03 F 2A 0
1 2 34 5 6 4--- Wide input voltage range (2.4-5.5V) 5--- Wide output voltage range (0.6-3.63V) 6--- Enable, active high, change “0” to “L” means active low
1---Surface mount 2---Series code 3---Output current (3A)
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
1
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output
Absolute Maximum Ratings
Parameter Continuous Input Voltage Operating Ambient Temperature Storage Temperature Min -0.3 -40 -55 Typ -
December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Max 6 85 125 Unit V °C °C Notes
Note: Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.
Input Specifications
Parameter Operating Input Voltage Input Current (full load) Input Current (no load) Input Stand-by Current Input Reflected Ripple Current (pk-pk) I2t Inrush Current Transient Input Ripple Rejection (120Hz) Turn-on Threshold Turn-off Threshold Hysteresis Min 2.4 1.75 0.08 Typ 26 75 2.1 25 40 Max 5.5 3.5 1 2.2 0.2 Unit V A mA mA mA mA A2s dB V V V Notes VIN=2.4V to 5.5V, IO=IO, max VIN=5.0V, Vo=0.6V, IO=0, module enabled VIN=5.0V, Vo=3.3V, IO=0, module enabled VIN = 5V, module disabled 5Hz to 20MHz, 1μH source impedance; VIN =0 to 5.5V, IO= IOmax
CAUTION: This converter is not internally fused. An input line fuse must be used in application. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 5A. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
2
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Min -1.5 -3.0 0.6 0 0 0 0 Typ 20 15 0.12 2 Max +1.5 +3.0 3.63 0.5 0.4 10 10 5 0.4 35 25 3 200 47 1000 3000 Unit %Vo,set %Vo,set V V %Vo,set mV mV mV %Vo,set mV mV A %Io,max A uF uF uF mS Hiccup Mode Vo≤250mV, Hiccup Mode Without the Tunable LoopTM With the Tunable LoopTM With the Tunable LoopTM Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo =10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo =10% of Vo, set) time for Vo to rise from 10% of Vo, set to 90% of Vo, set Vin=Vin, min to Vin, max, Io=Io, max, With or without maximum external capacitance mV uS mV uS di/dt=10A/us, Vin=5V, Vo=1.5V, Ta=25°C, Co=0 Line Regulation, VIN=VIN, min to VIN, max Load Regulation, IO=IO, min to IO, max Line Regulation, VIN=VIN, min to VIN, max Load Regulation, IO=IO, min to IO, max Tref=TA, min to TA, max 5Hz to 20MHz BW, VIN=VIN, nom and IO=IO, min to IO, max, Co = 0.1μF // 10 μF ceramic capacitors Notes with 0.5% tolerance for external resistor used to set output voltage Over all operating input voltage, resistive load, and temperature conditions until end of life selected by an external resistor
Output Specifications
Parameter Output Voltage Set Point Output Voltage Adjustment Range Remote Sense Range Output Regulation (for VO ≥ 2.5Vdc) Output Regulation (for VO < 2.5Vdc) Temperature Regulation Ripple and Noise (pk-pk) Ripple and Noise (rms) Output Current Range Output DC Current Limit Output Short-Circuit Current Output Capacitance ESR≥ 1 mΩ ESR≥0.15 mΩ ESR≥ 10 mΩ
Turn-On Delay Time 2 mS
Output voltage Rise time Output voltage overshoot Dynamic Load Response
△V0%~50% of
-
5 -
3
mS %Vo
Peak Deviation Settling Time Peak Deviation Settling Time
-
90 20 100 20
-
Max Load
△V50%~0% of
Max Load
Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
3
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
General Specifications
Parameter Efficiency Vo=0.6V Vo=1.2V Vo=1.8V Vo=2.5V Vo=3.3V Switching Frequency Over Temperature Protection Weight 81.2 89.4 91.4 93.9 94.4 600 140 1.55 % % % % % kHz °C g Calculated MTBF (Io=80% full load, Ta=40deg C) Telcordia Issue 2, Method I Case 3 Vin= 3.3Vdc, Ta=25°C Io=Io, max , Vo= Vo,set Vin=5.0V, when Vo=3.3V Min Typ Max Unit Notes
MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H)
16,139,760
hours
0.48 x 0.48 x 0.246 12.19 x 12.19 x 6.25
-
Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
4
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Efficiency Data
86 84 82
95
90
EFFICIENCY, η (%)
80 78 Vin=2.4V 76 74 72 70 0 0.5 1 1.5 2 2.5 3 Vin=3.3V Vin=5.5V
EFFICIENCY, η (%)
85
Vin=3.3V Vin=2.4V
Vin=5.5V
80
75
70 0 0.5 1 1.5 2 2.5 3
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, IO (A)
Vo=0.6V
95
100 95
Vo=1.2V
90
EFFICIENCY, η (%))
EFFICIENCY, η (%)
85
Vin=3.3V Vin=2.4V
Vin=5.5V
90 85 80 75 70 Vin=3.3V Vin=3V Vin=5.5V
80
75
70 0 0.5 1 1.5 2 2.5 3
0
0.5
1
1.5
2
2.5
3
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, IO (A)
Vo=1.8V
100 95
Vo=2.5V
EFFICIENCY, η (%))
90 85 80 75 70 0 0.5 1 1.5 2 Vin=5V Vin=4V
Vin=5.5V
2.5
3
OUTPUT CURRENT, IO (A)
Vo=3.3V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
5
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Thermal Derating Curves
3.5 3
3.5 3
OUTPUT CURRENT, Io (A)
2.5 2 1.5 1 0.5 0 LFM 0 20 30 40 50 60 70 80 90
OUTPUT CURRENT, Io (A)
2.5 2 1.5 1 0.5 0 LFM 0 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE, TA OC
AMBIENT TEMPERATURE, TA OC
Vo=0.6V
3.5 3 3.5 3
Vo=1.2V
OUTPUT CURRENT, Io (A)
2.5 2 1.5 1 0.5 0 LFM 0 20 30 40 50 60 70 80 90
OUTPUT CURRENT, Io (A)
2.5 2 1.5 1 0.5 0 LFM 0 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE, TA OC
AMBIENT TEMPERATURE, TA OC
Vo=1.8V
3.5 3
Vo=2.5V
OUTPUT CURRENT, Io (A)
2.5 2 1.5 1 0.5 0 LFM 0 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE, TA OC
Vo=3.3V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
6
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Ripple and Noise Waveforms
OUTPUT VOLTAGE VO (V) (20mV/div)
TIME, t (1μs/div)
OUTPUT VOLTAGE VO (V) (20mV/div)
TIME, t (1μs/div)
Vin=5V, Vo=0.6V, Io = Io,max
Vin=5V, Vo=1.2V, Io = Io,max
OUTPUT VOLTAGE VO (V) (20mV/div)
TIME, t (1μs/div)
OUTPUT VOLTAGE VO (V) (20mV/div)
TIME, t (1μs/div)
Vin=5V, Vo=1.8V, Io = Io,max
Vin=5V, Vo=2.5V, Io = Io,max
OUTPUT VOLTAGE VO (V) (20mV/div)
TIME, t (1μs/div)
Vin=5V, Vo=3.3V, Io = Io,max
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
7
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Transient Response Waveforms
OUTPUT VOLTAGE VO (V) (100mV/div)
OUTPUT CURRENT, IO (A) (1A/div)
TIME, t (20μs /div)
OUTPUT CURRENT, IO (A) (1A/div)
OUTPUT VOLTAGE VO (V) (100mV/div)
TIME, t (20μs /div)
Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=0.6V
OUTPUT VOLTAGE VO (V) (200mV/div)
Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=1.2V
OUTPUT VOLTAGE VO (V) (200mV/div)
OUTPUT CURRENT, IO (A) (1A/div)
TIME, t (20μs /div)
OUTPUT CURRENT, IO (A) (1A/div)
TIME, t (20μs /div)
Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=1.8V
OUTPUT VOLTAGE VO (V) (200mV/div)
Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=2.5V
OUTPUT CURRENT, IO (A) (1A/div)
TIME, t (20μs /div)
Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=3.3V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
8
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Startup Time
OUTPUT VOLTAGE VO (V) (200mV/div)
ON/OFF VOLTAGE VON/OFF (V) (2V/div)
TIME, t (1 ms/div)
ON/OFF VOLTAGE VON/OFF (V) (2V/div)
OUTPUT VOLTAGE VO (V) (500mV/div)
TIME, t (1 ms/div)
Start-up Using On/Off Voltage (Io = Io,max), Vo=0.8V
Start-up Using On/Off Voltage (Io = Io,max), Vo=1.2V
ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VON/OFF (V) (2V/div)
TIME, t (1 ms/div)
ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (2V/div)
TIME, t (1 ms/div)
Start-up Using On/Off Voltage (Io = Io,max), Vo=1.8V
Start-up Using On/Off Voltage (Io = Io,max), Vo=2.5V
ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (2V/div)
TIME, t (1 ms/div)
Start-up Using On/Off Voltage (Io = Io,max), Vo=3.3V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
9
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Startup Time (continued)
INPUT VOLTAGE VIN (V) (2V/div)
TIME, t (1 ms/div)
INPUT VOLTAGE VIN (V) (2V/div)
OUTPUT VOLTAGE VO (V) (500mV/div)
OUTPUT VOLTAGE VO (V) (200mV/div)
TIME, t (1 ms/div)
Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=0.8V
OUTPUT VOLTAGE VO (V) (1V/div)
Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=1.2V
OUTPUT VOLTAGE VO (V) (1V/div)
INPUT VOLTAGE VIN (V) (2V/div)
TIME, t (1 ms/div)
INPUT VOLTAGE VIN (V) (2V/div)
TIME, t (1 ms/div)
Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=1.8V
OUTPUT VOLTAGE VO (V) (1V/div)
Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=2.5V
INPUT VOLTAGE VIN (V) (2V/div)
TIME, t (1 ms/div)
Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=3.3V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
10
NON-ISOLATED DC/DC CONVERTERS
2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /3 A Output December 10, 2010
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Test Configurations
Input Reflected Ripple Current Test Setup.
TO OSCILLOSCOPE LTEST 1μH VIN(+) CURRENT PROBE
BATTERY
CS 1000μF Electrolytic E.S.R.