SLIN-06F1AL

NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. RoHS Compliant • • • SLIN-06F1Ax Features • • • • • • • • • • • Rev.B Wide Input Voltage Range Fixed Switching Frequency Remote Sense Ability to Sink and Source Current Cost Efficient Open Frame Design Over Temperature Protection Remote On/Off • Output Over Current Protection TM Tunable Loop (a registered trademark of Lineage Power Systems) to Optimize Dynamic output voltage response Flexible output voltage sequencing Class 1, Category 2, Non-Isolated DC/DC Converter (refer to IPC-9592) Compliant to RoHS EU Directive 2002/95/EC Compatible in a Pb-free or SnPb reflow environment UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified VDE‡ 0805:2001-12 (EN60950-1) Licensed Applications • • • Distributed power architectures Intermediate bus voltage applications Telecommunications equipment • • • Servers and storage applications Networking equipment Industrial equipment Description The SLIN-06F1Ax power modules are non-isolated dc-dc converters that can deliver up to 6A of output current. These modules operate over a wide range of input voltage (VIN=2.4Vdc-5.5Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 3.63Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and over temperature protection, and output voltage sequencing. A new feature, the Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. Part Selection Output Voltage 0.6 Vdc - 3.63 Vdc Input Voltage 2.4 Vdc - 5.5 Vdc Max. Output Current 6A Typical Efficiency 91% Model Number Active High SLIN-06F1A0 Model Number Active Low SLIN-06F1AL Notes: Add “G” suffix at the end of the model number to indicate Tray Packaging. Part Number Explanation S LIN – 06 F 1A 0 1 2 3 4 5 6 4--- Wide input voltage range (2.4-5.5V) 5--- Wide output voltage range (0.6-3.63V) 6--- Enable, active high, change “0” to “L” means active low 1---Surface mount 2---Series code 3---Output current (6A) Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 1 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Min -0.3 -0.3 -40 -55 Typ Max 6 Vin 85 125 Unit V V °C °C Notes Absolute Maximum Ratings Parameter Continuous Input Voltage Sequencing Voltage Operating Ambient Temperature Storage Temperature Note: Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Input Specifications Parameter Operating Input Voltage Input Current (full load) Input Current (no load) Vo=0.6V Vo=3.3V Input Stand-by Current Input Reflected Ripple Current (pk-pk) I2t Inrush Current Transient Input Ripple Rejection (120Hz) Turn-on Threshold Turn-off Threshold Hysteresis 1.75 0.08 30 75 2.2 25 40 1 2.2 0.2 mA mA mA mA A2s dB V V V VIN=5.0V, module enabled VIN = 5.0Vdc, module disabled 5Hz to 20MHz, 1μH source impedance; VIN =0 to 5.5V, IO= IOmax ; See Test Configurations Min 2.4 Typ Max 5.5 6.5 Unit V A Notes VIN=2.4V to 5.5V CAUTION: This converter is not internally fused. An input line fuse must be used in application. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6A. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 2 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Min -1.5 -3.0 0.6 0 0 0 0 Typ 25 10 0.23 2 Max +1.5 +3.0 3.63 0.5 10 5 0.4 10 0.4 35 15 6 200 47 1000 3000 Unit %Vo,set %Vo,set V V mV mV %Vo,set mV %Vo,set mV mV A %Io,max A uF uF uF mS Hiccup Mode Vo≤250mV, Hiccup Mode Without the Tunable LoopTM TM With the Tunable Loop With the Tunable LoopTM Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo =10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo =10% of Vo, set) time for Vo to rise from10% of Vo, set to 90% of Vo, set Vin=Vin, min to Vin, max, Io=Io, min to Io, max, With or without maximum external capacitance 5Hz to 20MHz BW, VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1μF // 10 μF ceramic capacitors) IO=IO, min to IO, max Notes with 0.5% tolerance for external resistor used to set output voltage Over all operating input voltage, resistive load, and temperature conditions until end of life selected by an external resistor Output Specifications Parameter Output Voltage Set Point Output Voltage Adjustment Range1 Remote Sense Range Load Regulation VO ≥ 2.5V VO < 2.5V Line Regulation VO ≥ 2.5V VO < 2.5V Temperature Regulation (-40°C to +85°C) Ripple and Noise (pk-pk) Ripple and Noise (rms) Output Current Range Output DC Current Limit Output Short-Circuit Current Output Capacitance ESR≥ 1 mΩ ESR≥0.15 mΩ ESR≥ 10 mΩ 1 VIN=VIN, min to VIN, max Turn-On Delay Time 2 mS Output voltage Rise time Output voltage overshoot Dynamic Load Response △V0%~50% of - 5 - 3 mS %Vo,set Peak Deviation Settling Time Peak Deviation Settling Time - 180 20 170 20 - mV uS mV uS di/dt=10A/us, Vin=5V, Vo=1.8V, Ta=25°C, Co=0 Max Load △V50%~0% of Max Load Notes: 1. External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best transient response (See the Tunable LoopTM section for details). 2. Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 3 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Min Vo=0.6V Vo=1.2V Vo=1.8V Vo=2.5V Vo=3.3V 10 Typ 72.3 82.7 87.7 91.4 93.0 600 140 Max Unit % % % % % kHz °C msec Delay from VIN, min to application of voltage on SEQ pin Vin, min to Vin, max; Io, min to Io, max, Vseq < Vo Notes Vin= 3.3Vdc, Ta=25°C Io=Io, max , Vo= Vo,set. When Vo=3.3V, Vin=5.0V General Specifications Parameter Efficiency Switching Frequency Over Temperature Protection Sequencing Delay time Tracking Accuracy Power-Up: 2V/ms Power-Down: 2V/ms Weight MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H) - 1.95 34,602,572 100 100 - mV mV g hours Calculated Per Bell Core SR-332 (Io=Io, max, Ta=40°C, Telecordia Issue 2 Method 1 Case 3) 0.48 x 0.48 x 0.29 12.19 x 12.19 x 7.25 - Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 4 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Efficiency Data 86 84 82 95 90 EFFICIENCY, η (%) 80 78 76 74 72 70 0 1 2 3 4 5 6 Vin=2.4V Vin=3.3V Vin=5.5V EFFICIENCY, η (%) 85 80 Vin=2.4V Vin=3.3V Vin=5.5V 75 70 0 1 2 3 4 5 6 OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=0.6V 95 100 95 90 Vo=1.2V EFFICIENCY, η (%)) 85 Vin=2.4V Vin=3.3V Vin=5.5V EFFICIENCY, η (%) 90 85 80 75 70 Vin=3V Vin=3.3V Vin=5.5V 80 75 70 0 1 2 3 4 5 6 0 1 2 3 4 5 6 OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=1.8V 100 95 Vo=2.5V EFFICIENCY, η (%)) 90 Vin=5.5V 85 80 75 70 0 1 2 3 4 5 6 Vin=5V Vin=4V OUTPUT CURRENT, IO (A) Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 5 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Thermal Derating Curves 6.2 6.0 5.8 5.6 5.4 5.2 5.0 20 30 40 50 60 70 O 6.2 6.0 5.8 5.6 5.4 5.2 5.0 20 30 40 50 60 70 O OUTPUT CURRENT, Io (A) 0.5m/s (100LFM) OUTPUT CURRENT, Io (A) NC 0.5m/s (100LFM) NC 80 90 80 90 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=0.6V 6.2 6.0 5.8 5.6 5.4 5.2 5.0 20 30 40 50 60 70 O Vo=1.2V 6.2 6.0 5.8 5.6 5.4 5.2 5.0 20 30 40 50 60 70 O OUTPUT CURRENT, Io (A) NC OUTPUT CURRENT, Io (A) NC 80 90 80 90 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=1.8V 6.2 6.0 5.8 5.6 5.4 5.2 5.0 20 30 40 50 60 70 O Vo=2.5V OUTPUT CURRENT, Io (A) NC 80 90 AMBIENT TEMPERATURE, TA C Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 6 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Ripple and Noise Waveforms OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vin=5V, Vo=0.6V, Io = Io,max Vin=5V, Vo=1.2V, Io = Io,max OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vin=5V, Vo=1.8V, Io = Io,max Vin=5V, Vo=2.5V, Io = Io,max OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vin=5V, Vo=3.3V, Io = Io,max Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 7 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Transient Response Waveforms OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT, IO (A) (2A/div) TIME, t (20μs /div) OUTPUT CURRENT, IO (A) (2A/div) OUTPUT VOLTAGE VO (V) (100mV/div) TIME, t (20μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=0.6V OUTPUT VOLTAGE VO (V) (100mV/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=1.2V OUTPUT VOLTAGE VO (V) (200mV/div) OUTPUT CURRENT, IO (A) (2A/div) TIME, t (20μs /div) OUTPUT CURRENT, IO (A) (2A/div) TIME, t (20μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=1.8V OUTPUT VOLTAGE VO (V) (200mV/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=2.5V OUTPUT CURRENT, IO (A) (2A/div) TIME, t (20μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vin=5V, Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 8 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Startup Time ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (200mV/div) VON/OFF (V) (2V/div) TIME, t (1 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VON/OFF (V) (2V/div) TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=0.6V Start-up Using On/Off Voltage (Io = Io,max), Vo=1.2V ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (500mV/div) TIME, t (1 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (2V/div) TIME, t (5 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=1.8V Start-up Using On/Off Voltage (Io = Io,max), Vo=2.5V ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (2V/div) TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 9 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Startup Time (continued) OUTPUT VOLTAGE VO (V) (200mV/div) TIME, t (1 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VIN (V) (2V/div) INPUT VOLTAGE VIN (V) (2V/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=0.6V Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=1.2V INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (2V/div) TIME, t (1 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (2V/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=1.8V Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=2.5V INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (2V/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 5V, Io = Io,max ), Vo=3.3V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 10 NON-ISOLATED DC/DC CONVERTERS 2.4 Vdc - 5.5 Vdc Input, 0.6 Vdc - 3.63 Vdc /6 A Outputs December 10, 2010 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. CURRENT PROBE Test Configurations Input Reflected Ripple Current Test Setup. TO OSCILLOSCOPE LTEST 1μH VIN(+) BATTERY CS 1000μF Electrolytic E.S.R.