V7NB-60A16

NON-ISOLATED DC/DC CONVERTERS 12V Input / Programmable Output / 60A VRM 9/10 Compatible V7NB-60A160 • • • Remote on/off 2-Wire Remote sense Optional 5 bit or 6 bit VID schemes o Intel VRM 9.x compatible 1.1V to 1.6V o Intel VRM 10.x compatible 0.8375V to 1.6V Adaptive voltage positioning Wider input range available – consult factory • • Description The V7NB-60A Series are non-isolated step down DC/DC converters providing up to 60A of peak output current and designed to be compatible to the Intel VRM 9 and VRM10 VID codes (maximum output voltage = 1.6V). Standard features include remote on/off, over current protection, remote sense and a power good signal. This product also makes use of adaptive positioning to improve transient response performance. Typical applications include file servers, work stations and other computing applications. Part Selection Output Voltage 0.83 – 1.6V Input Voltage 12V Output Current (Thermal Design) 30A Output Current (Peak Current) 60A Typical Efficiency 82% Model Number V7NB-60A160 Input Specifications Parameter Input Voltage Range Input Current (disabled) Input Current (full load) Reflected Ripple Current Min 10.3 VDC Typ 30mA 11.5A 150mA rms With 100uF, 25mOhm capacitor and 200nH of input inductance. Max 13.2 VDC Notes Output Specifications Parameter Output Current Set Point Accuracy Adaptive Positioning (Droop Impedance) Ripple and Noise Min 0A 1.26V Typ 1.28V 1.0 mOhm 30mV pk-pk, 0 to 20MHz Bandwidth Full load with 3 X 470uF polymer + 500uF ceramic on output. 16mS di/dt = 50A/uS Load step =0A to 60A. Cout = 3 X 470uF polymer + 500uF ceramic For applications requiring higher or lower output capacitance please consult Max 30A 60A 1.30V Notes Thermal design Peak current rating no load, excluding Adaptive positioning, VID 10110 Turn on Time Transient Response Deviation Settling Time Remote Sense Compensation Output Capacitance 8mS 90mV 100uS ±0.3VDC 2400uF Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 12V Input / Programmable Output / 60A VRM 9/10 Compatible factory. General Specifications Parameter Switching Frequency Dimensions inches mm Operating Temperature Non-Operating Temperature Protection Features Over current Undervoltage Remote On/Off Efficiency (full load) 1.30V output Specification 1.4 MHz typical (fixed) 3.8 x 1.0 x 0.40 96.5 x 25.4 x 10.2 0°C to 60°C -40°C to 100°C 110% to 170% max Io UVLO Vin < 9.5V Active High 82% V7NB-60A160 Derating Curve 40 35 30 Output Current (A) 25 125 LFM 20 15 40 LFM 0 LFM 10 5 0 0 10 20 30 Temperature (ºC) 40 50 60 2004 Bel Fuse Inc. Specifications subject to change without notice. 040407 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 12V Input / Programmable Output / 60A VRM 9/10 Compatible Pin Connections Row A Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Row B Pin 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 Function VIN+ VIN+ VIN+ VIN+ Reserved No pin VID3 VID1 TRIM (note 1) PWRGD VO-senReserved VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VO- Function VINVINVINVINVRM-pres VID4 VID2 VID0 NC (note 3) OUTEN VO-sen+ VID5 (note 2) VO+ VO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VOVO+ VO- Notes: 1. Consult factory for trim option. 2. Pin 51 is VID5 for VRM10 applications. If you are not using this pin, leave it floating. Consult factory for VRM10 VID table. 3. Current share is not implemented on this module. Consult factory for applications requiring current share. 4. Module leads, header, and any portion of the component that is exposed directly to molten solder will withstand a temperature of 260 degrees C for a minimum of 10 seconds. Component sections not exposed directly to the solder will withstand 150 degrees C. Lead Solderability meets ANSI/J-STD-002. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 12V Input / Programmable Output / 60A VRM 9/10 Compatible Signal Definitions Symbol VIN+ VINInput power to the converter Common return for both input and output Logic level inputs used to set the output voltage, refer to VID table below. Connect these pins either to open-drain outputs with or without external pull-up resistors or to active-pull-up outputs. VID0VID5 have 20uA internal pull-up current sources that diminish to zero as the voltage rises above 2.5V. These inputs can be pulled up as high as 5.3V. See note 2. Optional trim pin, used to adjust the output voltage. See note 1. The open drain power good signal detects output under voltage only. It transitions to the high state after soft start has completed. If the output voltage falls below 74% of the nominal VID voltage, the signal is de-asserted. Remote voltage sense lines. Connect these at the point of load, to VO+ and VO- respectively. Common return for both input and output Output voltage available to the load. Logic level input used to enable the converter when high. Pin is tied to ground on module and is used by system to detect if a VRM is present. Definitions VID0, VID1, VID2, VID3, VID4, VID5 Trim PWRGD VO-sen+ VO-senVOVO+ OUTEN VRM-pres 2004 Bel Fuse Inc. Specifications subject to change without notice. 040407 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 12V Input / Programmable Output / 60A VRM 9/10 Compatible Voltage Identification (VID) Code VID4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 VID3 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 VID2 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 VID1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 VID0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Vo (VDC) Output Off 1.1 1.125 1.15 1.175 1.2 1.225 1.25 1.275 1.3 1.325 1.35 1.375 1.4 1.425 1.45 1.475 1.5 1.525 1.55 1.575 1.6 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com