SRAH-06E100

NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output xRAH-06Exx0 Series • • • • Non-Isolated Fixed Frequency (400 kHz) Remote On/Off RoHS Compliant • • • • Trim Function Rev.A OCP/SCP (Latch off) Low Profile Package (7.82 mm) UL60950-1 Recognized (UL/cUL) Under-voltage Lockout (UVLO) Description The Bel xRAH-06Exx0 is part of the low cost non-isolated dc/dc converter series. The modules use a surface mount package or vertical package for ease of layout and space savings, with a low profile of only 7.82 mm. The output is closely regulated and the efficiency of 3.3 Vdc output module is typically 91% at full load. Typical features include Remote On/Off, under-voltage lockout, over-current protection and short circuit protection. Part Selection Output Voltage 5.0 Vdc 3.3 Vdc 2.5 Vdc 1.8 Vdc 1.5 Vdc 1.2 Vdc 1.0 Vdc Input Voltage 8.0 Vdc - 13.2 Vdc 4.5 Vdc - 13.2 Vdc 4.5 Vdc - 13.2 Vdc 4.5 Vdc - 13.2 Vdc 4.5 Vdc - 13.2 Vdc 4.5 Vdc - 13.2 Vdc 4.5 Vdc - 13.2 Vdc Max. Output Current 6A 6A 6A 6A 6A 6A 6A Max. Output Power 30.0 W 19.8 W 15.0 W 10.8 W 9.0 W 7.2 W 6.0 W Typical Efficiency 94% 91% 89% 86% 84% 81% 79% Part Number Surface Mount SRAH-06E500 SRAH-06E330 SRAH-06E250 SRAH-06E180 SRAH-06E150 SRAH-06E120 SRAH-06E100 Part Number Vertical Mount VRAH-06E500 VRAH-06E330 VRAH-06E250 VRAH-06E180 VRAH-06E150 VRAH-06E120 VRAH-06E100 Notes: 1. Add “0” suffix at the end of the model number to indicate “Tube Packaging”, and “R” for “Reel Packaging”, and “G” for “Tray Packaging”. 2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Ambient Temperature Storage Temperature Min -0.3 V -0.3 V -40 °C -40 °C Typ Max 14 V 6.5 V 85 °C 125 °C Notes Input Specifications Parameter Input Voltage Input Current (full load) VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Min 4.5 V Typ Max 13.2 V 4.8 A 5.5 A 4.5 A 3.4 A 2.9 A 2.4 A 2.0 A Notes Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Input Specifications (continued) Parameter Input Current (no load) VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Remote Off Input Current Input Reflected Ripple Current (pk-pk) Min Typ 55 mA 50 mA 45 mA 40 mA 35 mA 32 mA 30 mA 2 mA 150 mA Max 95 mA 85 mA 75 mA 65 mA 60 mA 55 mA 50 mA 250 mA Notes When Vout=5 V ,Vin=8 V-13.2 V,Otherwise Vin=4.5 V-13.2 V Input Reflected Ripple Current (rms) I t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold 2 3.2 V 60 mA 0.04 A s 4.2 V 3.6 V 2 120 mA 0.1 A s 4.5 V 4.0 V 2 With simulated source impedance of 500 nH, 5 Hz to 20 MHz; use two 270 uF/16 V Oscon capacitors with ESR = 0.018 ohm max. at 100 kHz Only applicable to 1.0 V to 3.3 V output modules. Note: All specifications are typical at nominal input at 25 °C unless otherwise stated. Output Specifications Parameter Output Voltage Set Point VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Line Regulation VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Load Regulation VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Min 4.900 V 3.234 V 2.450 V 1.764 V 1.470 V 1.176 V 0.980 V Typ 5.0 V 3.3 V 2.5 V 1.8 V 1.5 V 1.2 V 1.0 V ±8 mV ±5 mV ±4 mV ±3 mV ±2 mV ±2 mV ±2 mV ±8 mV ±6 mV ±5 mV ±4 mV ±3 mV ±3 mV ±3 mV Max 5.100 V 3.366 V 2.550 V 1.836 V 1.530 V 1.224 V 1.020 V ±10 mV ±8 mV ±8 mV ±6 mV ±4 mV ±4 mV ±4 mV ±15 mV ±10 mV ±8 mV ±6 mV ±5 mV ±5 mV ±5 mV Notes Test condition: Vin=8 V, lout=half load Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input Parameter Regulation Over Temperature (-40 °C to 85 °C) VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Output Current Current Limit Threshold Short Circuit Surge Transient Ripple and Noise (rms) Ripple and Noise (pk-pk) Turn on Time Overshoot at Turn on Output Capacitance Transient Response 50% ~ 100% Max Load 100% ~ 50% Max Load Overshoot Settling Time Overshoot Settling Time VO=1.0 V -5.0 V 150 mV 100 uS 150 mV 100 uS 200 mV 150 uS 200 mV 150 uS di/dt = 0.5 A/uS; Vin = 8 V; with a 220 uF Tantalum capacitor at the output. 0 uF 1.0 Vdc - 5.0 Vdc/6 A Output Min Typ ±15 mV ±10 mV ±10 mV ±8 mV ±6 mV ±5 mV ±5 mV 0.003 A s 30 mV 50 mV 3% 2 Output Specifications (continued) Max ±30 mV ±20 mV ±20 mV ±15 mV ±12 mV ±10 mV ±8 mV 6A 15 A 0.006 A s 50 mV 100 mV 30 mS 7% 2400 uF 2 Notes - 0A 7A - Latch Off Latch Off BW = 0-20 MHz; with 1 uF ceramic capacitor & 10 uF Aluminum capacitor at the output. Note: All specifications are typical at 8 V input, full load at 25 °C unless otherwise stated. General Specifications Parameter Efficiency VO=5.0 V VO=3.3 V VO=2.5 V VO=1.8 V VO=1.5 V VO=1.2 V VO=1.0 V Switching Frequency Output Trim Range MTBF Dimensions (surface mount) Inches (L × W × H) Millimeters (L × W × H) Dimensions (vertical) Inches (L × W × H) Millimeters (L × W × H) Weight 91% 88% 86% 83% 81% 78% 76% 340 kHz 90% VO 94% 91% 89% 86% 84% 81% 79% 400 kHz 6,922,389 hours 0.78 x 0.7 x 0.32 19.81 x 17.78 x 8.13 0.7 x 0.308 x 0.65 17.78 x 7.82 x 16.51 5.5 g 460 kHz 110% VO Min Typ Max Notes Measured at Vin=8V, full load Calculated Per Bell Core SR-332 (Vin= 8 V; Vo=3.3 V; IO = 4.8 A; Ta = 25 °C) - - Note: All specifications are typical at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Control Specifications Parameter Remote On/Off Signal Low (Unit Off) Signal High (Unit On) -0.3 V 3.5 V 1.25 V 6.5 V Remote on/off pin open, unit on. Min Typ Max Notes Output Trim Equations Equations for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) and the nominal output voltage of the converter (Vnom) are shown below. The Trim Down resistor should be connected between the Trim pin and Vout. The Trim Up resistor should be connected between the Trim pin and Ground. Only one of the resistors should be used for any given application. Rtrim− down A = −B Vnom − Vadj Vout Rtrim-down Module Trim GND Vout Rtrim− up = Vadj C −D − Vnom Module Trim Rtrim-up GND Vnom 5.0 3.3 2.5 1.8 1.5 1.2 1.0 A 272.745 167.607 117.622 74.394 329.981 219.000 100.252 B 133.400 152.800 152.800 152.800 1365.000 666.000 898.000 C 37.140 37.140 37.140 37.140 219.000 219.000 149.400 D 71.500 90.900 90.900 90.900 1000.000 301.000 649.000 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Efficiency Data Efficiency Curve 100.0% 95.0% 90.0% Efficiency 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 0.6 1.5 3.0 4.5 6.0 Output current (A) Efficiency 100.0% 95.0% 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 0.6 1.5 3.0 4.5 6.0 Output current (A) 4.5 V 8V 13.2 V Efficiency Curve 8V 13.2 V Vo=5.0 V Efficiency Curve 100.0% 95.0% 90.0% Efficiency 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 0.6 1.5 3.0 4.5 6.0 Output current (A) Efficiency 100.0% 95.0% 90.0% Vo=3.3 V Efficiency Curve 4.5 V 8V 13.2 V 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 0.6 1.5 3.0 4.5 6.0 Output current (A) 4.5 V 8V 13.2 V Vo=2.5 V Efficiency Curve 95.0% 90.0% 4.5 V 8V 13.2 V Vo=1.8 V Efficiency Curve 95.0% 90.0% Efficiency 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 4.5 V 8V 13.2 V Efficiency 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 0.6 1.5 3.0 4.5 6.0 Output current (A) 0.6 1.5 3.0 4.5 6.0 Output current (A) Vo=1.5 V Efficiency Curve 90.0% 85.0% Efficiency 80.0% 75.0% 70.0% 65.0% 60.0% 0.6 1.5 3.0 4.5 6.0 Output current (A) Vo=1.2 V 4.5 V 8V 13.2 V Vo=1.0 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Thermal Derating Curves Vo=3.3 V - 5.0 V Vo=1.0 V - 2.5 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Ripple and Noise Waveforms Ripple and noise at max load 5.0 Vdc output Ripple and noise at max load 3.3 Vdc output Ripple and noise at max load 2.5 Vdc output Ripple and noise at max load 1.8 Vdc output Ripple and noise at max load 1.5 Vdc output Ripple and noise at max load 1.2 Vdc output Ripple and noise at max load 1.0 Vdc output Note: Ripple and Noise at 8 Vdc input, 0-20 MHz BW, with 1 uF ceramic capacitor & 10 uF Aluminum capacitor at the output, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Transient Response Waveforms Transients 50% to 100% load 5 Vdc output Transients 100% to 50% load 5 Vdc output Transients 50% to 100% load 3.3 Vdc output Transients 100% to 50% load 3.3 Vdc output Transients 50% to 100% load 2.5 Vdc output Transients 100% to 50% load 2.5 Vdc output Transients 50% to 100% load 1.8 Vdc output Transients 100% to 50% load 1.8 Vdc output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Transient Response Waveforms (continued) Transients 50% to 100% load 1.5 Vdc output Transients 100% to 50% load 1.5 Vdc output Transients 50% to 100% load 1.2 Vdc output Transients 100% to 50% load 1.2 Vdc output Transients 50% to 100% load 1.0 Vdc output Transients 100% to 50% load 1.0 Vdc output Note: Transient Response at 12 V input, di/dt=0.5 A/uS, with 220 uF tantalum cap at the output, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 13.2 Vdc Input 1.0 Vdc - 5.0 Vdc/6 A Output Mechanical Outline SRAH-06Exx0 Pin Connections bel Pin 1 2 3 4 5 6 7 Function Remote On/Off Vin Ground Vout Trim N/A N/A VRAH-06Exx0 Pin Connections bel Pin 1 2 3 4 5 Function Remote On/Off Vin Ground Vout Trim bel RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. These parts are not however compatible with the higher temperatures associated with lead free solder processes and must be soldered using a reflow profile with a peak temperature of no more than 240 ºC. ©2007 Bel Fuse Inc. Specifications subject to change without notice. 010507 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com