BG17A

BeRex 5-4000 MHz Cascadeable InGaP HBT Gain Block Device Features  35dBm Output IP3 at 5dBm/tone at 900MHz  18.8dB Gain at 900MHz  19.2dBm P1dB at 1900MHz  Highly Reliable InGaP/GaAs HBT Technology  Temperature Compensation Circuit patent  SOT-89 Surface Mount Package  50 ohm Cascadeable  Lead-free/Green/RoHS compliant Application: commercial, space, military wireless system Electrical Specifications (Ta = 25C, Vs = 5V) Parameters Test Conditions Frequency Range Gain 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz Vc = 5.0V BG17A Min 5 18.0 17.8 16.0 15.2 Typ 19.0 18.8 17.0 16.2 -18.0 -25.0 -28.0 -19.0 -14.0 -19.0 -13.0 -11.0 35.0 35.0 3 3 .0 31.0 19.0 19.2 19.2 18.0 65 5.0 -0.004 50 Max 4000 20.0 19.8 18.0 17.2 Unit MHz dB S11 dB S22 dB OIP3 P1dB Ic Vc dG/dT Rth 33.0 33.0 31.0 29.0 18.0 18.2 18.2 17.0 55 dBm dBm 75 mA V dB/C C/W Thermal Resistance Test conditions unless otherwise noted. 1. Device performance is measured on BeRex evaluation board at 25C, 50 ohm system. 2. OIP3 measured with two tones at an output power of 5dBm/tone separated by 1MHz. http: //www.berex.com BeRex Absolute Maximum Ratings Parameters Operating Case temperature Storage Temperature Junction Temperature Operating Voltage Supply Current Input RF Power BG17A Rating -40 to +85C -55 to +155C +220C 6.5V 120mA 23dBm Operation of this device above any of these parameters may result in permanent damage. [I-V Characteristics] 140 120 100 Icc [mA] [Generic SOT89 Evaluation Board] +25C -30C +85C BeRex Evaluation Board 80 60 40 20 0 0 1 2 3 4 5 6 MMIC Innovator Vcc [V] *Dielectric constant is 4.2 *RF pattern width 52mil *31mil thick FR4 PCB Application Circuit: 5 - 4000 MHz Schematic Diagram C3 C4 C5 +5V BOM C1 C2 100pF 100pF 100pF Tolerance ± 5% ± 5% ± 5% ± 5% ± 20% 5% L1 RFin C1 BG17A C3 C2 RFout C4 1000pF C5 L1 10uF 33nH Note: Less than 20nH improves RF performance at frequencies over 1.9GHz. 40nH or higher value L1 improves RF performance at frequencies under 500MHz. Optimum value of L1 may vary with board design. http: //www.berex.com BeRex Typical Device Data BG17A S-parameters (Vc=5V, Ic=65mA, T=25C) (Vdevice = 5.0V, Icc = 65mA, T = 25 C) Freq [MHz] 100 500 1000 1500 2000 2500 3000 3500 4000 S-Parameter S21 Ang -122.20 126.30 47.01 -24.69 -93.43 -157.90 140.60 75.26 7.77 S11 Mag 0.71 0.19 0.04 0.03 0.11 0.21 0.28 0.26 0.09 S11 Ang -35.18 -98.08 -145.60 -64.05 -120.90 -162.00 166.20 132.70 100.50 S21 Mag 5.33 8.94 8.68 8.04 6.91 6.46 5.96 5.71 5.53 S12 Mag 0.04 0.07 0.08 0.08 0.08 0.08 0.08 0.09 0.09 S12 Ang 84.17 -27.22 -88.65 -142.30 165.80 116.00 66.91 15.38 -40.82 S22 Mag 0.78 0.21 0.11 0.20 0.30 0.35 0.36 0.29 0.17 S22 Ang 169.90 30.92 -90.84 -166.60 164.20 146.60 128.00 95.79 14.59 http: //www.berex.com BeRex BG17A Typical Performance (Vc = 5V, Ic = 65mA, Ta = 25C) Freq MHz 500 900 1900 2140 S21 dB 19.0 18.8 17.0 16.8 S11 dB -14 -25 -21 -17 S22 dB -13 -19 -11 -10 P1 dBm 19.0 19.2 19.2 19.0 OIP3 dBm 35.0 35.0 33.0 32.5 NF dB 5.2 4.8 4.9 4.9 2450 16.2 -13 -9 18.0 31.0 4.9 3000 15.4 -11 -9 17.5 30.0 5.0 3500 15.5 -15.8 -11 16.0 28.5 5.0 Typical Performance (V device = 4.7 V, Ic = 53 mA, Ta = 25 ℃) Freq MHz 70 500 900 1900 2140 S21 dB 20.7 18.5 18.6 17 16.7 S11 dB -12.6 -15.7 -16.5 -13.7 -13.3 S22 dB -6.2 -9.9 -10.7 -9.4 -9.3 P1 dBm 16.7 16.9 16.7 16.9 16.4 OIP3 dBm 32.5 32.0 30 30.5 29.5 NF dB 5.2 5.2 4.8 4.9 4.9 Typical Performance (V device = 4.5 V, Ic = 45 mA, Ta = 25 ℃) Freq MHz 70 500 900 1900 2140 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 20.6 -12.2 -6.1 15.0 31.0 5.2 18.5 -15.1 -9.6 15.6 31.0 5.2 18.5 -15.5 -10.2 15.3 29.0 4.8 16.7 -13.4 -9.1 16.1 29.0 4.9 16.5 -13 -9 15.9 28.5 4.9 2450 16.3 -14.4 -9.8 16.4 29.5 4.9 3500 15.4 -15.3 -10.9 15.1 27.5 5.0 2450 16.0 -14.1 -9.6 17.0 27.5 4.9 3500 15.3 -14.9 -10.7 16.4 26.5 5.0 http: //www.berex.com BeRex WCDMA 4FA 2140 -60dBc BG17A WCDMA 6FA 2140 -60dBc http: //www.berex.com BeRex BG17A ACLR Device Performance Pin-Pout-Gain 25 20 15 10 5 0 -15 -10 -5 0 5 35% 30% 25% 25 20 15 30% 25% 20% Po/G Po/G PAE 15% 10 10% 5 0 -15 -10 -5 0 5 15% 10% 5% 0% Pin [dBm ] 5% 0% Pin [dBm ] 900MHz, 5V/65mA 1900 MHz, 5V/65mA http: //www.berex.com PAE 20% BeRex BG17A OIP3 F1=500, F2=501MHz +25C 38 -30C +85C 40 +25C -30C +85C F1=900, F2=901MHz 36 38 OIP3 [dBm] OIP3 [dBm] 34 36 32 34 30 32 28 7 9 11 13 15 30 7 9 11 13 15 Po,tot [dBm ] Po,tot [dBm ] F1=1900, F2=1901MHz 38 +25C 36 -30C +85C F1=2140, F2=2141MHz 35 +25C 33 -30C +85C OIP3 [dBm] 34 OIP3 [dBm] 7 9 11 13 15 31 32 29 30 27 28 25 7 9 11 13 15 Po,tot [dBm ] Po,tot [dBm ] F1=2450, F2=2451MHz 35 +25C 33 -30C +85C 36 38 OIP3 Po=5dBm /tone, D F=1MHz OIP3 [dBm] 31 OIP3 [dBm] 34 29 32 27 30 +25C -30C 1500 2000 +85C 2500 25 7 9 11 13 15 28 500 1000 Po,tot [dBm ] Freq [MHz] http: //www.berex.com BeRex ACPR F=500MHz, IS-95A, 9CH-FWD 885KHz Offset 0 +25C -10 -20 -30 -40 -50 -60 -70 -80 8 10 12 14 16 -30C +85C BG17A F=900MHz, IS-95A, 9CH-FWD 885KHz Offset 0 -10 +25C -30C +85C ACPR [dBc] ACPR [dBc] -20 -30 -40 -50 -60 -70 -80 8 10 12 14 16 Po [dBm ] Po [dBm ] F=1900MHz, IS-95A, 9CH-FWD 885KHz Offset 0 +25C -10 -30C +85C IS-95A, 9CH-FWD, 885KHz Offset Po satisfies -45dBc 20 +25C 18 -30C +85C ACPR [dBc] -20 Po [dBm] 8 10 12 14 16 -30 -40 -50 16 14 12 -60 -70 10 500 1000 1500 2000 Po [dBm ] Freq [MHz] Gain Flatness Gain vs Temperature 20 18 S21 [dB] 16 14 12 10 0 500 1000 1500 2000 Freq [MHz] 2500 3000 3500 4000 +25C -30C +85C http: //www.berex.com BeRex BG17A Package Outline Dimension Suggested PCB Land Pattern and PAD Layout PCB Land Pattern PCB Mounting 0.40 1.30 0.40 Ø0.40 0.40 0.75 1.20 1.20 1.20 1.20 1.50 1.00 0.65 2.80 2.00 0.50 Note : All dimension are in millimeters Visit http://www.berex.com for PCB layout http: //www.berex.com BeRex BG17A Tape & Reel SOT89 Packaging information: Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 Devices Per Reel: 1000 Lead plating finish 100% Tin Matte finish. (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns) MSL / ESD Rating ESD Rating: Value: Test: Standard: MSL Rating: Standard: Class 2 Passes