SRBC-16A1A_07

NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output SRBC-16A1Ax • • • • • • • • Non-Isolated High Efficiency High Power Density RoHS Compliant • • • • • • • • Rev.A Under-voltage Lockout (UVLO) Over Temperature Protection OCP/SCP Wide Input Wide Trim Remote On/Off Active Low/High (option) Remote Sense Excellent Thermal Performance Low Cost Flexible Output Voltage Able to Sink & Source Current Industrial Temperature Range Description The Bel SRBC-16A1Ax modules are a series of non-isolated dc/dc converters that deliver up to 16 A of output current with full load efficiency of 92% at 3.3 Vdc output. These modules provide precisely regulated voltage programmable via external resistor from 0.75 Vdc to 5.0 Vdc over a wide range of input voltage (8.4 Vdc -14 Vdc). The open-frame construction and small footprint enable designers to develop cost and space-efficient solutions. Standard features include remote On/Off, remote sense, over current protection, short current protection, and programmable output voltage. Part Selection Output Voltage 0.75 Vdc- 5.0 Vdc Input Voltage 8.3 Vdc -14 Vdc Max. Output Current 16 A Max. Output Power 80 W Typical Efficiency 94% Model Number Active Low SRBC-16A1AL Model Number Active High SRBC-16A1A0 Notes: 1.Add “G” suffix at the end of the model number to indicate Tray Packaging. 2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Ambient Temperature Storage Temperature Min -0.3 V -0.3 V -40 °C -55 °C Typ Max 15 V 15 V 85 °C 125 °C Notes Note: All specifications are typical at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Input Specifications Parameter Input Voltage Vo, set ≤ 3.63 V Vo, set > 3.63 V Input Current (full load) Input Current (no load) Remote Off Input Current Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (rms) I2t Inrush Current Transient Turn-on Voltage Threshold Turn-off Voltage Threshold 8.3 V 8.3 V 12 V 12 V 100 mA 2 mA 70 mA 14.0 V 13.2 V 11 A 200 mA Tested with one 1000 uF/25 V AL input capacitor with ESR=0.03 ohm max and 6 × 47 uF/16 V tantalum capacitors with ESR=0.013 ohm max at 100 kHz, & simulated source impedance of 1000 nH, 5 Hz to 20 MHz. This power module is not internally fused. An input line fuse must always be used. Min Typ Max Notes - 0.2 A2s 8.0 V 7.5 V 150 mA 0.4 A2s - Output Specifications Parameter Output Voltage Set Point Load Regulation Line Regulation Regulation Over Temperature (-40 °C to+85 °C) Output Current Current Limit Threshold Short Circuit Surge Transient Ripple and Noise (pk-pk) Ripple and Noise (rms) Turn on Time Overshoot at Turn on Output Capacitance ESR ≥ 10 mohm Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time VO=0.75 V 5.0 V 100 mV 50 uS 100 mV 50 uS di/dt=2.5 A/uS; Vin=12 V; and with 2 × 150 uF polymer capacitors at the output Min -2% Vo,set 0A 0 uF Typ 0.1% Vo,set 0.1% Vo,set 0.3% Vo,set 180% Io,out 1A s 75 mV 30 mV 6 mS 2 Max 2% Vo,set 16 A 3A s 100 mV 45 mV 10 mS 1% Vo,set 5000 uF 2 Notes Vin=12 V, full load Io=Io, min to Io, max Vin=Vin, min to Vin, max Tref=Ta, min to Ta, max Tested with 0-20 MHz, 10 uF tantalum capacitor & 1 uF TDK ceramic capacitor at the output Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output General Specifications Parameter Efficiency Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=0.75 V Switching Frequency Over Temperature Shutdown 1 Min 265 kHz 0.7525 V - Typ 94% 92% 90% 88% 87% 85% 79% 300 kHz 130 °C 2,666,488 hours Max 335 kHz 5.0 V 0.5 V Notes Measured at Vin=12 V, full load Output Trim Range (Wide Trim) Remote Sense Compensation MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H) Weight Calculated Per Bell Core SR-332 (IO = Nominal; Ta = 25 °C) 1.30 x 0.53 x 0.315 33.02 x 13.46 x 8.00 8g - Notes: All specifications are typical at 25 °C unless otherwise stated. 1. The Tref temperature measurement location: Control Specifications Parameter Remote On/Off Signal Low (Unit Off) Signal High (Unit On) Signal Low (Unit On) Signal High (Unit Off) -0.2 V -0.2 V 2.5 V 0.3 V Vin, max 0.3 V Vin, max SRBC-16A1A0; Remote On/Off pin open, Unit on. SRBC-16A1AL; Remote On/Off pin open, Unit on. Min Typ Max Notes Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Remote Enable Specifications The SRBC-16A1AL modules feature an enable pin with negative logic. If not using the enable pin, leave the pin open (the module will be on). During logic_high, the module is turned off, during logic_low, the module is turned on. It inner circuit impedance is showed as figure. SRBC-16A1AL The SRBC-16A1A0 modules feature an enable pin with Positive logic. If not using the enable pin, leave the pin open (the module will be on). During logic_high, the module is turned on, during logic_low, the module is turned off. It inner circuit impedance is showed as figure. SRBC-16A1A0 Output Trim Equations Equation for calculating the trim resistor (in Ω) given the desired adjusted voltage (Vadj) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground. Vout 10500 − 1000 Rtrim = Vadj − 0.7525 Sense Module trim Rtrim GND Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. Vout Sense Vtrim = 0.7 − 0.0667 × (Vadj − 0.7525) Module trim Vtrim GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Thermal Derating Curves Vo=0.75 V Vo=1.8 V Vo=3.3 V Vo=5.0 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Efficiency Data Module 5.0V 98.0% 96.0% Efficiency 94.0% 92.0% 90.0% 88.0% 86.0% 84.0% 2.0 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 8.3V 12.0V 13.2V Module 3.3V 96.0% 94.0% Efficiency 92.0% 90.0% 88.0% 86.0% 84.0% 2.0 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 8.3V 12.0V 14.0V Module 2.5V 96.0% 94.0% Efficiency 92.0% 90.0% 88.0% 86.0% 84.0% 82.0% 2.0 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 8.3V 12.0V 14.0V Module 1.8V 94.0% 92.0% Efficiency 90.0% 88.0% 86.0% 84.0% 82.0% 80.0% 2.0 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 8.3V 12.0V 14.0V Module 1.5V 94.0% 92.0% 90.0% Efficiency 88.0% 86.0% 84.0% 82.0% 80.0% 78.0% 2.0 8.3V 12.0V 14.0V Module 1.2V 92.0% 90.0% Efficiency 88.0% 86.0% 84.0% 82.0% 80.0% 78.0% 76.0% 2.0 8.3V 12.0V 14.0V 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 Module 0.75V 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 55.0% 50.0% 2.0 Efficiency 8.3V 12.0V 14.0V 4.0 6.0 8.0 10.0 12.0 Output Current 14.0 16.0 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Ripple and Noise Waveforms Ripple and noise at max load 0.75 Vdc output Ripple and noise at max load 1.2 Vdc output Ripple and noise at max load 1.5 Vdc output Ripple and noise at max load 1.8 Vdc output Ripple and noise at max load 2.5 Vdc output . Ripple and noise at max load 3.3 Vdc output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Ripple and Noise Waveforms (continued) Ripple and noise at max load 5.0 Vdc output Note: Ripple and Noise at 12 V input, with 10 uF tantalum capacitor and 1 uF ceramic capacitor at the output, and Ta=25 deg C. Transient Response Waveforms Transients 50% to 100% load 0.75 Vdc output Transients 100% to 50% load 0.75 Vdc output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Transient Response Waveforms (continued) Transients 50% to 100% load 1.2 Vdc output Transients 100% to 50% load 1.2 Vdc output Transients 50% to 100% load 1.5 Vdc output Transients 100% to 50% load 1.5 Vdc output Transients 50% to 100% load 1.8 Vdc output Transients 100% to 50% load 1.8 Vdc output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Transient Response Waveforms (continued) Transients 50% to 100% load 2.5 Vdc output Transients 100% to 50% load 2.5 Vdc output Transients 50% to 100% load 3.3 Vdc output Transients 100% to 50% load 3.3 Vdc output Transients 50% to 100% load 5.0 Vdc output Transients 100% to 50% load 5.0 Vdc output Note: Transient response at 12 V input, di/dt=2.5 A/uS, with external 2 x 150 uF polymer capacitor at the output, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/16 A Output Mechanical Outline Pin Connections Pin 1 2 3 Function Remote On/Off Vin N/A Ground Vout Trim Remote Sense BOTTOM VIEW RECOMMENDED PAD LAYOUT 4 5 6 7 PAD SIZE: MIN: 0.14"* 0.095" (3.56mm * 2.41mm) MAX: 0.165"* 0.11" (4.19mm * 2.79mm) RoHS Compliance Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products. ©2007 Bel Fuse Inc. Specifications subject to change without notice. 011507 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com