X7AH-01FXX0

NON-ISOLATED DC/DC CONVERTERS 3.0 V-5.5 V Input 12 V/0.8 A & 15 V/0.6 A Output x7AH-01Fxx0 Series • • • • Non-Isolated Fixed Frequency (550 kHz) High Efficiency Low Profile Package • • Trim Function (option) Allows Burst Mode Operation at Low Load Currents Description The Bel x7AH-01Fxx0 is part of the low cost non-isolated dc/dc converter series. The modules use a surface mount package or vertical package for ease of layout and space savings. The output is closely regulated and the efficiency of 12 V output module is typically 88% at full load. Typical features include burst mode operation at light load and trim function (option). Part Selection Output Voltage 12 V 15 V Input Voltage 3.0 V – 5.5 V 3.0 V – 5.5 V Max. Output Current 0.8 A 0.6 A Max. Output Power 9.6 W 9.0 W Typical Efficiency 88% 88% Part Number Surface Mount S7AH-01FX20 S7AH-01FX50 Part Number Vertical Mount V7AH-01FX20 V7AH-01FX50 Note: Add “0” suffix at the end of the model number to indicate “Tube Packaging”, and “R” for “Reel Packaging”, and “G” for “Tray Packaging”. Absolute Maximum Ratings Parameter Input Voltage (continuous) Ambient Temperature Storage Temperature Min 2.8 V -40 °C -40 °C Typ Max 6V 85 °C 125 °C Notes Input Specifications Parameter Input Voltage Input Current (full load) VO=12V VO=15V Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (rms) I t Inrush Current Transient Turn-on Voltage Threshold 2 Min 3V - Typ 100 mA 30 mA 0.02 A s 2.8 V 2 Max 5.5 V 4.3 A 4.0 A 150 mA 60 mA 0.05 A s 2.9 V 2 Notes With simulated source impedance of 500 nH, 5 Hz to 20 MHz; Use 270 uF/16 V Oscon capacitor with ESR = 0.018 ohm max. at 100 kHz Note: All specifications are typical at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 3.0 V-5.5 V Input 12 V/0.8 A & 15 V/0.6 A Output Output Specifications Parameter Output Voltage Set Point VO=12 V VO=15 V Line Regulation VO=12 V VO=15 V Load Regulation VO=12 V VO=15 V Regulation Over Temperature (-40 °C to +85 °C) VO=12 V VO=15 V Output Current VO=12 V VO=15 V Ripple and Noise (rms) VO=12 V; IO=0 A VO=15 V; IO=0 A VO=12 V; IO=0.8 A VO=15 V; IO=0.6 A Ripple and Noise (pk-pk) VO=12 V; IO=0 A VO=15 V; IO=0 A VO=12 V; IO=0.8 A VO=15 V; IO=0.6 A Rise Time Overshoot at Turn on Output Capacitance 33 uF 20 mV 20 mV 60 mV 80 mV 5 mS 0% 40 mV 40 mV 100 mV 120 mV 5% 330 uF The min output capacitance is 33 uF Tantalum capacitor at the output 5 mV 5 mV 20 mV 30 mV 10 mV 10 mV 40 mV 50 mV Test conditions: BW = 0-20 MHz; 1uF ceramic cap and 33 uF Tantalum capacitor at the output. 0A 0A 0.8 A 0.6 A 60 mV 75 mV 120 mV 150 mV 20 mV 20 mV 40 mV 40 mV 11.580 V 14.475 V 12 V 15 V 12.420 V 15.525 V Min Typ Max Notes Test condition: Vin=5 V, lout=full load - 45 mV 60 mV 80 mV 100 mV Transient Response 50% ~ 100% Max Load 100% ~ 50% Max Load Overshoot Settling Time Overshoot Settling Time All Outputs 130 mV 100 uS 130 mV 100 uS 200 mV 200 uS 200 mV 200 uS di/dt = 0.1 A/uS; Vin = 5 V; and with 33 uF Tantalum capacitor at the output. Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 3.0 V-5.5 V Input 12 V/0.8 A & 15 V/0.6 A Output General Specifications Parameter Efficiency VO=12 V VO=15 V Switching Frequency Output Trim Range MTBF Dimensions (surface mount) Inches (L × W × H) Millimeters (L × W × H) Dimensions (vertical) Inches (L × W × H) Millimeters (L × W × H) Weight 84% 84% 500 kHz 90% VO 88% 88% 550 kHz 7,300,000 hours 0.78 x 0.7 x 0.32 19.81 x 17.78 x 8.13 0.7 x 0.308 x 0.65 17.78 x 7.82 x 16.51 5.2 g 650 kHz 110% VO Calculated Per Bell Core TR-332 (Vin= 5 V; Vo=12 V; IO = 0.64 A; Ta = 25 °C) Min Typ Max Notes Measured at Vin=5 V, full load Note: All specifications are typical at 25 °C unless otherwise stated. Output Trim Equations Equations for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) and the nominal output voltage of the converter (Vnom) are shown below. The Trim Down resistor should be connected between the Trim pin and Vout. The Trim Up resistor should be connected between the Trim pin and Ground. Only one of the resistors should be used for any given application. Rtrim− down = A −B Vnom − Vadj Vout Rtrim-down Module Trim GND Rtrim− up = Vadj C −D − Vnom Vout Module Trim Rtrim-up GND Vnom 12 15.055 A 164.640 209.542 B 21.850 20.600 C 11.760 11.760 D 7.150 5.900 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 3.0 V-5.5 V Input 12 V/0.8 A & 15 V/0.6 A Output Efficiency Data 92.0% 90.0% 3.0V 5.0V 5.5V 95.0% 90.0% Efficiency 85.0% 80.0% 75.0% 70.0% 0.20 0.40 0.60 0.80 Efficiency 88.0% 86.0% 84.0% 82.0% 80.0% 78.0% 0.08 3.0V 5.0V 5.5V 0.06 0.15 0.30 0.45 0.60 Output current (A) Output current (A) x7AH-01FX20 x7AH-01FX50 Thermal Derating Curves x7AH-01FX20 x7AH-01FX50 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 3.0 V-5.5 V Input 12 V/0.8 A & 15 V/0.6 A Output S7AH-01F bel Pin Connections Pin 1 2 3 4 5 6 7 Function N/A Vin Ground Vout Trim N/A N/A V7AH-01F bel bel Pin Connections Pin 1 2 3 4 5 Function N/A Vin Ground Vout Trim 2005 Bel Fuse Inc. Specifications subject to change without notice. 040805 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com