X7BA-06E2AX

NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input 0.75V-5.0V/6A Output x7BA-06E2Ax Series • • • • • • Non-Isolated High Efficiency High Power Density Fixed Frequency Flexible Output Voltage Sequencing Active Low/High (option) • • • • • Under-voltage Lockout (UVLO) Remote On/Off OCP/SCP Wide Input Wide Trim Range Description The Bel x7BA-06E2Ax modules are a series of non-isolated DC/DC converters that can deliver up to 6A of output current with full load efficiency of 92% at 5.0V output. These modules provide precisely regulated voltage programmable via external resistor from 0.75V to 5.0V over a wide range of input voltage. These modules have a sequencing feature that enables designers to implement various types of output voltage sequencing when powering multiple voltages on a board. Their open-frame construction and small footprint enable designers to develop cost and space-efficient solutions. Standard features include remote On/Off, programmable output voltage and over current protection. Part Selection Output Voltage 5.0V 0.75V – 3.3V Input Voltage 7.0V - 14V 4.5V - 14V Max. Output Current 6A 6A Max. Output Power 30.0W 19.8W Typical Efficiency 92% 88% Model Number Surface Mount S7BA-06E2Ax S7BA-06E2Ax Model Number Vertical Mount V7BA-06E2Ax V7BA-06E2Ax Note: Use “0” to replace “x” for remote on/off active high logic and use “L” for active low logic. Add “G” suffix at the end of the model numbers to indicate Tray Packaging. Absolute Maximum Ratings Parameter Input Voltage (continuous) Output Enable Terminal Voltage Sequencing Voltage 1 Min -0.3V -0.3V -0.3V -40°C -55°C Typ - Max 15V 15V Vin 85°C 125°C Notes All specifications are typical at 25°C unless otherwise stated. Ambient Temperature Storage Temperature Note: 1. x7BA-06E2Ax series of modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When the sequencing feature is not used, tie the SEQ pin to Vin. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input 0.75V-5.0V/6A Output Min 4.5V 7.0V Typ 12V 12V 2.75A 1.85A 1.05A 0.55A 3mA 120mA 60mA 0.002A s 4.3V 6.0V 4.0V 5.5V 2 Input Specifications Parameter Input Voltage Vo, set ≤ 3.3V Vo, set = 5.0V Input Current (full load) Vo=5.0V Vo=3.3V Vo=1.8V Vo=0.75V Input Current (no load) Vo=5.0V Vo=0.75V Remote Off Input Current Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (RMS) I t Inrush Current Transient Turn-on Voltage Threshold Vo, set ≤ 3.3V Vo, set = 5.0V Turn-off Voltage Threshold Vo, set ≤ 3.3V Vo, set = 5.0V 2 Max 14V 14V 4.8A 4.8A 3.2A 1.8A 100mA 20mA 5mA 200mA 100mA 0.02A s 4.5V 6.5V 4.3V 6.0V 2 Notes Tested with two 100uF/25V input Tantalum capacitors & simulated source impedance of 1uH, 5Hz to 20MHz. Shut down or below 90% set point. Output Specifications Parameter Output Voltage Set Point 1 Output Voltage Set Point Load Regulation Line Regulation Regulation Over Temperature (-40°C to +85°C) Output Current Current Limit Threshold Short Circuit Surge Transient Ripple and Noise (pk-pk) Vo=5.0V Vo=3.3V Vo=0.75V Ripple and Noise (RMS) Vo=5.0V Vo=3.3V Vo=0.75V Turn on Time Overshoot at Turn on Output Capacitance ESR ≥ 1mohm ESR ≥ 10mohm Transient Response 50% ~ 100% Max Load Settling Time VO = 0.75V -5.0V 100% ~ 50% Max Load Settling Time Min -2%Vo,set -2.5%Vo,set -0.7%Vo,set -0.7%Vo,set 0A 6.8A 0uF 0uF Typ 0.4%Vo,set 0.3%Vo,set 0.5%Vo,set 2 0.25A s 100mV 80mV 35mV 35mV 25mV 10mV 6mS 0% 200mV 25uS 200mV 25uS Max 2%Vo,set 3.5%Vo,set 0.7%Vo,set 0.7%Vo,set 6A 15A 140mV 120mV 70mV 50mV 40mV 15mV 12mS 3% 1000uF 2200uF 350mV 50uS 350mV 50uS di/dt=2.5A/uS; Vin=12V; and with 10uF/10V tantalum capacitor & 1uF/10V ceramic capacitor at the output. Tested with 0-20MHz, with 10uF/10V tantalum capacitor & 1uF/10V ceramic capacitor at the output Notes Vin=12V, full load Io=Io, min to Io, max Vin=Vin, min to Vin, max Tref=Ta, min to Ta, max Notes: All specifications are typical at nominal input (Vin=12V), full load at 25°C unless otherwise stated. 1. Over all operating input voltages, resistive loads and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input Parameter Efficiency Vo=5.0V Vo=3.3V Vo=1.8V Vo=0.75V Switching Frequency Output Voltage Trim Range (wide trim) MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H) Dimensions Inches (L × W × H) Millimeters (L × W × H) Weight 1.0 x 0.5 x 0.243 25.4 x 12.7 x 6.16 5g Vertical Mount 0.8 x 0.45 x 0.251 20.32 x 11.42 x 6.38 Surface Mount 88% 85% 80% 68% 220KHz 0.7525V 92% 88% 84% 73% 250KHz 3,079,469 hours 280KHz 5V Calculated Per Bell Core TR-332 (IO = Nominal; Ta = 25°C) Measured at Vin=12V, full load 0.75V-5.0V/6A Output Min Typ Max Notes General Specifications Note: All specifications are typical at 25°C unless otherwise stated. Control Specifications Parameter Remote On/Off Signal Low (Unit Off) Signal High (Unit On) Signal Low (Unit On) Signal High (Unit Off) Voltage Sequencing Sequencing Voltage Sequencing Slew Rate Capability Sequencing Delay Time Tracking Accuracy Power-Up Power-Down 100mV 200mV 200mV 400mV Min -0.3V 2.5V -0.3V 2.5V 0.05V 10mS Typ Max 0.4V 14V 0.4V 14V Vin 2V/mS Delay from Vin, min to application of voltage on SEQ pin Notes x7BA-06E2A0; Remote On/Off pin open, Unit on. x7BA-06E2AL; Remote On/Off pin open, Unit on. Sequencing Voltage should be higher than output voltage. Output Trim Equations Equation for calculating the trim resistor (in kΩ) given the desired adjusted voltage (Vadj) is shown below. The Trim Up resistor should be connected between the Trim pin and Ground. Vout Rtrim = 10.507 −1 Vadj − 0.7525 Module Trim GND Rtrim Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. Vout Vtrim = 0.7 − 0.0667 × (Vadj − 0.7525) Module Trim Vtrim GND Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input 0.75V-5.0V/6A Output Efficiency Data MODULE 5.0V MODULE 3.3V 100.0% 80.0% 60.0% 40.0% 20.0% 0.0% 1A 2A 3A 4A 5A 100.0% 80.0% 60.0% 40.0% 20.0% 0.0% 1A 2A 3A 4A 5A OUTPUT CURRENT EFFICIENCY 7.0V 12.0V 14.0V EFFICIENCY 4.5V 12.0V 14.0V OUTPUT CURRENT MODULE 1.8V 100.0% EFFICIENCY 90.0% 80.0% 70.0% 60.0% 0.6A 1.5A 3.0A 4.5A 6.0A OUTPUT CURRENT 4.5V 12.0V 14.0V MODULE 0.75V 90.0% 80.0% 70.0% 60.0% 50.0% 0.6A 1.5A 3.0A 4.5A 6.0A OUTPUT CURRENT 4.5V 12.0V 14.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com EFFICIENCY NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input 0.75V-5.0V/6A Output Thermal Derating Curves S7BA-06E2Ax, Vo=0.75V V7BA-06E2Ax, Vo=0.75V S7BA-06E2Ax, Vo=2.5V V7BA-06E2Ax, Vo=2.5V S7BA-06E2Ax, Vo=5.0V V7BA-06E2Ax, Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input 0.75V-5.0V/6A Output S7BA-06E2Ax Pin Connections Pin 1 2 3 4 5 6 Function Remote On/Off Vin+ SEQ Ground Trim Vout+ RECOMMENDED PAD LAYOUT PAD SIZE: MIN: 0.12"* 0.095" (3.05mm * 2.41mm) MAX: 0.135"* 0.11" (3.43mm * 2.79mm) Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com NON-ISOLATED DC/DC CONVERTERS 4.5V-14V Input 0.75V-5.0V/6A Output V7BA-06E2Ax Pin Connections Pin 1 2 3 4 5 6 Function Vout+ Trim Ground SEQ Vin+ Remote On/Off 2005 Bel Fuse Inc. Specifications subject to change without notice. 020405 CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com