SRBA-06A2A0

NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output SRBA-06A2Ax • • • • • • Non-Isolated High Efficiency High Power Density Fixed Frequency Remote On/Off Active Low/High RoHS Compliant • • • • • Rev.A Under-Voltage Lockout (UVLO) OCP/SCP Wide Input Wide Trim Range Flexible Output Voltage Sequencing Description The Bel SRBA-06A2Ax modules are a series of non-isolated dc/dc converters that deliver up to 6 A of output current with full load efficiency of 92% at 5.0 Vdc output. These modules provide precisely regulated voltage programmable via external resistor from 0.75 Vdc to 5.5 Vdc over a wide range of input voltage (8.3 Vdc - 14 Vdc). These modules have a sequencing feature that enables designers to implement various types of output voltage sequencing when powering multiple voltages on a board. The open-frame construction and small footprint enable designers to develop cost and space-efficient solutions. Standard features include remote On/Off, over current protection, short current protection, wide input, and programmable output voltage. Part Selection Output Voltage 0.75 V - 5.5 V Input Voltage 8.3 V - 14 V Max. Output Current 6A Max. Output Power 33 W Typical Efficiency 92% Model Number Active Low SRBA-06A2AL Model Number Active High SRBA-06A2A0 Notes: 1. Add “G” suffix at the end of the model numbers listed above to indicate “Tray Packaging” 2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Sequencing Voltage 1 Min -0.3 V -0.3 V -0.3 V -40 °C -55 °C Typ - Max 15 V 15 V Vin 85 °C 125 °C Notes Ambient Temperature Storage Temperature Notes: All specifications are typical at 25 °C unless otherwise stated. 1. SRBA-06A2Ax series of modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When the sequencing feature is not used, tie the SEQ pin to Vin or leave the SEQ pin floating. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Input Specifications Parameter Input Voltage Input Current (full load) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.2 V Vo=0.75 V Input Current (no load) Vo=5.0 V Vo=0.75 V Remote Off Input Current Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (rms) I t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold 2 Min 8.3 V - Typ 12 V 2.75 A 1.85 A 1.45 A 1.05 A 0.75 A 0.55 A 1 mA 120 mA 40 mA 0.002 A s 8.1 V 7.5 V 2 Max 14 V 4.0 A 2.8 A 2.2 A 1.6 A 1.1 A 0.8 A 100 mA 20 mA 2 mA 0.02 A s 8.2 V 8.0 V 2 Notes Tested with two 100 uF/25 V tan input capacitors & simulated source impedance of 1 uH, 5 Hz to 20 MHz. Notes: All specifications are typical at 25 °C unless otherwise stated. Output Specifications Parameter Output Voltage Set Point Output Voltage Set Point Adjustment Range Selected by External Resistor or Voltage Load Regulation Line Regulation Regulation Over Temperature (-40 °C to +85 °C) Output Current Current Limit Threshold Short Circuit Surge Transient Ripple and Noise (pk-pk) Vo=0.75 V-3.63 V Ripple and Noise (rms) Vo=0.75 V-3.63 V Ripple and Noise (pk-pk) Vo=5.0 V Ripple and Noise (rms) Vo=5.0 V Turn on Time Overshoot at Turn on Output Capacitance ESR ≥ 1 mohm ESR ≥ 10 mohm Min -2%Vo,set -2.5%Vo,set 0.7525 V 0A 7.2 A 0 uF 0 uF Typ 0.4%Vo,set 0.3%Vo,set 0.5%Vo,set 0.25 A s 50 mV 15 mV 75 mV 30 mV 8 mS 0% 2 Max 2%Vo,set 3.5%Vo,set 5.5 V 6A 18 A 75 mV 30 mV 100 mV 40 mV 10 mS 3% 1000 uF 3000 uF Notes Vin=12 V, full load Over all operating input voltages, resistive loads and temperature conditions Io=Io, min to Io, max Vin=Vin, min to Vin, max Tref=Ta, min to Ta, max Tested with 0-20 MHz, with 10 uF/10 V tantalum capacitor & 1 uF/10 V TDK ceramic capacitor at the output. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Output Specifications (continued) Parameter Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time VO = 0.75 - 5.5 V 200 mV 50 uS 200 mV 50 uS di/dt=2.5 A/uS; Vin=12 V; and with 10 uF/10 V tantalum capacitor & 1 uF/ 10 V ceramic capacitor at the output. Min Typ Max Notes Note: All specifications are typical at nominal input (Vin=12 V), full load at 25 °C unless otherwise stated. General Specifications Parameter Efficiency Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.2 V Vo=0.75 V Switching Frequency Over Temperature Shutdown Output Trim Range (wide trim) MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H) Weight 0.8 x 0.45 x 0.251 20.32 x 11.42 x 6.38 3g 90% 87% 85% 83% 79% 71% 250 kHz 0.7525 V 92% 89% 88% 86% 82% 74% 300 kHz 135 °C 3,079,469 hours 350 kHz 5.5 V Calculated Per Bell Core SR-332 (IO = Nominal; Ta = 25 °C) Measured at Vin=12 V, full load Min Typ Max Notes - Note: All specifications are typical at 25 °C unless otherwise stated. Control Specifications Parameter Signal Low (Unit Off) Signal High (Unit On) Signal Low (Unit On) Signal High (Unit Off) Sequencing Voltage Sequencing Slew Rate Capability Sequencing Delay Time Tracking Accuracy Power-Up Power-Down 100 mV 200 mV 200 mV 400 mV Min -0.3 V 2.5 V -0.3 V 2.5 V 0V 10 mS Typ Max 0.4 V 14 V 0.4 V 14 V Vin 2 V/mS Delay from Vin, min to application of voltage on SEQ pin Notes SRBA-06A2A0; Remote On/Off pin open, Unit on. SRBA-06A2AL; Remote On/Off pin open, Unit on. Sequencing Voltage applied on SEQ pin should be higher than output voltage. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Output Trim Equations Equation for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground. Vout Rtrim 10.507 = −1 Vadj − 0.7525 Module Trim GND Rtrim Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. Vout Vtrim = 0.7 − 0.0667 × (Vadj − 0.7525) Module Trim Vtrim GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Efficiency Data MODULE 3.3V 95.0% 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 1A 2A 3A 4A 5A 6A OUTPUT CURRENT MODULE 5.0V 100.0% EFFICIENCY 95.0% 90.0% 85.0% 80.0% 75.0% 1A 2A 3A 4A 5A 6A OUTPUT CURRENT 8.3V 12.0V 14.0V EFFICIENCY 8.3V 12.0V 14.0V MODULE 2.5V 95.0% 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 1A 2A 3A 4A 5A 6A OUTPUT CURRENT MODULE 1.8V 95.0% 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 1A 2A 3A 4A 5A 6A OUTPUT CURRENT EFFICIENCY EFFICIENCY 8.3V 12.0V 14.0 V 8.3V 12.0V 14.0 V MODULE 1.2V 90.0% EFFICIENCY 80.0% 70.0% 60.0% 50.0% 1A 2A 3A 4A 5A 6A OUTPUT CURRENT MODULE 0.75V 90.0% EFFICIENCY 8.3V 12.0V 14.0V 80.0% 70.0% 60.0% 50.0% 1A 2A 3A 4A 5A 6A OUTPUT CURRENT 8.3V 12.0V 14.0 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Thermal Derating Curves Vin=12 V, Vo=0.75 V Vin=12 V, Vo=2.5 V Vin=12 V, Vo=5.0 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Ripple and Noise Waveforms Ripple and noise at full load, Vin=12 V, Vo=0.75 V Ripple and noise at full load, Vin=12 V, Vo=1.2 V Ripple and noise at full load, Vin=12 V, Vo=1.8 V Ripple and noise at full load, Vin=12 V, Vo=2.5 V Ripple and noise at full load, Vin=12 V, Vo=3.3 V Ripple and noise at full load, Vin=12 V, Vo=5.0 V Note: The output ripple and noise is tested at 0-20 MHz BW, 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic capacitor, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Transient Response Waveforms 50% to 100% load step at Vin=12 V, Vo=0.75 V 100% to 50% load step at Vin=12 V, Vo=0.75 V 50% to 100% load step at Vin=12 V, Vo=1.2 V 100% to 50% load step at Vin=12 V, Vo=1.2 V 50% to 100% load step at Vin=12 V, Vo=1.8 V 100% to 50% load step at Vin=12 V, Vo=1.8 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Transient Response Waveforms (continued) 50% to 100% load step at Vin=12 V, Vo=2.5 V 100% to 50% load step at Vin=12 V, Vo=2.5 V 50% to 100% load step at Vin=12 V, Vo=3.3 V 100% to 50% load step at Vin=12 V, Vo=3.3 V 50% to 100% load step at Vin=12 V, Vo=5.0 V 100% to 50% load step at Vin=12 V, Vo=5.0 V Note: Transient response is tested at di/dt=2.5 A/uS, with 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic capacitor, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.5 Vdc/6 A Output Mechanical Outline Pin Connections Pin 1 2 3 4 5 6 Function Remote On/Off Vin+ SEQ Ground Trim Vout+ RECOMMENDED PAD LAYOUT PAD SIZE: MIN: 0.12"* 0.095" (3.05mm * 2.41mm) MAX: 0.135"* 0.11" (3.43mm * 2.79mm) RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. ©2007 Bel Fuse Inc. Specifications subject to change without notice. 011207 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com